From: Minal Shah <minalkshah@xxxxxxxxx>
DRA7xx platform has in-build GPMC and ELM h/w engines which can be used
for accessing externel NAND flash device. This patch:
- adds generic DT binding in dra7.dtsi for enabling GPMC and ELM h/w engines
- adds DT binding for Micron NAND Flash (MT29F2G16AADWP) present on dra7-evm
*Important*
On DRA7 EVM, GPMC_WPN and NAND_BOOTn are controlled by DIP switch
So following board settings are required for NAND device detection:
SW5.9 (GPMC_WPN) = LOW
SW5.1 (NAND_BOOTn) = HIGH
Signed-off-by: Minal Shah <minalkshah@xxxxxxxxx>
Signed-off-by: Pekon Gupta <pekon@xxxxxx>
Reviewed-by: Javier Martinez Canillas <javier@xxxxxxxxxxxx>
---
arch/arm/boot/dts/dra7-evm.dts | 118 +++++++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/dra7.dtsi | 20 +++++++
2 files changed, 138 insertions(+)
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index ec77907..e624c17 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -120,6 +120,37 @@
0x284 (PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
>;
};
+
+ nand_flash_x16: nand_flash_x16 {
+ /* On DRA7 EVM, GPMC_WPN and NAND_BOOTn comes from DIP switch
+ * So NAND flash requires following switch settings:
+ * SW5.9 (GPMC_WPN) = LOW
+ * SW5.1 (NAND_BOOTn) = HIGH */
+ pinctrl-single,pins = <
+ 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */
+ 0x4 (PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */
+ 0x8 (PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */
+ 0xc (PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */
+ 0x10 (PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */
+ 0x14 (PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */
+ 0x18 (PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */
+ 0x1c (PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */
+ 0x20 (PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */
+ 0x24 (PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */
+ 0x28 (PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */
+ 0x2c (PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */
+ 0x30 (PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */
+ 0x34 (PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */
+ 0x38 (PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */
+ 0x3c (PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */
+ 0xd8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0 */
+ 0xcc (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */
+ 0xb4 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0 */
+ 0xc4 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */
+ 0xc8 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */
+ 0xd0 (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle */
+ >;
+ };
};
&i2c1 {
@@ -377,3 +408,90 @@
pinctrl-names = "default";
pinctrl-0 = <&usb2_pins>;
};
+
+&elm {
+ status = "okay";
+};
+
+&gpmc {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_flash_x16>;
+ ranges = <0 0 0 0x01000000>; /* minimum GPMC partition = 16MB */
+ nand@0,0 {
+ reg = <0 0 0x37c>; /* device IO registers */
+ ti,nand-ecc-opt = "bch8";
+ ti,elm-id = <&elm>;
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <40>;
+ gpmc,cs-wr-off-ns = <40>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <30>;
+ gpmc,adv-wr-off-ns = <30>;
+ gpmc,we-on-ns = <5>;
+ gpmc,we-off-ns = <25>;
+ gpmc,oe-on-ns = <2>;
+ gpmc,oe-off-ns = <20>;
+ gpmc,access-ns = <20>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,rd-cycle-ns = <40>;
+ gpmc,wr-cycle-ns = <40>;
+ gpmc,wait-pin = <0>;
+ gpmc,wait-on-read;
+ gpmc,wait-on-write;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ /* MTD partition table */
+ /* All SPL-* partitions are sized to minimal length
+ * which can be independently programmable. For
+ * NAND flash this is equal to size of erase-block */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "NAND.SPL";
+ reg = <0x00000000 0x000020000>;
+ };
+ partition@1 {
+ label = "NAND.SPL.backup1";
+ reg = <0x00020000 0x00020000>;
+ };
+ partition@2 {
+ label = "NAND.SPL.backup2";
+ reg = <0x00040000 0x00020000>;
+ };
+ partition@3 {
+ label = "NAND.SPL.backup3";
+ reg = <0x00060000 0x00020000>;
+ };
+ partition@4 {
+ label = "NAND.u-boot-spl-os";
+ reg = <0x00080000 0x00040000>;
+ };
+ partition@5 {
+ label = "NAND.u-boot";
+ reg = <0x000c0000 0x00100000>;
+ };
+ partition@6 {
+ label = "NAND.u-boot-env";
+ reg = <0x001c0000 0x00020000>;
+ };
+ partition@7 {
+ label = "NAND.u-boot-env";
+ reg = <0x001e0000 0x00020000>;
+ };
+ partition@8 {
+ label = "NAND.kernel";
+ reg = <0x00200000 0x00800000>;
+ };
+ partition@9 {
+ label = "NAND.file-system";
+ reg = <0x00a00000 0x0f600000>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 6af8b08..a8a0cee 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -964,6 +964,26 @@
dr_mode = "otg";
};
};
+
+ elm: elm@48078000 {
+ compatible = "ti,am3352-elm";
+ reg = <0x48078000 0xfc0>; /* device IO registers */
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "elm";
+ status = "disabled";
+ };
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x50000000 0x37c>; /* device IO registers */
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ status = "disabled";
+ };
};
};
--
1.8.5.1.163.gd7aced9
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
