RE: [PATCH 1/1] OMAP3 EVM MMC1 support for TPS based PR785 power modules

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

I believe I didn't receive any comments on this patch. Pls let me know if 
any comments are there for this patch.

Regards
Manikandan

-----Original Message-----
From: Pillai, Manikandan 
Sent: Wednesday, December 17, 2008 5:04 PM
To: linux-omap@xxxxxxxxxxxxxxx
Cc: Pillai, Manikandan
Subject: [PATCH 1/1] OMAP3 EVM MMC1 support for TPS based PR785 power modules

Resending patches after fixing comments
This patch allows the MMC1 support on OMAP2 EVM board with
TPS6235x based PR785 boards. Files mmc-pr785.* contain the
drivers. Card detect interrupt level issue has been fixed.

Signed-off-by: Manikandan Pillai <mani.pillai@xxxxxx>
---
 arch/arm/mach-omap2/Makefile         |    9 +-
 arch/arm/mach-omap2/board-omap3evm.c |   39 ++++
 arch/arm/mach-omap2/mmc-pr785.c      |  318 ++++++++++++++++++++++++++++++++++
 arch/arm/mach-omap2/mmc-pr785.h      |   38 ++++
 drivers/mmc/host/omap_hsmmc.c        |    2 +-
 5 files changed, 404 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/mach-omap2/mmc-pr785.c
 create mode 100644 arch/arm/mach-omap2/mmc-pr785.h

diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 3897347..f47ed1d 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -56,10 +56,17 @@ obj-$(CONFIG_MACH_OMAP_3430SDP)		+= board-3430sdp.o \
 					   usb-ehci.o \
 					   board-3430sdp-flash.o
 obj-$(CONFIG_MACH_OMAP3EVM)		+= board-omap3evm.o \
-					   mmc-twl4030.o \
 					   usb-musb.o usb-ehci.o \
 					   board-omap3evm-flash.o \
 					   twl4030-generic-scripts.o
+ifeq ($(CONFIG_OMAP3EVM_PR785),y)
+obj-$(CONFIG_MACH_OMAP3EVM)             += mmc-pr785.o
+endif
+ifeq ($(CONFIG_TWL4030_CORE),y)
+obj-$(CONFIG_MACH_OMAP3EVM)             += mmc-twl4030.o
+endif
+
+
 obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o \
 					   usb-musb.o usb-ehci.o \
 					   mmc-twl4030.o \
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 1aababc..db8e69e 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -36,10 +36,16 @@
 #include <mach/usb-ehci.h>
 #include <mach/common.h>
 #include <mach/mcspi.h>
+#include <mach/mux.h>
 
 #include "sdram-micron-mt46h32m32lf-6.h"
 #include "twl4030-generic-scripts.h"
+#if defined(CONFIG_TWL4030_CORE)
 #include "mmc-twl4030.h"
+#endif
+#if defined(CONFIG_OMAP3EVM_PR785)
+#include "mmc-pr785.h"
+#endif
 #include <linux/regulator/machine.h>
 #include <linux/regulator/driver.h>
 
@@ -351,6 +357,19 @@ static struct platform_device *omap3_evm_devices[] __initdata = {
 	&omap3evm_smc911x_device,
 };
 
+#if defined(CONFIG_OMAP3EVM_PR785)
+static struct pr785_hsmmc_info mmc[] __initdata = {
+	{
+		.mmc		= 1,
+		.wires		= 4,
+		.gpio_cd	= 140,
+		.gpio_wp	= -EINVAL,
+	},
+	{}	/* Terminator */
+};
+#endif
+
+#if defined(CONFIG_TWL4030_CORE)
 static struct twl4030_hsmmc_info mmc[] __initdata = {
 	{
 		.mmc		= 1,
@@ -360,6 +379,20 @@ static struct twl4030_hsmmc_info mmc[] __initdata = {
 	},
 	{}	/* Terminator */
 };
+#endif
+
+static void omap_init_pr785(void)
+{
+	/* Initialize the mux settings for PR785 power module board */
+	if (cpu_is_omap343x()) {
+		omap_cfg_reg(AF26_34XX_GPIO0);
+		omap_cfg_reg(AF22_34XX_GPIO9);
+		omap_cfg_reg(AF6_34XX_GPIO140_UP);
+		omap_cfg_reg(AE6_34XX_GPIO141);
+		omap_cfg_reg(AF5_34XX_GPIO142);
+		omap_cfg_reg(AE5_34XX_GPIO143);
+	}
+}
 
 static void __init omap3_evm_init(void)
 {
@@ -373,7 +406,13 @@ static void __init omap3_evm_init(void)
 				ARRAY_SIZE(omap3evm_spi_board_info));
 
 	omap_serial_init();
+#if defined(CONFIG_TWL4030_CORE)
 	twl4030_mmc_init(mmc);
+#endif
+#if defined(CONFIG_OMAP3EVM_PR785)
+	omap_init_pr785();
+	pr785_hsmmc_init(mmc);
+#endif
 	usb_musb_init();
 	usb_ehci_init();
 	omap3evm_flash_init();
diff --git a/arch/arm/mach-omap2/mmc-pr785.c b/arch/arm/mach-omap2/mmc-pr785.c
new file mode 100644
index 0000000..39b352a
--- /dev/null
+++ b/arch/arm/mach-omap2/mmc-pr785.c
@@ -0,0 +1,318 @@
+/*
+ * linux/arch/arm/mach-omap2/mmc-pr785.c
+ *
+ * Copyright (C) 2007-2008 Texas Instruments
+ * Author:
+ * 	Manikandan Pillai <mani.pillai@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+
+#include <mach/hardware.h>
+#include <mach/control.h>
+#include <mach/mmc.h>
+#include <mach/board.h>
+
+#include "mmc-pr785.h"
+
+#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
+
+#define	VMMC1_DEV_GRP		0x27
+#define	VMMC1_DEDICATED		0x2A
+
+#define	VMMC2_DEV_GRP		0x2B
+#define	VMMC2_DEDICATED		0x2E
+
+static u16 control_pbias_offset;
+
+#define	HSMMC_NAME_LEN		9
+
+static struct pr785_mmc_controller {
+	struct		omap_mmc_platform_data	*mmc;
+	u32		devconf_loopback_clock;
+	u16		control_devconf_offset;
+	u8		pr785_vmmc_dev_grp;
+	u8		pr785_mmc_dedicated;
+	char		name[HSMMC_NAME_LEN];
+} hsmmc[] = {
+	{
+		.control_devconf_offset		= OMAP2_CONTROL_DEVCONF0,
+		.devconf_loopback_clock		= OMAP2_MMCSDIO1ADPCLKISEL,
+		.pr785_vmmc_dev_grp		= VMMC1_DEV_GRP,
+		.pr785_mmc_dedicated		= VMMC1_DEDICATED,
+	},
+	{
+		/* control_devconf_offset set dynamically */
+		.devconf_loopback_clock		= OMAP2_MMCSDIO2ADPCLKISEL,
+		.pr785_vmmc_dev_grp		= VMMC2_DEV_GRP,
+		.pr785_mmc_dedicated		= VMMC2_DEDICATED,
+	},
+};
+
+static int pr785_mmc_card_detect(int irq)
+{
+	unsigned i;
+
+	for (i = 0; i < ARRAY_SIZE(hsmmc); i++) {
+		struct omap_mmc_platform_data *mmc;
+
+		mmc = hsmmc[i].mmc;
+		if (!mmc)
+			continue;
+		if (irq != mmc->slots[0].card_detect_irq)
+			continue;
+
+		/* NOTE: assumes card detect signal is active-low */
+		return !gpio_get_value_cansleep(mmc->slots[0].switch_pin);
+	}
+	return -ENOSYS;
+}
+
+/*
+ * Write protect pin is not supported
+ * The function below is a place holder
+*/
+static int pr785_mmc_get_ro(struct device *dev, int slot)
+{
+	struct omap_mmc_platform_data *mmc = dev->platform_data;
+
+	/* NOTE: assumes write protect signal is active-high */
+	return gpio_get_value_cansleep(mmc->slots[0].gpio_wp);
+}
+
+/*
+ * MMC late Initialization.
+ */
+static int pr785_mmc_late_init(struct device *dev)
+{
+	struct omap_mmc_platform_data *mmc = dev->platform_data;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(hsmmc); i++) {
+		if (hsmmc[i].name == mmc->slots[0].name) {
+			hsmmc[i].mmc = mmc;
+			break;
+		}
+	}
+	return 0;
+}
+
+static void pr785_mmc_cleanup(struct device *dev)
+{
+	/* nothing to cleanup */
+	gpio_free(OMAP_PR785_MMC1_CD);
+	return;
+}
+
+#ifdef CONFIG_PM
+
+static int pr785_mmc_suspend(struct device *dev, int slot)
+{
+	struct omap_mmc_platform_data *mmc = dev->platform_data;
+
+	disable_irq(mmc->slots[0].card_detect_irq);
+	return 0;
+}
+
+static int pr785_mmc_resume(struct device *dev, int slot)
+{
+	struct omap_mmc_platform_data *mmc = dev->platform_data;
+
+	enable_irq(mmc->slots[0].card_detect_irq);
+	return 0;
+}
+
+#else
+#define pr785_mmc_suspend	NULL
+#define pr785_mmc_resume	NULL
+#endif
+
+/*
+ * Sets the MMC voltage
+ * The MMC voltage on PR785 can only be set to 3.15 V due to hardware bug
+ */
+static int pr785_mmc_set_voltage(struct pr785_mmc_controller *c, int vdd)
+{
+	if (vdd)
+		gpio_direction_output(OMAP_PR785_MMC1_VSET, 1);
+	else
+		gpio_direction_output(OMAP_PR785_MMC1_VSET, 0);
+	return 0;
+}
+
+static int pr785_mmc1_set_power(struct device *dev, int slot, int power_on,
+				int vdd)
+{
+	u32 reg;
+	int ret = 0;
+	struct pr785_mmc_controller *c = &hsmmc[0];
+
+	if (power_on) {
+		if (cpu_is_omap2430()) {
+			reg = omap_ctrl_readl(OMAP243X_CONTROL_DEVCONF1);
+			if ((1 << vdd) >= MMC_VDD_30_31)
+				reg |= OMAP243X_MMC1_ACTIVE_OVERWRITE;
+			else
+				reg &= ~OMAP243X_MMC1_ACTIVE_OVERWRITE;
+			omap_ctrl_writel(reg, OMAP243X_CONTROL_DEVCONF1);
+		}
+
+		/* REVISIT: Loop back clock not needed for 2430? */
+		if (!cpu_is_omap2430()) {
+			reg = omap_ctrl_readl(c->control_devconf_offset);
+			reg |= OMAP2_MMCSDIO1ADPCLKISEL;
+			omap_ctrl_writel(reg, c->control_devconf_offset);
+		}
+
+		reg = omap_ctrl_readl(control_pbias_offset);
+		reg |= OMAP2_PBIASSPEEDCTRL0;
+		reg &= ~OMAP2_PBIASLITEPWRDNZ0;
+		omap_ctrl_writel(reg, control_pbias_offset);
+
+		ret = pr785_mmc_set_voltage(c, vdd);
+
+		/* 100ms delay required for PBIAS configuration */
+		msleep(100);
+		reg = omap_ctrl_readl(control_pbias_offset);
+		reg |= (OMAP2_PBIASLITEPWRDNZ0 | OMAP2_PBIASSPEEDCTRL0);
+		if ((1 << vdd) <= MMC_VDD_165_195)
+			reg &= ~OMAP2_PBIASLITEVMODE0;
+		else
+			reg |= OMAP2_PBIASLITEVMODE0;
+		omap_ctrl_writel(reg, control_pbias_offset);
+	} else {
+		reg = omap_ctrl_readl(control_pbias_offset);
+		reg &= ~OMAP2_PBIASLITEPWRDNZ0;
+		omap_ctrl_writel(reg, control_pbias_offset);
+
+		ret = pr785_mmc_set_voltage(c, 0);
+
+		/* 100ms delay required for PBIAS configuration */
+		msleep(100);
+		reg = omap_ctrl_readl(control_pbias_offset);
+		reg |= (OMAP2_PBIASSPEEDCTRL0 | OMAP2_PBIASLITEPWRDNZ0 |
+			OMAP2_PBIASLITEVMODE0);
+		omap_ctrl_writel(reg, control_pbias_offset);
+	}
+
+	return ret;
+}
+
+static int pr785_mmc2_set_power(struct device *dev, int slot,
+				int power_on, int vdd)
+{
+	/* MMC2 is not available on OMAP3 EVM */
+	return 0;
+}
+
+static struct omap_mmc_platform_data *hsmmc_data[OMAP34XX_NR_MMC] __initdata;
+
+void __init pr785_hsmmc_init(struct pr785_hsmmc_info *controllers)
+{
+	struct pr785_hsmmc_info *c;
+	int nr_hsmmc = ARRAY_SIZE(hsmmc_data);
+
+	if (cpu_is_omap2430()) {
+		control_pbias_offset = OMAP243X_CONTROL_PBIAS_LITE;
+		hsmmc[1].control_devconf_offset = OMAP243X_CONTROL_DEVCONF1;
+		nr_hsmmc = 2;
+	} else {
+		control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
+		hsmmc[1].control_devconf_offset = OMAP343X_CONTROL_DEVCONF1;
+	}
+
+#if defined(CONFIG_MACH_OMAP3EVM) && defined(CONFIG_OAMP3EVM_PR785)
+	/* setup the GPIO for MMC for PR785 Rev ES2 power module */
+	/* Setup GPIO 0 - MMC1_VSET */
+	gpio_direction_output(OMAP_PR785_MMC1_VSET, 1);
+	/* Setup GPIO 9 - MMC1_EN */
+	gpio_direction_output(OMAP_PR785_MMC1_EN, 1);
+
+	/* Setup GPIO 140 - MMC1_CD as input */
+	if (gpio_request(OMAP_PR785_MMC1_CD, "AF6_34XX_GPIO140_UP") < 0) {
+		printk(KERN_ERR "Failed to request MMC IRQ %d \n",
+			OMAP_PR785_MMC1_CD);
+		return -1;
+	}
+	gpio_direction_input(OMAP_PR785_MMC1_CD);
+#endif
+
+
+	for (c = controllers; c->mmc; c++) {
+		struct pr785_mmc_controller *pr785 = hsmmc + c->mmc - 1;
+		struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1];
+
+		if (!c->mmc || c->mmc > nr_hsmmc) {
+			pr_debug("MMC%d: no such controller\n", c->mmc);
+			continue;
+		}
+		if (mmc) {
+			pr_debug("MMC%d: already configured\n", c->mmc);
+			continue;
+		}
+
+		mmc = kzalloc(sizeof(struct omap_mmc_platform_data),
+				GFP_KERNEL);
+		if (!mmc) {
+			pr_err("Cannot allocate memory for mmc device!\n");
+			return;
+		}
+
+		sprintf(pr785->name, "mmc%islot%i", c->mmc, 1);
+		mmc->slots[0].name = pr785->name;
+		mmc->nr_slots = 1;
+		mmc->slots[0].ocr_mask = MMC_VDD_165_195 |
+					MMC_VDD_26_27 | MMC_VDD_27_28 |
+					MMC_VDD_29_30 |
+					MMC_VDD_30_31 | MMC_VDD_31_32;
+		mmc->slots[0].wires = c->wires;
+		mmc->dma_mask = 0xffffffff;
+
+		if (c->gpio_cd != -EINVAL) {
+			mmc->init = pr785_mmc_late_init;
+			mmc->cleanup = pr785_mmc_cleanup;
+			mmc->suspend = pr785_mmc_suspend;
+			mmc->resume = pr785_mmc_resume;
+
+			mmc->slots[0].switch_pin = OMAP_PR785_MMC1_CD;
+			mmc->slots[0].card_detect_irq = gpio_to_irq(c->gpio_cd);
+			mmc->slots[0].card_detect = pr785_mmc_card_detect;
+		} else
+			mmc->slots[0].switch_pin = -EINVAL;
+
+		/* write protect normally uses an OMAP gpio */
+		if (c->gpio_wp != -EINVAL) {
+			gpio_request(c->gpio_wp, "mmc_wp");
+			gpio_direction_input(c->gpio_wp);
+
+			mmc->slots[0].gpio_wp = c->gpio_wp;
+			mmc->slots[0].get_ro = pr785_mmc_get_ro;
+		} else
+			mmc->slots[0].gpio_wp = -EINVAL;
+
+		switch (c->mmc) {
+		case 1:
+			mmc->slots[0].set_power = pr785_mmc1_set_power;
+			break;
+		case 2:
+			mmc->slots[0].set_power = pr785_mmc2_set_power;
+			break;
+		default:
+			pr_err("MMC%d configuration not supported!\n", c->mmc);
+			continue;
+		}
+		hsmmc_data[c->mmc - 1] = mmc;
+	}
+	omap2_init_mmc(hsmmc_data, OMAP34XX_NR_MMC);
+}
+
+#endif
diff --git a/arch/arm/mach-omap2/mmc-pr785.h b/arch/arm/mach-omap2/mmc-pr785.h
new file mode 100644
index 0000000..7178412
--- /dev/null
+++ b/arch/arm/mach-omap2/mmc-pr785.h
@@ -0,0 +1,38 @@
+/*
+ * linux/arch/arm/mach-omap2/mmc-pr785.h
+ *
+ * Copyright (C) 2007-2008 Texas Instruments
+ * Author:
+ * 	Manikandan Pillai <mani.pillai@xxxxxx>
+ *
+ * MMC definitions for OMAP2
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define	OMAP_PR785_MMC1_VSET	0
+#define	OMAP_PR785_MMC1_CD	140
+#define	OMAP_PR785_MMC1_EN      9
+#define	OMAP_PR785_MMC1_CD_MSK  ((1<<12))
+
+struct pr785_hsmmc_info {
+	u8	mmc;		/* controller 1/2/3 */
+	u8	wires;		/* 1/4/8 wires */
+	int	gpio_cd;	/* or -EINVAL */
+	int	gpio_wp;	/* or -EINVAL */
+};
+
+#if	defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \
+	defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
+
+void pr785_hsmmc_init(struct pr785_hsmmc_info *);
+
+#else
+
+static inline void pr785_hsmmc_init(struct pr785_hsmmc_info *info)
+{
+}
+
+#endif
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index c1b66ca..8d90c61 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -917,7 +917,7 @@ static int __init omap_mmc_probe(struct platform_device *pdev)
 	struct mmc_host *mmc;
 	struct mmc_omap_host *host = NULL;
 	struct resource *res;
-	int ret = 0, irq, reg;
+	int ret = 0, irq;
 	u32 hctl, capa;
 
 	if (pdata == NULL) {
-- 
1.5.6

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux