Add support for VAR-SOM-OM44[1] SODIMM system on module from Variscite. SoM features a OMAP4460, 1GB RAM, Gigabit Ethernet (LAN7500) and optional WLAN/BT. Also add support for VAR-STK-OM44 development board from Variscite. This kit features a VAR-SOM-OM44 and the carrier board VAR-OM44CustomBoard[2]. The VAR-STK-OM44 is the same as VAR-DVK-OM44 but without the LCD display. omap4-var-stk-om44.dts replace the old and very limited omap4-var-som.dts. [1] http://www.variscite.com/products/system-on-module-som/cortex-a9/var-som-om44-cpu-ti-omap-4-omap4460 [2] http://www.variscite.com/products/single-board-computers/var-om44customboard Signed-off-by: Joachim Eastwood <manabian@xxxxxxxxx> --- .../devicetree/bindings/arm/omap/omap.txt | 3 + .../devicetree/bindings/vendor-prefixes.txt | 1 + arch/arm/boot/dts/Makefile | 2 +- arch/arm/boot/dts/omap4-var-om44customboard.dtsi | 235 ++++++++++++++ arch/arm/boot/dts/omap4-var-som-om44.dtsi | 343 +++++++++++++++++++++ arch/arm/boot/dts/omap4-var-som.dts | 96 ------ arch/arm/boot/dts/omap4-var-stk-om44.dts | 16 + 7 files changed, 599 insertions(+), 97 deletions(-) create mode 100644 arch/arm/boot/dts/omap4-var-om44customboard.dtsi create mode 100644 arch/arm/boot/dts/omap4-var-som-om44.dtsi delete mode 100644 arch/arm/boot/dts/omap4-var-som.dts create mode 100644 arch/arm/boot/dts/omap4-var-stk-om44.dts diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 36ede19a1630..7db69ac46188 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -102,6 +102,9 @@ Boards: - OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4"; +- OMAP4 VAR-STK-OM44 : Commercial dev kit with VAR-OM44CustomBoard and VAR-SOM-OM44 w/WLAN + compatible = "variscite,var-stk-om44", "variscite,var-som-om44", "ti,omap4430", "ti,omap4"; + - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x compatible = "ti,omap3-evm", "ti,omap3" diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 0f01c9bf19c8..8a149a4b07de 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -112,6 +112,7 @@ tlm Trusted Logic Mobility toshiba Toshiba Corporation toumaz Toumaz v3 V3 Semiconductor +variscite Variscite Ltd. via VIA Technologies, Inc. voipac Voipac Technologies s.r.o. winbond Winbond Electronics corp. diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 35c146f31e46..f443ade8ae3c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -273,7 +273,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ omap4-panda.dtb \ omap4-panda-a4.dtb \ omap4-panda-es.dtb \ - omap4-var-som.dtb \ + omap4-var-stk-om44.dtb \ omap4-sdp.dtb \ omap4-sdp-es23plus.dtb \ omap5-uevm.dtb \ diff --git a/arch/arm/boot/dts/omap4-var-om44customboard.dtsi b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi new file mode 100644 index 000000000000..7c8e383b2cd0 --- /dev/null +++ b/arch/arm/boot/dts/omap4-var-om44customboard.dtsi @@ -0,0 +1,235 @@ +/* + * Copyright (C) 2014 Joachim Eastwood <manabian@xxxxxxxxx> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/input/input.h> + +/ { + aliases { + display0 = &hdmi0; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_led_pins>; + + led0 { + label = "var:green:led0"; + gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; /* gpio 173 */ + linux,default-trigger = "heartbeat"; + }; + + led1 { + label = "var:green:led1"; + gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>; /* gpio 172 */ + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_key_pins>; + #address-cells = <1>; + #size-cells = <0>; + + user-key@184 { + label = "user"; + gpios = <&gpio6 24 GPIO_ACTIVE_HIGH>; /* gpio 184 */ + linux,code = <BTN_EXTRA>; + gpio-key,wakeup; + }; + }; + + hdmi0: connector@0 { + compatible = "hdmi-connector"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_hpd_pins>; + label = "hdmi"; + type = "a"; + + hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; /* gpio_63 */ + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + }; +}; + +&omap4_pmx_core { + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0xfc (PIN_INPUT_PULLUP | MUX_MODE1) /* mcspi1_cs2.uart1_cts */ + 0xfe (PIN_OUTPUT | MUX_MODE1) /* mcspi1_cs3.uart1_rts */ + 0xe6 (PIN_INPUT_PULLUP | MUX_MODE1) /* i2c2_scl.uart1_rx */ + 0xe8 (PIN_OUTPUT | MUX_MODE1) /* i2c2_sda.uart1_tx */ + >; + }; + + mcspi1_pins: pinmux_mcspi1_pins { + pinctrl-single,pins = < + 0xf2 (PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ + 0xf4 (PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ + 0xf6 (PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ + 0xf8 (PIN_INPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ + >; + }; + + mcasp_pins: pinmux_mcsasp_pins { + pinctrl-single,pins = < + 0xb8 (PIN_OUTPUT | MUX_MODE2) /* mcbsp2_dr.abe_mcasp_axr */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + 0x122 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */ + 0x124 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */ + 0x126 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */ + 0x128 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */ + 0x12a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */ + 0x12c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */ + 0x12e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */ + 0x130 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */ + 0x132 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */ + 0x134 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */ + 0x136 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */ + 0x174 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */ + 0x176 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */ + 0x178 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */ + 0x17a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */ + 0x17c (PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */ + 0x17e (PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */ + 0x180 (PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */ + 0x182 (PIN_OUTPUT | MUX_MODE5) /* dispc2_de */ + 0x184 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */ + 0x186 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */ + 0x188 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */ + 0x18a (PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */ + 0x18c (PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */ + 0x18e (PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */ + 0x190 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */ + 0x192 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */ + 0x194 (PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */ + >; + }; + + dss_hdmi_pins: pinmux_dss_hdmi_pins { + pinctrl-single,pins = < + 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + 0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + >; + }; + + i2c4_pins: pinmux_i2c4_pins { + pinctrl-single,pins = < + 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ + >; + }; + + mmc5_pins: pinmux_mmc5_pins { + pinctrl-single,pins = < + 0x0b6 (PIN_INPUT | MUX_MODE3) /* abe_mcbsp2_clkx.gpio_110 */ + 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ + 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ + 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ + 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ + 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ + >; + }; + + gpio_led_pins: pinmux_gpio_led_pins { + pinctrl-single,pins = < + 0x13e (PIN_OUTPUT | MUX_MODE3) /* kpd_col4.gpio_172 */ + 0x140 (PIN_OUTPUT | MUX_MODE3) /* kpd_col5.gpio_173 */ + >; + }; + + gpio_key_pins: pinmux_gpio_key_pins { + pinctrl-single,pins = < + 0x162 (PIN_INPUT | MUX_MODE3) /* sys_boot0.gpio_184 */ + >; + }; + + ks8851_irq_pins: pinmux_ks8851_irq_pins { + pinctrl-single,pins = < + 0x13c (PIN_INPUT_PULLUP | MUX_MODE3) /* kpd_col3.gpio_171 */ + >; + }; + + hdmi_hpd_pins: pinmux_hdmi_hpd_pins { + pinctrl-single,pins = < + 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ + >; + }; + + backlight_pins: pinmux_backlight_pins { + pinctrl-single,pins = < + 0xd6 (PIN_OUTPUT | MUX_MODE3) /* abe_dmic_din3.gpio_122 */ + >; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + clock-frequency = <400000>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&mcspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi1_pins>; + status = "okay"; + + eth@0 { + compatible = "ks8851"; + pinctrl-names = "default"; + pinctrl-0 = <&ks8851_irq_pins>; + spi-max-frequency = <24000000>; + reg = <0>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; /* gpio 171 */ + }; +}; + +&mmc5 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc5_pins>; + vmmc-supply = <&vbat>; + bus-width = <4>; + cd-gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* gpio 110 */ + status = "okay"; +}; + +&dss { + status = "okay"; +}; + +&hdmi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dss_hdmi_pins>; + vdda-supply = <&vdac>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap4-var-som-om44.dtsi b/arch/arm/boot/dts/omap4-var-som-om44.dtsi new file mode 100644 index 000000000000..3ae70479ae26 --- /dev/null +++ b/arch/arm/boot/dts/omap4-var-som-om44.dtsi @@ -0,0 +1,343 @@ +/* + * Copyright (C) 2014 Joachim Eastwood <manabian@xxxxxxxxx> + * Copyright (C) 2012 Variscite Ltd. - http://www.variscite.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include "omap4460.dtsi" + +/ { + model = "Variscite VAR-SOM-OM44"; + compatible = "variscite,var-som-om44", "ti,omap4430", "ti,omap4"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x40000000>; /* 1 GB */ + }; + + sound: sound { + compatible = "ti,abe-twl6040"; + ti,model = "VAR-SOM-OM44"; + + ti,mclk-freq = <38400000>; + ti,mcpdm = <&mcpdm>; + ti,twl6040 = <&twl6040>; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "AFML", "Line In", + "AFMR", "Line In"; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb1_phy_clk_pins + &hsusbb1_phy_rst_pins + >; + + reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>; /* gpio 177 */ + vcc-supply = <&vbat>; + + clocks = <&auxclk3_ck>; + clock-names = "main_clk"; + clock-frequency = <19200000>; + }; + + vbat: fixedregulator-vbat { + compatible = "regulator-fixed"; + regulator-name = "VBAT"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&omap4_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb1_pins + >; + + twl6040_pins: pinmux_twl6040_pins { + pinctrl-single,pins = < + 0x15c (PIN_OUTPUT | MUX_MODE3) /* fref_clk2_out.gpio_182 */ + 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ + >; + }; + + mcpdm_pins: pinmux_mcpdm_pins { + pinctrl-single,pins = < + 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ + 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ + 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ + 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ + 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + >; + }; + + tsc2004_pins: pinmux_tsc2004_pins { + pinctrl-single,pins = < + 0x50 (PIN_INPUT | MUX_MODE3) /* gpmc_ncs4.gpio_101 (irq) */ + 0x52 (PIN_OUTPUT | MUX_MODE3) /* gpmc_ncs5.gpio_102 (rst) */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */ + 0x102 (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */ + 0x104 (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + 0x106 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + hsusbb1_pins: pinmux_hsusbb1_pins { + pinctrl-single,pins = < + 0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */ + 0x84 (PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */ + 0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */ + 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */ + 0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */ + 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */ + 0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */ + 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */ + 0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */ + 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */ + 0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */ + 0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */ + >; + }; + + hsusbb1_phy_rst_pins: pinmux_hsusbb1_phy_rst_pins { + pinctrl-single,pins = < + 0x14c (PIN_OUTPUT | MUX_MODE3) /* kpd_row2.gpio_177 */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0xa2 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + 0xa4 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + 0xa6 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + 0xa8 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + 0xaa (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + 0xac (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; +}; + +&omap4_pmx_wkup { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb1_hub_rst_pins + &lan7500_rst_pins + >; + + hsusbb1_phy_clk_pins: pinmux_hsusbb1_phy_clk_pins { + pinctrl-single,pins = < + 0x18 (PIN_OUTPUT | MUX_MODE0) /* fref_clk3_out */ + >; + }; + + hsusbb1_hub_rst_pins: pinmux_hsusbb1_hub_rst_pins { + pinctrl-single,pins = < + 0x2 (PIN_OUTPUT | MUX_MODE3) /* gpio_wk1 */ + >; + }; + + lan7500_rst_pins: pinmux_lan7500_rst_pins { + pinctrl-single,pins = < + 0x0 (PIN_OUTPUT | MUX_MODE3) /* gpio_wk0 */ + >; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + status = "okay"; + + clock-frequency = <400000>; + + twl: twl@48 { + reg = <0x48>; + /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-parent = <&gic>; + }; + + twl6040: twl@4b { + compatible = "ti,twl6040"; + reg = <0x4b>; + + pinctrl-names = "default"; + pinctrl-0 = <&twl6040_pins>; + + /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ + interrupt-parent = <&gic>; + ti,audpwron-gpio = <&gpio6 22 0>; /* gpio 182 */ + + vio-supply = <&v1v8>; + v2v1-supply = <&v2v1>; + enable-active-high; + }; +}; + +#include "twl6030.dtsi" +#include "twl6030_omap4.dtsi" + +&vusim { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; +}; + +&i2c2 { + status = "disabled"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + status = "okay"; + + clock-frequency = <400000>; + + tsc2004@48 { + compatible = "ti,tsc2004"; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2004_pins>; + reg = <0x48>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; /* gpio 101 */ + status = "disabled"; + }; + + tmp105@49 { + compatible = "ti,tmp105"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "microchip,24c32"; + reg = <0x50>; + }; +}; + +&i2c4 { + status = "disabled"; +}; + +&mcpdm { + pinctrl-names = "default"; + pinctrl-0 = <&mcpdm_pins>; + status = "okay"; +}; + +&gpmc { + status = "disabled"; +}; + +&mcspi1 { + status = "disabled"; +}; + +&mcspi2 { + status = "disabled"; +}; + +&mcspi3 { + status = "disabled"; +}; + +&mcspi4 { + status = "disabled"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc>; + bus-width = <4>; + ti,non-removable; + status = "okay"; +}; + +&mmc2 { + status = "disabled"; +}; + +&mmc3 { + status = "disabled"; +}; + +&mmc4 { + status = "disabled"; +}; + +&mmc5 { + status = "disabled"; +}; + +&uart1 { + status = "disabled"; +}; + +&uart2 { + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "okay"; +}; + +&uart4 { + status = "disabled"; +}; + +&keypad { + status = "disabled"; +}; + +&twl_usb_comparator { + usb-supply = <&vusb>; +}; + +&usb_otg_hs { + interface-type = <1>; + mode = <3>; + power = <50>; +}; + +&usbhshost { + port1-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +}; diff --git a/arch/arm/boot/dts/omap4-var-som.dts b/arch/arm/boot/dts/omap4-var-som.dts deleted file mode 100644 index b41269e871dd..000000000000 --- a/arch/arm/boot/dts/omap4-var-som.dts +++ /dev/null @@ -1,96 +0,0 @@ -/* - * Copyright (C) 2012 Variscite Ltd. - http://www.variscite.com - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -/dts-v1/; - -#include "omap443x.dtsi" - -/ { - model = "Variscite OMAP4 SOM"; - compatible = "var,omap4-var_som", "ti,omap4430", "ti,omap4"; - - memory { - device_type = "memory"; - reg = <0x80000000 0x40000000>; /* 1 GB */ - }; - - vdd_eth: fixedregulator@0 { - compatible = "regulator-fixed"; - regulator-name = "VDD_ETH"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - enable-active-high; - regulator-boot-on; - }; -}; - -&i2c1 { - clock-frequency = <400000>; - - twl: twl@48 { - reg = <0x48>; - /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ - interrupt-parent = <&gic>; - }; -}; - -#include "twl6030.dtsi" - -&i2c2 { - clock-frequency = <400000>; -}; - -&i2c3 { - clock-frequency = <400000>; - - /* - * Temperature Sensor - * http://www.ti.com/lit/ds/symlink/tmp105.pdf - */ - tmp105@49 { - compatible = "ti,tmp105"; - reg = <0x49>; - }; -}; - -&i2c4 { - clock-frequency = <400000>; -}; - -&mcspi1 { - eth@0 { - compatible = "ks8851"; - spi-max-frequency = <24000000>; - reg = <0>; - interrupt-parent = <&gpio6>; - interrupts = <11 IRQ_TYPE_LEVEL_LOW>; /* gpio line 171 */ - vdd-supply = <&vdd_eth>; - }; -}; - -&mmc1 { - vmmc-supply = <&vmmc>; - ti,bus-width = <8>; - ti,non-removable; -}; - -&mmc2 { - status = "disabled"; -}; - -&mmc3 { - status = "disabled"; -}; - -&mmc4 { - status = "disabled"; -}; - -&mmc5 { - ti,bus-width = <4>; -}; diff --git a/arch/arm/boot/dts/omap4-var-stk-om44.dts b/arch/arm/boot/dts/omap4-var-stk-om44.dts new file mode 100644 index 000000000000..35e2364374f7 --- /dev/null +++ b/arch/arm/boot/dts/omap4-var-stk-om44.dts @@ -0,0 +1,16 @@ +/* + * Copyright (C) 2014 Joachim Eastwood <manabian@xxxxxxxxx> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap4-var-som-om44.dtsi" +#include "omap4-var-om44customboard.dtsi" + +/ { + model = "Variscite VAR-STK-OM44"; + compatible = "variscite,var-stk-om44", "variscite,var-som-om44", "ti,omap4430", "ti,omap4"; +}; -- 1.8.0 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
