Hey
On 21/02/2014 2:14 p.m., Felipe Balbi wrote:
Hi,
(please avoid top-posting)
On Fri, Feb 21, 2014 at 12:11:40AM +0000, Chris Kimber wrote:
Hey,
Thanks for the response.
I've disabled the DMA (CONFIG_MUSB_PIO_ONLY=y) but the problem still
persists (for both USB sticks & USB serial ports).
hmm, that's weird.
Now it looks like dsps_interrupt() never fires and causes the hang
up...
[ 94.865635] tty ttyUSB0: serial_write - 11 byte(s)
[ 94.865656] cp210x ttyUSB0: usb_serial_generic_write_start - length = 11, data = 54 45 53 54 49 4e 47 20 34 32 0a
[ 94.865680] musb-hdrc musb-hdrc.1.auto: qh ce461a00 periodic slot 10
[ 94.865700] musb-hdrc musb-hdrc.1.auto: qh ce461a00 urb ce481e80 dev2 ep1out-bulk, hw_ep 10, ce43db00/11
[ 94.865721] musb-hdrc musb-hdrc.1.auto: --> hw10 urb ce481e80 spd2 dev2 ep1out h_addr00 h_port00 bytes 11
[ 94.865740] musb-hdrc musb-hdrc.1.auto: TX ep10 fifo d0832c48 count 11 buf ce43db00
[ 94.865755] musb-hdrc musb-hdrc.1.auto: Start TX10 pio
[ 94.865792] musb-hdrc musb-hdrc.1.auto: usbintr (0) epintr(400)
[ 94.865810] musb-hdrc musb-hdrc.1.auto: ** IRQ host usb0000 tx0400 rx0000
[ 94.865826] musb-hdrc musb-hdrc.1.auto: OUT/TX10 end, csr 2100
[ 94.865866] musb-hdrc musb-hdrc.1.auto: complete ce481e80 usb_serial_generic_write_bulk_callback+0x0/0xd4 [usbserial] (0), dev2 ep1out, 11/11
so the first one completed just fine.
[ 94.865971] tty ttyUSB0: serial_write - 11 byte(s)
[ 94.865991] cp210x ttyUSB0: usb_serial_generic_write_start - length = 11, data = 54 45 53 54 49 4e 47 20 34 33 0a
[ 94.866015] musb-hdrc musb-hdrc.1.auto: qh ce461a00 periodic slot 10
[ 94.866035] musb-hdrc musb-hdrc.1.auto: qh ce461a00 urb ce481e80 dev2 ep1out-bulk, hw_ep 10, ce43db00/11
[ 94.866055] musb-hdrc musb-hdrc.1.auto: --> hw10 urb ce481e80 spd2 dev2 ep1out h_addr00 h_port00 bytes 11
[ 94.866075] musb-hdrc musb-hdrc.1.auto: TX ep10 fifo d0832c48 count 11 buf ce43db00
[ 94.866089] musb-hdrc musb-hdrc.1.auto: Start TX10 pio
can you dump TXCSR, DEVCTL and IRQ registers when this happens ?
I added the IRQ registers to the debugfs interface..
IntrTX : 0000
IntrRX : 0000
IntrTXE : ffff
IntrRXE : fffe
IntrUSB : 08
IntrUSBE : f7
TxCSRp : 0000
DevCtl : 5d
Oddly the VBUSERR bit is set, if I disconnect the USB cable then it goes
to 0. I just tried plugging in via powered hub and that doesn't change
the status.
Chris
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html