On Tue, Nov 04, 2008 at 02:35:50PM -0700, York, Jeffrey-P56387 wrote: > I am using Montavista Mobilinux 5 on OMAP2430 and I am trying to access is it 2430sdp ? Which board are you using ?? > the FSUSB register set and the kernel halts upon any attempt to access > any of the registers in the FSUSB. > > Note, under the Mobilinux distribution, the HSUSB controller is used by > default, not the FSUSB controller. I am trying to access both so that I > can have USB port 0 controlled by the HSUSB and port 1 controlled by the > FSUSB controller. in practice this shouldn't be needed actualy. upon attaching a FS device to ehci port, ehci would handoff the port to ohci. I'm not sure if that's working fine currently. > Per the TI spec, the host and device register sets within the FSUSB > controller can only be accessed if the OTG register set is correctly > configured. However, the OTG register set should be accessible as long > as there is a 48MHz clock. > > I have tried reading the OTG_REVISION register (0x4805e300) and the > OTG_SYSCON_1_REG (0x4805e304) within arch/arm/plat-omap/usb.c. Upon > either read, the kernel halts and I do not see any logs at startup after > the > "Uncompressing > Linux............................................................. > ........................................... done, booting the kernel." > message. enable CONFIG_DEBUG_LL and you might see something. I'm guessing you're gonna get unhandled page fault request (or something similar, can't remember the correct error message) which most likely means you have to enable certain clocks before reading the registers. btw, this list is for the open linux-omap.git tree. If your montavista distribution is not using the current git tree, you should probably contact montavista's support. > If I comment out the register accesses, I do see the startup log and I > see the following log statements within arch/arm/plat-omap/usb.c > "Timeout enabling clock usb_l4_ick" > "Timeout enabling clock usb_fck" what's the kernel version ?? This should be fixed a long time ago. > In addition I have printed out various register values and they are as > follows. > > Various register values: > > CM_FCLKEN2_CORE - Address:0x49006204 - value 0x001B07BF,bit 0 is 0x1, > should be 1 > > CM_ICLKEN2_CORE - Address:0x49006214 - value 0x00000FFF,bit 0 is 0x1, > should be 1 > > CM_IDLEST2_CORE - Address:0x49006224 - value 0x00000FFE,bit 0 is 0x0, > should be 1 --- Possibly this is causing my problem but it is not clear > to me what I need to do to have this set to a '1'. > > CM_AUTOIDLE2_CORE - Address:0x49006234 - value 0x00000000,bit 0 is 0x0, > should be 0 > > CM_CLKSEL1_CORE - Address:0x49006240 - value 0x02102946,bits 27-25 is > 0x1, should be 1 for L3_CLK/1 (boot mode only), 2 for L3_CLK/2, or 4 for > L3_CLK/4 > > PM_WKEN2_CORE - Address:0x490062A4 - value 0x00000000,bit 0 is 0x0, > should be 0 for disabled, 1 for enabled -- Per TI, this does not need > to be enabled... > > PM_WKST2_CORE - Address:0x490062B4 - value 0x00000000,bit 0 is 0x0, > should be 0 for not occurred, 1 for occurred > > CM_IDLEST_CKGEN - Address:0x49006520 - value 0x00000336,bit 4 is 0x1, > should be 0x1 for active 48M_CLK > > > Any ideas as to what the register settings need to be to enable access > to the FSUSB OTG registers? I'm guessing you only need to enable some clock(s). But also, please, reply with low level debug output and kernel version. Also, try out the current omap git tree. There's a defconfig for 2430sdp (omap_2430sdp_defconfig) that you might want to try. -- balbi -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
