On Fri, Jul 18, 2014 at 10:35:10AM +0200, Sebastian Andrzej Siewior wrote:
> On 07/17/2014 06:18 PM, Felipe Balbi wrote:
>
> >> No, this is okay. If you look, it checks for "up->ier &
> >> UART_IER_THRI". On the second invocation it will see that this
> >> bit is already set and therefore won't call get_sync() for the
> >> second time. That bit is removed in the _stop_tx() path.
> >
> > oh, right. But that's actually unnecessary. Calling
> > pm_runtime_get() multiple times will just increment the usage
> > counter multiple times, which means you can call __stop_tx()
> > multiple times too and everything gets balanced, right ?
>
> No. start_tx() will be called multiple times but only the first
> invocation invoke pm_runtime_get(). Now I noticed that I forgot to
right, but that's unnecessary. You can pm_runtime_get() every time
start_tx() is called. Just make sure to put everytime stop_tx() is
called too.
> remove pm_runtime_put_autosuspend() at the bottom of it. But you get
> the idea right?
> pm_get() on the while the UART_IER_THRI is not yet set. pm_put() once
> the fifo is completely empty.
>
> >> Do you have other ideas? It doesn't look like this is exported at
> >> all. If we call _stop_tx() right away, then we have 64 bytes in
> >> the TX fifo in the worst case. They should be gone "soon" but the
> >> HW-flow control may delay it (in theory for a long time)).
> >
> > this can be problematic, specially for OMAP which can go into OFF
> > while idle. Whatever is in the FIFO would get lost. It seems like
> > omap-serial solved this within transmit_chars().
>
> No, it didn't.
>
> > See how transmit_chars() is called from within IRQ handler with
> > clocks enabled then it conditionally calls serial_omap_stop_tx()
> > which will pm_runtime_get_sync() -> do_the_harlem_shake() ->
> > pm_runtime_put_autosuspend(). That leaves one unbalanced
> > pm_runtime_get() which is balanced when we're exitting the IRQ
> > handler.
>
> omap-serial and the 8250 do the following on tx path:
> - start_tx()
> -> sets UART_IER_THRI. This will generate an interrupt once the FIFO
> is empty.
> - interrupt, notices the empty fifo, invokes serial8250_start_tx()/
> transmit_chars().
> Both have a while loop that fills the FIFO. This loop is left once
> the tty-buffer is empty (uart_circ_empty() is true) or the FIFO full.
>
> Lets say you filled 64 bytes into the FIFO and then left because your
> FIFO is full and tty-buffer is empty. That means you will invoke
> serial_omap_stop_tx() and remove UART_IER_THRI bit.
> This is okay because you are not interested in further FIFO empty
> interrupts because you don't have any TX-bytes to be sent. However,
> once you leave the transmit_chars() you leave serial_omap_irq() which
> does the last pm_put(). That means you have data in the TX FIFO that is
> about to be sent and the device is in auto-suspend.
> This is "fine" as long as the timeout is greater then the time required
> for the data be sent (plus assuming HW-float control does not stall it
> for too long) so nobody notices a thing.
the time is set to -1 by default. I guess this only works because nobody
has ever tested long transfers with slow baud rates :-p
> For that reason I added the hack / #if0 block in the 8250 driver. To
> ensure we do not disable the TX-FIFO-empty interrupt even if there is
> nothing to send. Instead we enter serial8250_tx_chars() once again with
> empty FIFO and empty tty-buffer and will invoke _stop_tx() which also
> finally does the pm_put().
> That is the plan. The problem I have is how to figure out that the
> device is using auto-suspend. If I don't then I would have to remove
> the #if0 block and that would mean for everybody an extra interrupt
> (which I wanted to avoid).
looks like the closest you have is:
if (pm_runtime_autosuspend_expiration(dev) > 0)
foo();
Another possibility would be to implement the ->runtime_idle() callback
and only return 0 if fifo is empty, otherwise return -EAGAIN ? then, if
the autosuspend timer expires, ->runtime_idle gets called and you can do
the right thing depending on fifo empty or not.
Take a look at
drivers/usb/core/driver.c::usb_runtime_{idle,resume,suspend} for
examples. That seems to work pretty well.
> > This seems work fine and dandy without DMA, but for DMA work, I
> > think we need to make sure this IP stays powered until we get DMA
> > completion callback. But that's future, I guess.
>
> Yes, probably. That means one get at dma start, one put at dma complete
> callback. And I assume we get that callbacks once the DMA transfer is
> complete, not when the FIFO is empty :) So lets leave it to the future
> for now…
k
--
balbi
Attachment:
signature.asc
Description: Digital signature
