Hi Tomi,
On Mon, Dec 9, 2013 at 1:06 PM, Tomi Valkeinen <tomi.valkeinen@xxxxxx> wrote:
> On 2013-12-06 10:41, Javier Martinez Canillas wrote:
>> Hi Tomi,
>>
>> On Wed, Dec 4, 2013 at 1:28 PM, Tomi Valkeinen <tomi.valkeinen@xxxxxx> wrote:
>>> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@xxxxxx>
>>> ---
>>> arch/arm/boot/dts/omap3-beagle.dts | 67 ++++++++++++++++++++++++++++++++++++++
>>> 1 file changed, 67 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
>>> index fa532aaacc68..1ca1932d02aa 100644
>>> --- a/arch/arm/boot/dts/omap3-beagle.dts
>>> +++ b/arch/arm/boot/dts/omap3-beagle.dts
>>> @@ -178,3 +178,70 @@
>>> mode = <3>;
>>> power = <50>;
>>> };
>>> +
>>> +&dpi {
>>> + vdds_dsi-supply = <&vpll2>;
>>> +
>>> + dpi_out: endpoint {
>>> + remote-endpoint = <&tfp410_in>;
>>> + data-lines = <24>;
>>> + };
>>> +};
>>> +
>>> +&venc {
>>> + vdda_dac-supply = <&vdac>;
>>> +
>>> + venc_out: endpoint {
>>> + remote-endpoint = <&tv_connector_in>;
>>> + };
>>> +};
>>> +
>>> +/ {
>>> + aliases {
>>> + display0 = &dvi0;
>>> + display1 = &tv0;
>>> + };
>>> +
>>> + tfp410: encoder@0 {
>>> + compatible = "ti,tfp410";
>>> + gpios = <&gpio5 10 0>; /* 170, power-down */
>>> +
>>
>> Shouldn't this be gpio6 instead since OMAP GPIO banks start counting
>> from 1 so gpio5 + 10 is GPIO 138.
>
> Yes, you're right. Good catch.
>
>>> + ports {
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + port@0 {
>>> + reg = <0>;
>>> +
>>> + tfp410_in: endpoint@0 {
>>> + remote-endpoint = <&dpi_out>;
>>> + };
>>> + };
>>> +
>>> + port@1 {
>>> + reg = <1>;
>>> +
>>> + tfp410_out: endpoint@1 {
>>> + remote-endpoint = <&dvi_connector_in>;
>>> + };
>>> + };
>>> + };
>>> + };
>>> +
>>> + dvi0: connector@0 {
>>> + compatible = "ti,dvi_connector";
>>> + i2c-bus = <&i2c3>;
>>> +
>>> + dvi_connector_in: endpoint {
>>> + remote-endpoint = <&tfp410_out>;
>>> + };
>>> + };
>>> +
>>> + tv0: connector@1 {
>>> + compatible = "ti,svideo_connector";
>>> +
>>> + tv_connector_in: endpoint {
>>> + remote-endpoint = <&venc_out>;
>>> + };
>>> + };
>>> +};
>>> --
>>> 1.8.3.2
>>>
>>
>> Also I don't see the DSS pinmux set for this board. I guess you need
>> something like the following on top:
>>
>> 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
>> 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
>> 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
>> 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
>> 0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */
>> 0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */
>> 0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */
>> 0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */
>> 0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */
>> 0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */
>> 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
>> 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
>> 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
>> 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
>> 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
>> 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
>> 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
>> 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
>> 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
>> 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
>> 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
>> 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
>> 0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */
>> 0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */
>> 0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */
>> 0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */
>> 0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */
>> 0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */
>
> True. I need to add something like this to all the dts files.
>
> You didn't have muxing in the omap3-igep0020 patch you gave. Is the
> muxing already set in some other patch?
>
Your patch-set is based on v3.13-rc1 but I sent a patch-set [0] to fix
a few regressions for IGEPv2 when we moved to DT-only boot. One of
these patches added the needed DSS pinmuxing and these were included
in v3.13-rc2.
So to test your branch I cherry-picked:
d526daeb ("ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices")
50592dc3 ("ARM: dts: omap3-igep0020: Add pinmuxing for DVI output")
Also, for 3.13 I added a DT hack to make dpi_init_regulator() succeed
and find the VDDS_DSI regulator. That patch is mainline comit
2f2befd82 ("ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi")
Now that I think about it, you may want to add a revert for that patch
on your series too since this hack is not needed anymore with your DSS
bindings.
> Tomi
>
Thanks a lot and best regards,
Javier
>
[0]: http://www.spinics.net/lists/linux-omap/msg99970.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
