Nishanth, On Wednesday 20 July 2016 09:03 PM, Nishanth Menon wrote: > On 07/20/2016 09:56 AM, Mugunthan V N wrote: >> Add documention of ti,impedance-control which can be used to >> correct MAC impedance mismatch using phy extended registers. >> >> Signed-off-by: Mugunthan V N <mugunthanvnm@xxxxxx> >> --- >> Documentation/devicetree/bindings/net/ti,dp83867.txt | 7 +++++++ >> 1 file changed, 7 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt >> b/Documentation/devicetree/bindings/net/ti,dp83867.txt >> index 5d21141..531ea3c5 100644 >> --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt >> +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt >> @@ -9,6 +9,13 @@ Required properties: >> - ti,fifo-depth - Transmitt FIFO depth- see >> dt-bindings/net/ti-dp83867.h >> for applicable values >> >> +Optional property: >> + - ti,impedance-control - MAC Interface Impedance control to vary the >> + output impedance with an approximate range >> + from 35-70 ohms in 32 steps. Value range can >> + be 0x0 to 0x1f. Lowest impedance value is >> + 0x1f and highest impedance being 0x0. >> + > > Should'nt you be using the impedance values of 35 to 70 as the valid > values here? that would be the hardware description, and the values to > program corresponding to those are 0x00 to 0x1f. Right? > > Rob: is'nt that the right way to do it? Agree that that is usually the right way to do it. I believe this case is bit peculiar though. Here is the extract from the datasheet[1] about how the register in question works. " Output impedance approximate range from 35-70 ohms in 32 steps. Lowest being 11110 and highest being 00000. Range and Step size will vary with process. Default is set to 50 ohms by trim. But the default register value can vary by process. Non default values of MAC I/O impedance can be used based on trace impedance. Mismatch between device and trace impedance can cause voltage overshoot and undershoot. " So clearly, there is no easy correspondence that the hardware guarantees between output impedance ohmage and the register value programmed. Only couple of things are guaranteed. 1) Programming a value of 0 gives approximately 35 ohms 2) Programming a value of 0x1F gives approximately 70 ohms 3) Default value of the register gives 50 ohms (the default value could vary by device). 4) Programming a value in between will give some ohmage in the approximate range 35-70 (curve is unknown). Given this, I am not sure how one can convert a given user supplied ohms values to a reasonable register value. Clearly, the register is supposed to be programmed by experimentation, not calculation. That said, we could take another approach. At least for the current issue we are trying to address, we only need to configure the register to max value. And given the nature of the register, I am pretty sure that is what most people will end up doing. So, may be we have two properties: ti,max-output-impedance ti,min-output-imepdance which configure the impedance to maximum and minimum values respectively. If, in future, someone needs to configure a value in between, he can introduce a more granular property which when then override whatever else is specified. Regards, Sekhar [1] http://www.ti.com/lit/ds/symlink/dp83867ir.pdf -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
