Hi,
On 03/05/16 10:06, Jun Li wrote:
> Hi
>
>>>>>>>>> /**
>>>>>>>>> + * usb_gadget_start - start the usb gadget controller and
>>>>>>>>> +connect to bus
>>>>>>>>> + * @gadget: the gadget device to start
>>>>>>>>> + *
>>>>>>>>> + * This is external API for use by OTG core.
>>>>>>>>> + *
>>>>>>>>> + * Start the usb device controller and connect to bus (enable
>> pull).
>>>>>>>>> + */
>>>>>>>>> +static int usb_gadget_start(struct usb_gadget *gadget) {
>>>>>>>>> + int ret;
>>>>>>>>> + struct usb_udc *udc = NULL;
>>>>>>>>> +
>>>>>>>>> + dev_dbg(&gadget->dev, "%s\n", __func__);
>>>>>>>>> + mutex_lock(&udc_lock);
>>>>>>>>> + list_for_each_entry(udc, &udc_list, list)
>>>>>>>>> + if (udc->gadget == gadget)
>>>>>>>>> + goto found;
>>>>>>>>> +
>>>>>>>>> + dev_err(gadget->dev.parent, "%s: gadget not registered.\n",
>>>>>>>>> + __func__);
>>>>>>>>> + mutex_unlock(&udc_lock);
>>>>>>>>> + return -EINVAL;
>>>>>>>>> +
>>>>>>>>> +found:
>>>>>>>>> + ret = usb_gadget_udc_start(udc);
>>>>>>>>> + if (ret)
>>>>>>>>> + dev_err(&udc->dev, "USB Device Controller didn't
>>>> start: %d\n",
>>>>>>>>> + ret);
>>>>>>>>> + else
>>>>>>>>> + usb_udc_connect_control(udc);
>>>>>>>>
>>>>>>>> For drd, it's fine, but for real otg, gadget connect should be
>>>>>>>> done by
>>>>>>>> loc_conn() instead of gadget start.
>>>>>>>
>>>>>>> It is upto the OTG state machine to call gadget_start() when it
>>>>>>> needs to connect to the bus (i.e. loc_conn()). I see no point in
>>>>>>> calling gadget start before.
>>>>>>>
>>>>>>> Do you see any issue in doing so?
>>>>>>
>>>>>> This is what OTG state machine does:
>>>>>> case OTG_STATE_B_PERIPHERAL:
>>>>>> otg_chrg_vbus(otg, 0);
>>>>>> otg_loc_sof(otg, 0);
>>>>>> otg_set_protocol(fsm, PROTO_GADGET);
>>>>>> otg_loc_conn(otg, 1);
>>>>>> break;
>>>>
>>>> On second thoughts, after seen the OTG state machine.
>>>> otg_set_protocol(fsm, PROTO_GADGET); is always followed by
>>>> otg_loc_conn(otg, 1); And whenever protocol changes to anything other
>>>> the PROTO_GADGET, we use otg_loc_conn(otg, 0);
>>>>
>>>> So otg_loc_conn seems redundant. Can we just get rid of it?
>>>>
>>>> usb_gadget_start() implies that gadget controller starts up and
>>>> enables pull.
>>>> usb_gadget_stop() implies that gadget controller disables pull and
>> stops.
>>>>
>>>>
>>>> Can you please explain why just these 2 APIs are not sufficient for
>>>> full OTG?
>>>>
>>>> Do we want anything to happen between gadget controller start/stop
>>>> and pull on/off?
>>>
>>> "loc_conn" is a standard output parameter in OTG spec, it deserves a
>>> separate api, yes, current implementation of OTG state machine code
>>> seems allow you to combine the 2 things into one, but don't do that,
>>> because they do not always happen together, e.g. for peripheral only B
>>> device (also a part OTG spec: section 7.3), will be fixed in gadget
>>> mode, but it will do gadget connect and disconnect in its diff states,
>>> so, to make the framework common, let's keep them separated.
>>
>> I'm sorry but I didn't understand your comment about "it will do gadget
>> connect and disconnect in its diff states"
>
> Gadget connect means loc_conn(1).
>
>>
>> I am reading the OTG v2.0 specification and loc_conn is always true when
>> b_peripheral or a_peripheral is true and false otherwise.
>
> If you only talk about these 2 states, yes, loc_conn is ture.
>
>>
>> loc_conn is just an internal state variable and it corresponds to our
>> gadget_start/stop() state.
>
> It's not an internal variable, there are OTG state machine
> parameters tables(table 7-x) in OTG spec which have clear lists
> which are "internal variable", which are "input", which are "output"...
>
> Those APIs are driven directly from OTG spec, easily understood so
> code reader can know what's those APIs for. For real OTG, I don't
> see the benefit if get rid of it.
OK, no issues if we don't get rid of it. But I am still in favor of
doing a connect in usb_gadget_start(), because
1) If we split connect/disconnect() and usb_gadget_start/stop() then there is
additional overhead of keeping track whether connect was called or not during
usb_gadget_stop(). Plus we need to take care that users don't call connect/disconnect
outside of start/stop. It is just complicating things.
2) for many controllers there is no difference between run/stop and
connect/disconnect. i.e. a single register bit controls both.
3) it fits well with the OTG specification. OTG specification says
that loc_conn *variable* must be true *after* the device has signalled a connect.
So OTG state machine can safely set loc_conn variable to true after doing
otg_set_protocol(fsm, PROTO_GADGET); and set it to false otherwise.
Note, OTG specification does not say to take any action based on loc_conn.
It is just a connect indicator variable. So we might have to fix this in the
OTG state machine.
My suggestion is to keep it simple for now. Try the OTG implementation,
and later if we find issues then extend it as required.
cheers,
-roger
>
>>
>> As per 7.4.2.3
>> "loc_conn
>> The "local connect" (loc_conn) variable is TRUE when the local device has
>> signaled that it is connected to the bus. This variable is FALSE when the
>> local device has signaled that it is disconnected from the bus"
>>
>> Can you please point me in the specification if there is any place where
>> loc_conn is false and b_peripheral/a_peripheral is true?
>>
>> cheers,
>> -roger
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
