For omap3, proper implementation of eocz bit is needed. It was
actually a TODO in the driver.
When periodic mode is not enabled, it is neccessary to force reads.
Signed-off-by: Pavel Machek <pavel@xxxxxx>
diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
index 634b6ce..ee63d08 100644
--- a/drivers/thermal/ti-soc-thermal/ti-bandgap.c
+++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
@@ -43,6 +43,8 @@
#include "ti-bandgap.h"
+static int ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id);
+
/*** Helper functions to access registers and their bitfields ***/
/**
@@ -852,14 +831,20 @@ int ti_bandgap_read_temperature(struct ti_bandgap *bgp, int id,
if (ret)
return ret;
+ if (!TI_BANDGAP_HAS(bgp, MODE_CONFIG)) {
+ ret = ti_bandgap_force_single_read(bgp, id);
+ if (ret)
+ return ret;
+ }
+
spin_lock(&bgp->lock);
temp = ti_bandgap_read_temp(bgp, id);
spin_unlock(&bgp->lock);
- ret |= ti_bandgap_adc_to_mcelsius(bgp, temp, &temp);
+ ret = ti_bandgap_adc_to_mcelsius(bgp, temp, &temp);
if (ret)
return -EIO;
*temperature = temp;
return 0;
@@ -917,7 +903,8 @@ void *ti_bandgap_get_sensor_data(struct ti_bandgap *bgp, int id)
static int
ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
{
- u32 temp = 0, counter = 1000;
+ u32 counter = 1000;
+ struct temp_sensor_registers *tsr;
/* Select single conversion mode */
if (TI_BANDGAP_HAS(bgp, MODE_CONFIG))
@@ -925,16 +912,27 @@ ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
/* Start of Conversion = 1 */
RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 1);
- /* Wait until DTEMP is updated */
- temp = ti_bandgap_read_temp(bgp, id);
- while ((temp == 0) && --counter)
- temp = ti_bandgap_read_temp(bgp, id);
- /* REVISIT: Check correct condition for end of conversion */
+ /* Wait for EOCZ going up */
+ tsr = bgp->conf->sensors[id].registers;
+
+ while (--counter) {
+ if (ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
+ tsr->bgap_eocz_mask)
+ break;
+ }
/* Start of Conversion = 0 */
RMW_BITS(bgp, id, temp_sensor_ctrl, bgap_soc_mask, 0);
+ /* Wait for EOCZ going down */
+ counter = 1000;
+ while (--counter) {
+ if (!(ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
+ tsr->bgap_eocz_mask))
+ break;
+ }
+
return 0;
}
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
