On Thu, Jul 12, 2018 at 10:37:37AM +0530, Keerthy wrote:
> Cut down the shutdown time from 2 seconds to 1 sec. In case of roll
> over try again.
>
> Signed-off-by: Keerthy <j-keerthy@xxxxxx>
> ---
>
> Changes in v4:
>
> * Fixed a compilation issue.
> * Extended the roll over check post interrupt programming.
>
> drivers/rtc/rtc-omap.c | 13 +++++++++++--
> 1 file changed, 11 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/rtc/rtc-omap.c b/drivers/rtc/rtc-omap.c
> index 323ff55..88da927 100644
> --- a/drivers/rtc/rtc-omap.c
> +++ b/drivers/rtc/rtc-omap.c
First, the comment above this function would need to be updated as part
of this patch as it refers to the two-second alarm offset.
> @@ -435,17 +435,23 @@ static void omap_rtc_power_off(void)
> struct rtc_time tm;
> unsigned long now;
> u32 val;
> + int seconds;
>
> rtc->type->unlock(rtc);
> /* enable pmic_power_en control */
> val = rtc_readl(rtc, OMAP_RTC_PMIC_REG);
> rtc_writel(rtc, OMAP_RTC_PMIC_REG, val | OMAP_RTC_PMIC_POWER_EN_EN);
>
> - /* set alarm two seconds from now */
> +again:
> + /* Clear any existing ALARM2 event */
> + rtc_writel(rtc, OMAP_RTC_STATUS_REG, OMAP_RTC_STATUS_ALARM2);
Why is this needed? Any pending interrupt is cleared at probe, and a
previous attempt to set the alarm really led to the alarm going off, why
would we retry?
> +
> + /* set alarm one second from now */
> omap_rtc_read_time_raw(rtc, &tm);
> + seconds = tm.tm_sec;
> bcd2tm(&tm);
> rtc_tm_to_time(&tm, &now);
> - rtc_time_to_tm(now + 2, &tm);
> + rtc_time_to_tm(now + 1, &tm);
>
> if (tm2bcd(&tm) < 0) {
> dev_err(&rtc->rtc->dev, "power off failed\n");
> @@ -470,6 +476,9 @@ static void omap_rtc_power_off(void)
> val = rtc_read(rtc, OMAP_RTC_INTERRUPTS_REG);
> rtc_writel(rtc, OMAP_RTC_INTERRUPTS_REG,
> val | OMAP_RTC_INTERRUPTS_IT_ALARM2);
Add a newline here.
> + /* Our calculations started right before the rollover, try again */
Nit: use all lower case unless writing full sentences, which also
matches most of the other comments in this file.
> + if (seconds != rtc_read(omap_rtc_power_off_rtc, OMAP_RTC_SECONDS_REG))
> + goto again;
Here the alarm may have gone off as part of the roll over, in which case
you shouldn't retry.
Add a newline here too.
> rtc->type->lock(rtc);
>
> /*
Thanks,
Johan
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
