* santosh shilimkar <santosh.shilimkar@xxxxxxxxxx> [150116 16:23]:
> On 1/16/2015 2:50 PM, Tony Lindgren wrote:
> >Similar to omap_gpio_irq_type() let's make sure that the GPIO
> >is usable as an interrupt if the platform init code did not
> >call gpio_request(). Otherwise we can get invalid device access
> >after setup_irq():
> >
> I let Linus W comment on it but IIRC we chewed this issue last
> time and the conclusion was the gpio_request() must have to be called
> directly or indirectly in case of irq line.
This is a corner case where the error is triggered by a wrong,
non-GPIO IRQ so gpio_request() will never be called before setup_irq()
unlike for any legacy platform code.
The legacy and DT cases we're already handling in the gpio-omap.c
driver a while back with:
2f56e0a57ff1 ("gpio/omap: use gpiolib API to mark a GPIO used as an IRQ")
fac7fa162a19 ("gpio/omap: auto-setup a GPIO when used as an IRQ")
fa365e4d7290 ("gpio/omap: maintain GPIO and IRQ usage separately")
And most of that the bank specific hacks we can get rid of by making
the driver multple instances as that allows replacing BANK_USED
with just runtime PM.
> One old thread on possibly similar issue is here[1]
>
>
> >WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x214/0x340()
> >44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Idle): Data Access in Supervisor mode during Functional access
> >...
> >[<c05f21e4>] (__irq_svc) from [<c05f1974>] (_raw_spin_unlock_irqrestore+0x34/0x44)
> >[<c05f1974>] (_raw_spin_unlock_irqrestore) from [<c00914a8>] (__setup_irq+0x244/0x530)
> >[<c00914a8>] (__setup_irq) from [<c00917d4>] (setup_irq+0x40/0x8c)
> >[<c00917d4>] (setup_irq) from [<c0039c8c>] (omap_system_dma_probe+0x1d4/0x2b4)
> >[<c0039c8c>] (omap_system_dma_probe) from [<c03b2200>] (platform_drv_probe+0x44/0xa4)
> >...
> >
> >We can fix this the same way omap_gpio_irq_type() is handling it.
> >
> >Note that the long term solution is to change the gpio-omap driver
> >to handle the banks as separate driver instances. This will allow
> >us to rely on just runtime PM for tracking the bank specific state.
> >
> >Reported-by: Russell King <rmk+kernel@xxxxxxxxxxxxxxxx>
> >Cc: Felipe Balbi <balbi@xxxxxx>
> >Cc: Javier Martinez Canillas <javier@xxxxxxxxxxxx>
> >Cc: Kevin Hilman <khilman@xxxxxxxxxx>
> >Cc: Linus Walleij <linus.walleij@xxxxxxxxxx>
> >Cc: Russell King - ARM Linux <linux@xxxxxxxxxxxxxxxx>
> >Cc: Santosh Shilimkar <ssantosh@xxxxxxxxxx>
> >Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
> >---
> > drivers/gpio/gpio-omap.c | 39 +++++++++++++++++++++++++++++++++------
> > 1 file changed, 33 insertions(+), 6 deletions(-)
> >
> Is it really OMAP specific issue ? On OMAP, clocks needs to enabled for
> GPIO's to work which is what the init is doing but I believe the same
> should apply to other GPIO controllers as well.
In the long run it should be handled by the generic GPIO code IMO.
I doubt that's doable for the -rc series though. Probably only a
few platforms have hit PM related issues like this. And actually
the omap specific hacks become really minimal if we make the driver
have a separate instance for each GPIO bank.
Regards,
Tony
> [1] https://lkml.org/lkml/2013/8/27/509
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
