On Thu, 4 Jun 2009 20:52:36 +0300
Imre Deak <imre.deak@xxxxxxxxx> wrote:
> From: Stanley.Miao <stanley.miao@xxxxxxxxxxxxx>
>
> Add glue to control the OMAP_LDP LCD as a frame buffer device
> using the existing dispc.c driver under omapfb.
>
> Patch updated for mainline kernel. Note that the
> drivers/video/omap should be updated to pass omap_lcd_config
> in platform_data. The patch should also be updated to compile
> if twl4030 is not selected, and eventually to use the regulator
> framework.
>
> Signed-off-by: Stanley.Miao <stanley.miao@xxxxxxxxxxxxx>
> Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
> Fixed-by: Jarkko Nikula <jarkko.nikula@xxxxxxxxx>
> Fixed-by: Tony Lindgren <tony@xxxxxxxxxxx>
> CC: linux-arm-kernel@xxxxxxxxxxxxxxxxxxxxxx
> Signed-off-by: Imre Deak <imre.deak@xxxxxxxxx>
> ---
> arch/arm/configs/omap_ldp_defconfig | 54 +++++++++-
> drivers/video/omap/Kconfig | 4 +
> drivers/video/omap/Makefile | 1 +
> drivers/video/omap/lcd_ldp.c | 200 +++++++++++++++++++++++++++++++++++
> 4 files changed, 257 insertions(+), 2 deletions(-)
> create mode 100644 drivers/video/omap/lcd_ldp.c
>
> diff --git a/arch/arm/configs/omap_ldp_defconfig b/arch/arm/configs/omap_ldp_defconfig
> index 679a4a3..b9c4891 100644
> --- a/arch/arm/configs/omap_ldp_defconfig
> +++ b/arch/arm/configs/omap_ldp_defconfig
> @@ -690,6 +690,7 @@ CONFIG_GPIOLIB=y
> # CONFIG_GPIO_MAX732X is not set
> # CONFIG_GPIO_PCA953X is not set
> # CONFIG_GPIO_PCF857X is not set
> +CONFIG_GPIO_TWL4030=y
>
> #
> # PCI GPIO expanders:
> @@ -742,6 +743,7 @@ CONFIG_SSB_POSSIBLE=y
> # CONFIG_MFD_SM501 is not set
> # CONFIG_HTC_EGPIO is not set
> # CONFIG_HTC_PASIC3 is not set
> +CONFIG_TWL4030_CORE=y
> # CONFIG_MFD_TMIO is not set
> # CONFIG_MFD_T7L66XB is not set
> # CONFIG_MFD_TC6387XB is not set
> @@ -767,8 +769,46 @@ CONFIG_DAB=y
> #
> # CONFIG_VGASTATE is not set
> CONFIG_VIDEO_OUTPUT_CONTROL=m
> -# CONFIG_FB is not set
> -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
> +CONFIG_FB=y
> +CONFIG_FIRMWARE_EDID=y
> +# CONFIG_FB_DDC is not set
> +# CONFIG_FB_BOOT_VESA_SUPPORT is not set
> +CONFIG_FB_CFB_FILLRECT=y
> +CONFIG_FB_CFB_COPYAREA=y
> +CONFIG_FB_CFB_IMAGEBLIT=y
> +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
> +# CONFIG_FB_SYS_FILLRECT is not set
> +# CONFIG_FB_SYS_COPYAREA is not set
> +# CONFIG_FB_SYS_IMAGEBLIT is not set
> +# CONFIG_FB_FOREIGN_ENDIAN is not set
> +# CONFIG_FB_SYS_FOPS is not set
> +# CONFIG_FB_SVGALIB is not set
> +# CONFIG_FB_MACMODES is not set
> +# CONFIG_FB_BACKLIGHT is not set
> +CONFIG_FB_MODE_HELPERS=y
> +CONFIG_FB_TILEBLITTING=y
> +
> +#
> +# Frame buffer hardware drivers
> +#
> +# CONFIG_FB_S1D13XXX is not set
> +# CONFIG_FB_VIRTUAL is not set
> +# CONFIG_FB_METRONOME is not set
> +CONFIG_FB_OMAP=y
> +CONFIG_FB_OMAP_LCD_VGA=y
> +# CONFIG_FB_OMAP_LCDC_EXTERNAL is not set
> +# CONFIG_FB_OMAP_BOOTLOADER_INIT is not set
> +CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE=4
> +CONFIG_BACKLIGHT_LCD_SUPPORT=y
> +CONFIG_LCD_CLASS_DEVICE=y
> +# CONFIG_LCD_LTV350QV is not set
> +# CONFIG_LCD_ILI9320 is not set
> +# CONFIG_LCD_TDO24M is not set
> +# CONFIG_LCD_VGG2432A4 is not set
> +CONFIG_LCD_PLATFORM=y
> +CONFIG_BACKLIGHT_CLASS_DEVICE=y
> +# CONFIG_BACKLIGHT_CORGI is not set
> +# CONFIG_BACKLIGHT_GENERIC is not set
>
> #
> # Display device support
> @@ -780,6 +820,16 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m
> #
> # CONFIG_VGA_CONSOLE is not set
> CONFIG_DUMMY_CONSOLE=y
> +CONFIG_FRAMEBUFFER_CONSOLE=y
> +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
> +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
> +# CONFIG_FONTS is not set
> +CONFIG_FONT_8x8=y
> +CONFIG_FONT_8x16=y
> +CONFIG_LOGO=y
> +CONFIG_LOGO_LINUX_MONO=y
> +CONFIG_LOGO_LINUX_VGA16=y
> +CONFIG_LOGO_LINUX_CLUT224=y
> CONFIG_SOUND=y
> CONFIG_SND=y
> # CONFIG_SND_SEQUENCER is not set
> diff --git a/drivers/video/omap/Kconfig b/drivers/video/omap/Kconfig
> index eb05e09..2bffc07 100644
> --- a/drivers/video/omap/Kconfig
> +++ b/drivers/video/omap/Kconfig
> @@ -7,6 +7,10 @@ config FB_OMAP
> help
> Frame buffer driver for OMAP based boards.
>
> +config FB_OMAP_LCD_VGA
> + bool "Use LCD in VGA mode"
> + depends on MACH_OMAP_3430SDP || MACH_OMAP_LDP
> +
> choice
> depends on FB_OMAP && MACH_OVERO
> prompt "Screen resolution"
> diff --git a/drivers/video/omap/Makefile b/drivers/video/omap/Makefile
> index 0d2996a..b63b198 100644
> --- a/drivers/video/omap/Makefile
> +++ b/drivers/video/omap/Makefile
> @@ -29,6 +29,7 @@ objs-y$(CONFIG_MACH_OMAP_OSK) += lcd_osk.o
> objs-y$(CONFIG_MACH_OMAP_APOLLON) += lcd_apollon.o
> objs-y$(CONFIG_MACH_OMAP_2430SDP) += lcd_2430sdp.o
> objs-y$(CONFIG_MACH_OMAP_3430SDP) += lcd_2430sdp.o
> +objs-y$(CONFIG_MACH_OMAP_LDP) += lcd_ldp.o
> objs-y$(CONFIG_MACH_OMAP2EVM) += lcd_omap2evm.o
> objs-y$(CONFIG_MACH_OMAP3EVM) += lcd_omap3evm.o
> objs-y$(CONFIG_MACH_OMAP3_BEAGLE) += lcd_omap3beagle.o
> diff --git a/drivers/video/omap/lcd_ldp.c b/drivers/video/omap/lcd_ldp.c
> new file mode 100644
> index 0000000..8925230
> --- /dev/null
> +++ b/drivers/video/omap/lcd_ldp.c
> @@ -0,0 +1,200 @@
> +/*
> + * LCD panel support for the TI LDP board
> + *
> + * Copyright (C) 2007 WindRiver
> + * Author: Stanley Miao <stanley.miao@xxxxxxxxxxxxx>
> + *
> + * Derived from drivers/video/omap/lcd-2430sdp.c
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License as published by the
> + * Free Software Foundation; either version 2 of the License, or (at your
> + * option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful, but
> + * WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
> + * General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License along
> + * with this program; if not, write to the Free Software Foundation, Inc.,
> + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/delay.h>
> +#include <linux/i2c/twl4030.h>
> +
> +#include <mach/gpio.h>
> +#include <mach/mux.h>
> +#include <mach/omapfb.h>
> +#include <asm/mach-types.h>
> +
> +#define LCD_PANEL_BACKLIGHT_GPIO (15 + OMAP_MAX_GPIO_LINES)
> +#define LCD_PANEL_ENABLE_GPIO (7 + OMAP_MAX_GPIO_LINES)
> +
> +#define LCD_PANEL_RESET_GPIO 55
> +#define LCD_PANEL_QVGA_GPIO 56
> +
> +#ifdef CONFIG_FB_OMAP_LCD_VGA
> +#define LCD_XRES 480
> +#define LCD_YRES 640
> +#define LCD_PIXCLOCK_MAX 41700
> +#else
> +#define LCD_XRES 240
> +#define LCD_YRES 320
> +#define LCD_PIXCLOCK_MAX 185186
> +#endif
> +
> +#define PM_RECEIVER TWL4030_MODULE_PM_RECEIVER
> +#define ENABLE_VAUX2_DEDICATED 0x09
> +#define ENABLE_VAUX2_DEV_GRP 0x20
> +#define ENABLE_VAUX3_DEDICATED 0x03
> +#define ENABLE_VAUX3_DEV_GRP 0x20
> +
> +#define ENABLE_VPLL2_DEDICATED 0x05
> +#define ENABLE_VPLL2_DEV_GRP 0xE0
> +#define TWL4030_VPLL2_DEV_GRP 0x33
> +#define TWL4030_VPLL2_DEDICATED 0x36
> +
> +#define t2_out(c, r, v) twl4030_i2c_write_u8(c, r, v)
> +
> +
> +static int ldp_panel_init(struct lcd_panel *panel,
> + struct omapfb_device *fbdev)
> +{
> + gpio_request(LCD_PANEL_RESET_GPIO, "lcd reset");
> + gpio_request(LCD_PANEL_QVGA_GPIO, "lcd qvga");
> + gpio_request(LCD_PANEL_ENABLE_GPIO, "lcd panel");
> + gpio_request(LCD_PANEL_BACKLIGHT_GPIO, "lcd backlight");
> +
> + gpio_direction_output(LCD_PANEL_QVGA_GPIO, 0);
> + gpio_direction_output(LCD_PANEL_RESET_GPIO, 0);
> + gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 0);
> + gpio_direction_output(LCD_PANEL_BACKLIGHT_GPIO, 0);
> +
> +#ifdef CONFIG_FB_OMAP_LCD_VGA
> + gpio_set_value(LCD_PANEL_QVGA_GPIO, 0);
> +#else
> + gpio_set_value(LCD_PANEL_QVGA_GPIO, 1);
> +#endif
> + gpio_set_value(LCD_PANEL_RESET_GPIO, 1);
> +
> + return 0;
> +}
> +
> +static void ldp_panel_cleanup(struct lcd_panel *panel)
> +{
> + gpio_free(LCD_PANEL_RESET_GPIO);
> + gpio_free(LCD_PANEL_QVGA_GPIO);
> + gpio_free(LCD_PANEL_ENABLE_GPIO);
> + gpio_free(LCD_PANEL_BACKLIGHT_GPIO);
> +}
> +
> +static int ldp_panel_enable(struct lcd_panel *panel)
> +{
> + if (0 != t2_out(PM_RECEIVER, ENABLE_VPLL2_DEDICATED,
> + TWL4030_VPLL2_DEDICATED))
> + return -EIO;
> + if (0 != t2_out(PM_RECEIVER, ENABLE_VPLL2_DEV_GRP,
> + TWL4030_VPLL2_DEV_GRP))
> + return -EIO;
> +
> + gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 1);
> + gpio_direction_output(LCD_PANEL_BACKLIGHT_GPIO, 1);
> +
> + if (0 != t2_out(PM_RECEIVER, ENABLE_VAUX3_DEDICATED,
> + TWL4030_VAUX3_DEDICATED))
> + return -EIO;
> + if (0 != t2_out(PM_RECEIVER, ENABLE_VAUX3_DEV_GRP,
> + TWL4030_VAUX3_DEV_GRP))
> + return -EIO;
> +
> + return 0;
> +}
> +
> +static void ldp_panel_disable(struct lcd_panel *panel)
> +{
> + gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 0);
> + gpio_direction_output(LCD_PANEL_BACKLIGHT_GPIO, 0);
> +
> + t2_out(PM_RECEIVER, 0x0, TWL4030_VPLL2_DEDICATED);
> + t2_out(PM_RECEIVER, 0x0, TWL4030_VPLL2_DEV_GRP);
> + mdelay(4);
Use the msleep() instead of the mdelay().
> +}
> +
> +static unsigned long ldp_panel_get_caps(struct lcd_panel *panel)
> +{
> + return 0;
> +}
> +
> +struct lcd_panel ldp_panel = {
> + .name = "ldp",
> + .config = OMAP_LCDC_PANEL_TFT | OMAP_LCDC_INV_VSYNC |
> + OMAP_LCDC_INV_HSYNC,
> +
> + .bpp = 16,
> + .data_lines = 18,
> + .x_res = LCD_XRES,
> + .y_res = LCD_YRES,
> + .hsw = 3, /* hsync_len (4) - 1 */
> + .hfp = 3, /* right_margin (4) - 1 */
> + .hbp = 39, /* left_margin (40) - 1 */
> + .vsw = 1, /* vsync_len (2) - 1 */
> + .vfp = 2, /* lower_margin */
> + .vbp = 7, /* upper_margin (8) - 1 */
> +
> + .pixel_clock = LCD_PIXCLOCK_MAX,
> +
> + .init = ldp_panel_init,
> + .cleanup = ldp_panel_cleanup,
> + .enable = ldp_panel_enable,
> + .disable = ldp_panel_disable,
> + .get_caps = ldp_panel_get_caps,
> +};
> +
> +static int ldp_panel_probe(struct platform_device *pdev)
> +{
> + omapfb_register_panel(&ldp_panel);
> + return 0;
> +}
> +
> +static int ldp_panel_remove(struct platform_device *pdev)
> +{
> + return 0;
> +}
> +
> +static int ldp_panel_suspend(struct platform_device *pdev, pm_message_t mesg)
> +{
> + return 0;
> +}
> +
> +static int ldp_panel_resume(struct platform_device *pdev)
> +{
> + return 0;
> +}
> +
> +struct platform_driver ldp_panel_driver = {
> + .probe = ldp_panel_probe,
> + .remove = ldp_panel_remove,
> + .suspend = ldp_panel_suspend,
> + .resume = ldp_panel_resume,
> + .driver = {
> + .name = "ldp_lcd",
> + .owner = THIS_MODULE,
> + },
> +};
> +
> +static int __init ldp_panel_drv_init(void)
> +{
> + return platform_driver_register(&ldp_panel_driver);
> +}
> +
> +static void __exit ldp_panel_drv_exit(void)
> +{
> + platform_driver_unregister(&ldp_panel_driver);
> +}
> +
> +module_init(ldp_panel_drv_init);
> +module_exit(ldp_panel_drv_exit);
> --
> 1.6.3.1
>
>
> ------------------------------------------------------------------------------
> OpenSolaris 2009.06 is a cutting edge operating system for enterprises
> looking to deploy the next generation of Solaris that includes the latest
> innovations from Sun and the OpenSource community. Download a copy and
> enjoy capabilities such as Networking, Storage and Virtualization.
> Go to: http://p.sf.net/sfu/opensolaris-get
> _______________________________________________
> Linux-fbdev-devel mailing list
> Linux-fbdev-devel@xxxxxxxxxxxxxxxxxxxxx
> https://lists.sourceforge.net/lists/listinfo/linux-fbdev-devel
>
----------------------------------------------------------------------
Chcesz miec nawigacje GPS ?
Zamow lub przedluz umowe na neostrade, a nawigacja bedzie Twoja.
Kliknij na link po szczegoly! http://link.interia.pl/f219a
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
