Re: [PATCH 18/26] ARM: omap3-beagle.dts: add display information

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2013-12-06 10:41, Javier Martinez Canillas wrote:
> Hi Tomi,
> 
> On Wed, Dec 4, 2013 at 1:28 PM, Tomi Valkeinen <tomi.valkeinen@xxxxxx> wrote:
>> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@xxxxxx>
>> ---
>>  arch/arm/boot/dts/omap3-beagle.dts | 67 ++++++++++++++++++++++++++++++++++++++
>>  1 file changed, 67 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
>> index fa532aaacc68..1ca1932d02aa 100644
>> --- a/arch/arm/boot/dts/omap3-beagle.dts
>> +++ b/arch/arm/boot/dts/omap3-beagle.dts
>> @@ -178,3 +178,70 @@
>>         mode = <3>;
>>         power = <50>;
>>  };
>> +
>> +&dpi {
>> +       vdds_dsi-supply = <&vpll2>;
>> +
>> +       dpi_out: endpoint {
>> +               remote-endpoint = <&tfp410_in>;
>> +               data-lines = <24>;
>> +       };
>> +};
>> +
>> +&venc {
>> +       vdda_dac-supply = <&vdac>;
>> +
>> +       venc_out: endpoint {
>> +               remote-endpoint = <&tv_connector_in>;
>> +       };
>> +};
>> +
>> +/ {
>> +       aliases {
>> +               display0 = &dvi0;
>> +               display1 = &tv0;
>> +       };
>> +
>> +       tfp410: encoder@0 {
>> +               compatible = "ti,tfp410";
>> +               gpios = <&gpio5 10 0>;  /* 170, power-down */
>> +
> 
> Shouldn't this be gpio6 instead since OMAP GPIO banks start counting
> from 1 so gpio5 + 10 is GPIO 138.

Yes, you're right. Good catch.

>> +               ports {
>> +                       #address-cells = <1>;
>> +                       #size-cells = <0>;
>> +
>> +                       port@0 {
>> +                               reg = <0>;
>> +
>> +                               tfp410_in: endpoint@0 {
>> +                                       remote-endpoint = <&dpi_out>;
>> +                               };
>> +                       };
>> +
>> +                       port@1 {
>> +                               reg = <1>;
>> +
>> +                               tfp410_out: endpoint@1 {
>> +                                       remote-endpoint = <&dvi_connector_in>;
>> +                               };
>> +                       };
>> +               };
>> +       };
>> +
>> +       dvi0: connector@0 {
>> +               compatible = "ti,dvi_connector";
>> +               i2c-bus = <&i2c3>;
>> +
>> +               dvi_connector_in: endpoint {
>> +                       remote-endpoint = <&tfp410_out>;
>> +               };
>> +       };
>> +
>> +       tv0: connector@1 {
>> +               compatible = "ti,svideo_connector";
>> +
>> +               tv_connector_in: endpoint {
>> +                       remote-endpoint = <&venc_out>;
>> +               };
>> +       };
>> +};
>> --
>> 1.8.3.2
>>
> 
> Also I don't see the DSS pinmux set for this board. I guess you need
> something like the following on top:
> 
> 0x0a4 (PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
> 0x0a6 (PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
> 0x0a8 (PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
> 0x0aa (PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
> 0x0ac (PIN_OUTPUT | MUX_MODE0)   /* dss_data0.dss_data0 */
> 0x0ae (PIN_OUTPUT | MUX_MODE0)   /* dss_data1.dss_data1 */
> 0x0b0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data2.dss_data2 */
> 0x0b2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data3.dss_data3 */
> 0x0b4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data4.dss_data4 */
> 0x0b6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data5.dss_data5 */
> 0x0b8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
> 0x0ba (PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
> 0x0bc (PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
> 0x0be (PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
> 0x0c0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
> 0x0c2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
> 0x0c4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
> 0x0c6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
> 0x0c8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
> 0x0ca (PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
> 0x0cc (PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
> 0x0ce (PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
> 0x0d0 (PIN_OUTPUT | MUX_MODE0)   /* dss_data18.dss_data18 */
> 0x0d2 (PIN_OUTPUT | MUX_MODE0)   /* dss_data19.dss_data19 */
> 0x0d4 (PIN_OUTPUT | MUX_MODE0)   /* dss_data20.dss_data20 */
> 0x0d6 (PIN_OUTPUT | MUX_MODE0)   /* dss_data21.dss_data21 */
> 0x0d8 (PIN_OUTPUT | MUX_MODE0)   /* dss_data22.dss_data22 */
> 0x0da (PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */

True. I need to add something like this to all the dts files.

You didn't have muxing in the omap3-igep0020 patch you gave. Is the
muxing already set in some other patch?

 Tomi


Attachment: signature.asc
Description: OpenPGP digital signature


[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux