Devices using an external encoder, ESD protection and level shifter
such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder
chip. And on var-som-om44, there is external pull up resistor R30.
So the internal CEC pull-up resistor needs to be disabled as otherwise
the external and internal pull are parallel making the pull value
much smaller than intended. This leads into the CEC not working as
reported by Hans Verkuil <hverkuil@xxxxxxxxx>.
Reported-by: Hans Verkuil <hverkuil@xxxxxxxxx>
Cc: Dmitry Lifshitz <lifshitz@xxxxxxxxxxxxxx>
Cc: Tomi Valkeinen <tomi.valkeinen@xxxxxx>
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
---
Dmitry, care to check that also omap5-cm-t54 has external pull on CEC pin?
---
arch/arm/boot/dts/omap4-droid4-xt894.dts | 2 +-
arch/arm/boot/dts/omap4-duovero-parlor.dts | 2 +-
arch/arm/boot/dts/omap4-panda-common.dtsi | 2 +-
arch/arm/boot/dts/omap4-sdp-es23plus.dts | 2 +-
arch/arm/boot/dts/omap4-sdp.dts | 2 +-
arch/arm/boot/dts/omap4-var-om44customboard.dtsi | 2 +-
arch/arm/boot/dts/omap5-board-common.dtsi | 2 +-
arch/arm/boot/dts/omap5-cm-t54.dts | 2 +-
8 files changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts
--- a/arch/arm/boot/dts/omap4-droid4-xt894.dts
+++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts
@@ -373,7 +373,7 @@
/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0)
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
>;
diff --git a/arch/arm/boot/dts/omap4-duovero-parlor.dts b/arch/arm/boot/dts/omap4-duovero-parlor.dts
--- a/arch/arm/boot/dts/omap4-duovero-parlor.dts
+++ b/arch/arm/boot/dts/omap4-duovero-parlor.dts
@@ -100,7 +100,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3) /* hdmi_hpd.gpio_63 */
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
>;
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -267,7 +267,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
diff --git a/arch/arm/boot/dts/omap4-sdp-es23plus.dts b/arch/arm/boot/dts/omap4-sdp-es23plus.dts
--- a/arch/arm/boot/dts/omap4-sdp-es23plus.dts
+++ b/arch/arm/boot/dts/omap4-sdp-es23plus.dts
@@ -10,7 +10,7 @@
/* SDP boards with 4430 ES2.3+ or 4460 have external pullups on SCL & SDA */
&dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -290,7 +290,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
diff --git a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
--- a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
+++ b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi
@@ -122,7 +122,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
diff --git a/arch/arm/boot/dts/omap5-board-common.dtsi b/arch/arm/boot/dts/omap5-board-common.dtsi
--- a/arch/arm/boot/dts/omap5-board-common.dtsi
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -294,7 +294,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP5_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
+ OMAP5_IOPAD(0x13c, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
>;
diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts
--- a/arch/arm/boot/dts/omap5-cm-t54.dts
+++ b/arch/arm/boot/dts/omap5-cm-t54.dts
@@ -266,7 +266,7 @@
dss_hdmi_pins: pinmux_dss_hdmi_pins {
pinctrl-single,pins = <
- OMAP5_IOPAD(0x013c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec */
+ OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */
OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
>;
--
2.13.0
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
