[PATCH V2 2/2] ARM: dra7xx: Fix counter frequency drift for AM572x errata i856.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Errata i856 for the AM572x (DRA7xx) points out that the 32.768KHz external
crystal is not enabled at power up.  Instead the CPU falls back to using
an emulation for the 32KHz clock which is SYSCLK1/610.  SYSCLK1 is usually
20MHz on boards so far (which gives an emulated frequency of 32.786KHz),
but can also be 19.2 or 27MHz which result in much larger drift.

Since this is used to drive the master counter at 32.768KHz * 375 /
2 = 6.144MHz, the emulated speed for 20MHz is of by 570ppm, or about 43
seconds per day, and more than the 500ppm NTP is able to tolerate.

Checking the CTRL_CORE_BOOTSTRAP register can determine if the CPU
is using the real 32.768KHz crystal or the emulated SYSCLK1/610, and
by known that the real counter frequency can be determined and used.
The real speed is then SYSCLK1 / 610 * 375 / 2 or SYSCLK1 * 75 / 244.

Signed-off-by: Len Sorensen <lsorense@xxxxxxxxxxxxxxxxxxx>
---
 arch/arm/mach-omap2/control.h |    4 ++++
 arch/arm/mach-omap2/timer.c   |   36 ++++++++++++++++++++++++++++++++++--
 2 files changed, 38 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-omap2/control.h b/arch/arm/mach-omap2/control.h
index a3c0133..a80ac2d 100644
--- a/arch/arm/mach-omap2/control.h
+++ b/arch/arm/mach-omap2/control.h
@@ -286,6 +286,10 @@
 #define OMAP5XXX_CONTROL_STATUS                0x134
 #define OMAP5_DEVICETYPE_MASK          (0x7 << 6)
 
+/* DRA7XX CONTROL CORE BOOTSTRAP */
+#define DRA7_CTRL_CORE_BOOTSTRAP	0x6c4
+#define DRA7_SPEEDSELECT_MASK		(0x3 << 8)
+
 /*
  * REVISIT: This list of registers is not comprehensive - there are more
  * that should be added.
diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index fb0cb2b..7d45c84 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -54,6 +54,7 @@
 
 #include "soc.h"
 #include "common.h"
+#include "control.h"
 #include "powerdomain.h"
 #include "omap-secure.h"
 
@@ -496,7 +497,8 @@ static void __init realtime_counter_init(void)
 	void __iomem *base;
 	static struct clk *sys_clk;
 	unsigned long rate;
-	unsigned int reg, num, den;
+	unsigned int reg;
+	unsigned long long num, den;
 
 	base = ioremap(REALTIME_COUNTER_BASE, SZ_32);
 	if (!base) {
@@ -511,6 +513,35 @@ static void __init realtime_counter_init(void)
 	}
 
 	rate = clk_get_rate(sys_clk);
+
+	if (soc_is_dra7xx()) {
+		/*
+		 * Errata i856 says the 32.768KHz crystal does not start at
+		 * power on, so the CPU falls back to an emulated 32KHz clock
+		 * based on sysclk / 610 instead. This causes the master counter
+		 * frequency to not be 6.144MHz but at sysclk / 610 * 375 / 2
+		 * (OR sysclk * 75 / 244)
+		 *
+		 * This affects at least the DRA7/AM572x 1.0, 1.1 revisions.
+		 * Of course any board built without a populated 32.768KHz
+		 * crystal would also need this fix even if the CPU is fixed
+		 * later.
+		 *
+		 * Either case can be detected by using the two speedselect bits
+		 * If they are not 0, then the 32.768KHz clock driving the
+		 * coarse counter that corrects the fine counter every time it
+		 * ticks is actually rate/610 rather than 32.768KHz and we
+		 * should compensate to avoid the 570ppm (at 20MHz, much worse
+		 * at other rates) too fast system time.
+		 */
+		reg = omap_ctrl_readl(DRA7_CTRL_CORE_BOOTSTRAP);
+		if (reg & DRA7_SPEEDSELECT_MASK) {
+			num = 75;
+			den = 244;
+			goto sysclk1_based;
+		}
+	}
+
 	/* Numerator/denumerator values refer TRM Realtime Counter section */
 	switch (rate) {
 	case 12000000:
@@ -545,6 +576,7 @@ static void __init realtime_counter_init(void)
 		break;
 	}
 
+sysclk1_based:
 	/* Program numerator and denumerator registers */
 	reg = readl_relaxed(base + INCREMENTER_NUMERATOR_OFFSET) &
 			NUMERATOR_DENUMERATOR_MASK;
@@ -556,7 +588,7 @@ static void __init realtime_counter_init(void)
 	reg |= den;
 	writel_relaxed(reg, base + INCREMENTER_DENUMERATOR_RELOAD_OFFSET);
 
-	arch_timer_freq = (rate / den) * num;
+	arch_timer_freq = DIV_ROUND_UP_ULL(rate * num, den);
 	set_cntfreq();
 
 	iounmap(base);
-- 
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux