Clean up comments and copyrights on the CORE DPLL3 M2 divider change code. Signed-off-by: Paul Walmsley <paul@xxxxxxxxx> --- arch/arm/mach-omap2/sram34xx.S | 45 +++++++++++++++++++++------------------- 1 files changed, 24 insertions(+), 21 deletions(-) diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index d13f1cc..37a1e1f 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -3,13 +3,12 @@ * * Omap3 specific functions that need to be run in internal SRAM * - * (C) Copyright 2007 - * Texas Instruments Inc. - * Rajendra Nayak <rnayak@xxxxxx> + * Copyright (C) 2004, 2007, 2008 Texas Instruments, Inc. + * Copyright (C) 2008 Nokia Corporation * - * (C) Copyright 2004 - * Texas Instruments, <www.ti.com> + * Rajendra Nayak <rnayak@xxxxxx> * Richard Woodruff <r-woodruff2@xxxxxx> + * Paul Walmsley * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -38,13 +37,16 @@ .text /* - * Change frequency of core dpll - * r0 = sdrc_rfr_ctrl r1 = sdrc_actim_ctrla r2 = sdrc_actim_ctrlb r3 = M2 - * r4 = Unlock SDRC DLL? (1 = yes, 0 = no) -- only unlock DLL for + * omap3_sram_configure_core_dpll - change DPLL3 M2 divider + * r0 = new SDRC_RFR_CTRL register contents + * r1 = new SDRC_ACTIM_CTRLA register contents + * r2 = new SDRC_ACTIM_CTRLB register contents + * r3 = new M2 divider setting (only 1 and 2 supported right now) + * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for * SDRC rates < 83MHz * r5 = number of MPU cycles to wait for SDRC to stabilize after * reprogramming the SDRC when switching to a slower MPU speed - * r6 = SDRC_MR_0 register value + * r6 = new SDRC_MR_0 register value * */ ENTRY(omap3_sram_configure_core_dpll) @@ -53,22 +55,22 @@ ENTRY(omap3_sram_configure_core_dpll) ldr r5, [sp, #56] @ load extra args from the stack ldr r6, [sp, #60] @ load extra args from the stack dsb @ flush buffered writes to interconnect - cmp r3, #0x2 - blne configure_sdrc - cmp r4, #0x1 + cmp r3, #0x2 @ if increasing SDRC clk rate, + blne configure_sdrc @ program the SDRC regs early (for RFR) + cmp r4, #0x1 @ set the intended DLL state bleq unlock_dll blne lock_dll - bl sdram_in_selfrefresh @ put the SDRAM in self refresh - bl configure_core_dpll - bl enable_sdrc - cmp r4, #0x1 + bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC + bl configure_core_dpll @ change the DPLL3 M2 divider + bl enable_sdrc @ take SDRC out of idle + cmp r4, #0x1 @ wait for DLL status to change bleq wait_dll_unlock blne wait_dll_lock - cmp r3, #0x1 - beq return_to_sdram - bl configure_sdrc - mov r12, r5 @ if slowing, wait for SDRC to stabilize - bl wait_clk_stable + cmp r3, #0x1 @ if increasing SDRC clk rate, + beq return_to_sdram @ return to SDRAM code, otherwise, + bl configure_sdrc @ reprogram SDRC regs now + mov r12, r5 + bl wait_clk_stable @ wait for SDRC to stabilize return_to_sdram: isb @ prevent speculative exec past here mov r0, #0 @ return value @@ -93,6 +95,7 @@ sdram_in_selfrefresh: bic r12, r12, #0x4 @ clear PWDENA str r12, [r11] @ write back to SDRC_POWER register ldr r12, [r11] @ posted-write barrier for SDRC +idle_sdrc: ldr r11, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg ldr r12, [r11] bic r12, r12, #0x2 @ disable iclk bit for SDRC -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html