On 05/09/2014 08:27 AM, Santosh Shilimkar wrote:
> On Friday 09 May 2014 08:54 AM, Nishanth Menon wrote:
>> On 05/08/2014 11:22 PM, Joel Fernandes wrote:
>>> On Thu, May 8, 2014 at 7:25 PM, Santosh Shilimkar
>>> <santosh.shilimkar@xxxxxx> wrote:
>> [...]
>>> Ok, thanks for pointing to the post.
>>>
>>
>>
>> Yep - thanks Santosh for clarifying this. Now, we still have the
>> issues that I pointed out in [1] - without resolving which, we should
>> not enable crossbar for dra74x/72x.
>>
>> A. taking example of PMU
>> interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>
>> this wont work. instead the crossbar driver needs some sort of a hint
>> to know that it should not map these on crossbar register instead
>> assign GIC mapping directly.
>>
>> I propose doing the following
>> #define GIC_CROSSBAR_PASSTHROUGH(irq_no) ((irq_no) | (0x1 << 31))
>>
>> and dts will define the following:
>> interrupts = <GIC_SPI GIC_CROSSBAR_PASSTHROUGH(131) IRQ_TYPE_LEVEL_HIGH>
>>
>> This will also work for the other cases (B.2, B.3)
>>
>> For B.2: L3_APP_IRQ:
>> instead of:
>> interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>
>> we do:
>> interrupts = <GIC_SPI GIC_CROSSBAR_PASSTHROUGH(10) IRQ_TYPE_LEVEL_HIGH>
>>
>> For B.3: NMI
>> interrupts = <GIC_SPI GIC_CROSSBAR_PASSTHROUGH(133) IRQ_TYPE_LEVEL_HIGH>
>>
> We can't do add a flag to generic interrupt controller flags since its
> very specific to cross-bar.
>
>> xlate is easy ->
>>
>> diff --git a/drivers/irqchip/irq-crossbar.c
>> b/drivers/irqchip/irq-crossbar.c
>> index de021638..fd09ab4 100644
>> --- a/drivers/irqchip/irq-crossbar.c
>> +++ b/drivers/irqchip/irq-crossbar.c
>> @@ -112,6 +112,10 @@ static int crossbar_domain_xlate(struct
>> irq_domain *d,
>> {
>> unsigned long ret;
>>
>> + /* Check to see if direct GIC mapping is required */
>> + if (intspec[1] & BIT(31))
>> + return intspec[1] & ~BIT[31];
>> +
>> ret = get_prev_map_irq(intspec[1]);
>> if (!IS_ERR_VALUE(ret))
>> goto found;
>>
>> But then, crossbar_domain_map and crossbar_domain_unmap need hints as
>> well to know that there is no corresponding crossbar registers.
>> Have'nt thought through that yet. Looking to hear about opinions here.
>>
>>
> May be we need additional property like reserved to take care of 1:1
> map.
>
> ti,irqs-direct-map = <131 132>;
>
We already have equivalents for these -> reserved and skip. Problem is
how does crossbar driver know the difference between direct maps and
crossbar value?
6 is one of those reserved ones. dts for a device says:
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>
Now, xlate gets intspec[1] = 6. 6 is valid crossbar number
PRM_IRQ_MPU, however GIC 6 is mapped to WD_TIMER_MPU_C1_IRQ_WARN ->
you need to be able to get a hint that this is direct mapping dts
intended.
in the "6" example:
How do i get PRM_IRQ_MPU?
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>
How do I get WD_TIMER_MPU_C1_IRQ_WARN?
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH> ????? - that wont work as
crossbar driver thinks it is crossbar 6 (PRM_IRQ_MPU)
--
Regards,
Nishanth Menon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
