>From: Quadros, Roger
>
>Instead of hardcoding use the pre-calculated chip->ecc.steps for
>configuring number of sectors to process with the BCH algorithm.
>
>This also avoids unnecessary access to the ECC_CONFIG register in
>omap_calculate_ecc_bch().
>
>Signed-off-by: Roger Quadros <rogerq@xxxxxx>
>---
> drivers/mtd/nand/omap2.c | 9 +++------
> 1 file changed, 3 insertions(+), 6 deletions(-)
>
>diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
>index 5b8739c..6f3d7cd 100644
>--- a/drivers/mtd/nand/omap2.c
>+++ b/drivers/mtd/nand/omap2.c
>@@ -1066,10 +1066,10 @@ static void __maybe_unused omap_enable_hwecc_bch(struct mtd_info
>*mtd, int mode)
> unsigned int ecc_size1, ecc_size0;
>
> /* GPMC configurations for calculating ECC */
>+ nsectors = chip->ecc.steps;
> switch (ecc_opt) {
> case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
> bch_type = 0;
>- nsectors = 1;
> if (mode == NAND_ECC_READ) {
> wr_mode = BCH_WRAPMODE_6;
> ecc_size0 = BCH_ECC_SIZE0;
>@@ -1082,7 +1082,6 @@ static void __maybe_unused omap_enable_hwecc_bch(struct mtd_info
>*mtd, int mode)
> break;
> case OMAP_ECC_BCH4_CODE_HW:
> bch_type = 0;
>- nsectors = chip->ecc.steps;
> if (mode == NAND_ECC_READ) {
> wr_mode = BCH_WRAPMODE_1;
> ecc_size0 = BCH4R_ECC_SIZE0;
>@@ -1095,7 +1094,6 @@ static void __maybe_unused omap_enable_hwecc_bch(struct mtd_info
>*mtd, int mode)
> break;
> case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
> bch_type = 1;
>- nsectors = 1;
> if (mode == NAND_ECC_READ) {
> wr_mode = BCH_WRAPMODE_6;
> ecc_size0 = BCH_ECC_SIZE0;
>@@ -1108,7 +1106,6 @@ static void __maybe_unused omap_enable_hwecc_bch(struct mtd_info
>*mtd, int mode)
> break;
> case OMAP_ECC_BCH8_CODE_HW:
> bch_type = 1;
>- nsectors = chip->ecc.steps;
> if (mode == NAND_ECC_READ) {
> wr_mode = BCH_WRAPMODE_1;
> ecc_size0 = BCH8R_ECC_SIZE0;
>@@ -1121,7 +1118,6 @@ static void __maybe_unused omap_enable_hwecc_bch(struct mtd_info
>*mtd, int mode)
> break;
> case OMAP_ECC_BCH16_CODE_HW:
> bch_type = 0x2;
>- nsectors = chip->ecc.steps;
> if (mode == NAND_ECC_READ) {
> wr_mode = 0x01;
> ecc_size0 = 52; /* ECC bits in nibbles per sector */
>@@ -1176,6 +1172,7 @@ static int __maybe_unused omap_calculate_ecc_bch(struct mtd_info *mtd,
> {
> struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
> mtd);
>+ struct nand_chip *chip = mtd->priv;
> int eccbytes = info->nand.ecc.bytes;
> struct gpmc_nand_regs *gpmc_regs = &info->reg;
> u8 *ecc_code;
>@@ -1183,7 +1180,7 @@ static int __maybe_unused omap_calculate_ecc_bch(struct mtd_info *mtd,
> u32 val;
> int i, j;
>
>- nsectors = ((readl(info->reg.gpmc_ecc_config) >> 4) & 0x7) + 1;
>+ nsectors = chip->ecc.steps;
Sorry NAK.. I'm sure you are breaking something here :-)
NAND driver supports multiple ECC schemes like;
OMAP_ECC_CODE_HAM1_HW (support for legacy reasons)
OMAP_ECC_CODE_BCH4_HW_DETECTION_SW (needed for OMAP3 and AM35xx)
OMAP_ECC_CODE_BCH4_HW
OMAP_ECC_CODE_BCH8_HW
OMAP_ECC_CODE_BCH8_HW_DETECTION_SW (needed for OMAP3 and AM35xx)
OMAP_ECC_CODE_BCH16_HW
IIRC ..
- software based ecc-schemes OMAP_ECC_CODE_BCHx_HW_DETECTION_SW
Reads/Write in per-sector granularity. (here nsector != chip->ecc.steps)
- hardware based ecc-schemes OMAP_ECC_CODE_BCHx_HW, perform
Reads/Write in per-page granularity (or something like this).
Therefore you have custom implementation of
chip->ecc.read_page = omap_read_page_bch()
Also if you change the configurations here, it will break the compatibility with
u-boot, so images flashed via u-boot will stop to boot in kernel and vice-versa.
I suggest, please refrain from these tweaks for now..
All these optimizations have been tested on multiple scenario so please test
all ecc-schemes before doing anything, otherwise you will end-up in
a bad loop of breaking and fixing NAND driver :-).
with regards, pekon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
