Re: [PATCH] net: ethernet: cpsw: fix hangs with interrupts

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



* Felipe Balbi <balbi@xxxxxx> [150102 14:19]:
> The CPSW IP implements pulse-signaled interrupts. Due to
> that we must write a correct, pre-defined value to the
> CPDMA_MACEOIVECTOR register so the controller generates
> a pulse on the correct IRQ line to signal the End Of
> Interrupt.
> 
> The way the driver is written today, all four IRQ lines
> are requested using the same IRQ handler and, because of
> that, we could fall into situations where a TX IRQ fires
> but we tell the controller that we ended an RX IRQ (or
> vice-versa). This situation triggers an IRQ storm on the
> reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
> which will, then, print a ton of:
> 
> 	unexpected IRQ trap at vector 00
> 
> In order to fix the problem, we are moving all calls to
> cpdma_ctlr_eoi() inside the IRQ handler and making sure
> we *always* write the correct value to the CPDMA_MACEOIVECTOR
> register. Note that the algorithm assumes that IRQ numbers and
> value-to-be-written-to-EOI are proportional, meaning that a
> write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
> Interrupt and that's the IRQ number sitting in the 0-th index
> of our irqs_table array.
> 
> This, however, is safe at least for current implementations of
> CPSW so we will refrain from making the check smarter (and, as
> a side-effect, slower) until we actually have a platform where
> IRQ lines are swapped.
> 
> This patch has been tested for several days with AM335x- and
> AM437x-based platforms. AM57x was left out because there are
> still pending patches to enable ethernet in mainline for that
> platform. A read of the TRM confirms the statement on previous
> paragraph.
> 
> Reported-by: Yegor Yefremov <yegorslists@xxxxxxxxxxxxxx>
> Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
> Cc: <stable@xxxxxxxxxxxxxxx> # v3.9+
> Signed-off-by: Felipe Balbi <balbi@xxxxxx>

Makes sense to me. I've seen similar EOI handling issue with
davinci-emac recently that I'll post some fixes for soonish.
It seems the EOI registers just gate the interrupt lines at the
device end without affecting the interrupt status, so:

Acked-by: Tony Lindgren <tony@xxxxxxxxxxx>

> ---
> 
> should be applied on 'net' for current -rc
> 
>  drivers/net/ethernet/ti/cpsw.c | 19 ++++++++-----------
>  1 file changed, 8 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
> index c560f9a..e61ee83 100644
> --- a/drivers/net/ethernet/ti/cpsw.c
> +++ b/drivers/net/ethernet/ti/cpsw.c
> @@ -757,6 +757,14 @@ requeue:
>  static irqreturn_t cpsw_interrupt(int irq, void *dev_id)
>  {
>  	struct cpsw_priv *priv = dev_id;
> +	int value = irq - priv->irqs_table[0];
> +
> +	/* NOTICE: Ending IRQ here. The trick with the 'value' variable above
> +	 * is to make sure we will always write the correct value to the EOI
> +	 * register. Namely 0 for RX_THRESH Interrupt, 1 for RX Interrupt, 2
> +	 * for TX Interrupt and 3 for MISC Interrupt.
> +	 */
> +	cpdma_ctlr_eoi(priv->dma, value);
>  
>  	cpsw_intr_disable(priv);
>  	if (priv->irq_enabled == true) {
> @@ -786,8 +794,6 @@ static int cpsw_poll(struct napi_struct *napi, int budget)
>  	int			num_tx, num_rx;
>  
>  	num_tx = cpdma_chan_process(priv->txch, 128);
> -	if (num_tx)
> -		cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_TX);
>  
>  	num_rx = cpdma_chan_process(priv->rxch, budget);
>  	if (num_rx < budget) {
> @@ -795,7 +801,6 @@ static int cpsw_poll(struct napi_struct *napi, int budget)
>  
>  		napi_complete(napi);
>  		cpsw_intr_enable(priv);
> -		cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_RX);
>  		prim_cpsw = cpsw_get_slave_priv(priv, 0);
>  		if (prim_cpsw->irq_enabled == false) {
>  			prim_cpsw->irq_enabled = true;
> @@ -1310,8 +1315,6 @@ static int cpsw_ndo_open(struct net_device *ndev)
>  	napi_enable(&priv->napi);
>  	cpdma_ctlr_start(priv->dma);
>  	cpsw_intr_enable(priv);
> -	cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_RX);
> -	cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_TX);
>  
>  	prim_cpsw = cpsw_get_slave_priv(priv, 0);
>  	if (prim_cpsw->irq_enabled == false) {
> @@ -1578,9 +1581,6 @@ static void cpsw_ndo_tx_timeout(struct net_device *ndev)
>  	cpdma_chan_start(priv->txch);
>  	cpdma_ctlr_int_ctrl(priv->dma, true);
>  	cpsw_intr_enable(priv);
> -	cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_RX);
> -	cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_TX);
> -
>  }
>  
>  static int cpsw_ndo_set_mac_address(struct net_device *ndev, void *p)
> @@ -1620,9 +1620,6 @@ static void cpsw_ndo_poll_controller(struct net_device *ndev)
>  	cpsw_interrupt(ndev->irq, priv);
>  	cpdma_ctlr_int_ctrl(priv->dma, true);
>  	cpsw_intr_enable(priv);
> -	cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_RX);
> -	cpdma_ctlr_eoi(priv->dma, CPDMA_EOI_TX);
> -
>  }
>  #endif
>  
> -- 
> 2.2.0
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux