From: David Brownell <dbrownell@xxxxxxxxxxxxxxxxxxxxx>
Request two more GPIOs on Beagle: MMC write protect, DVI enable.
Also define the first OMAP3 GPIO mux config symbols, with a new
naming convention. Examples:
- GPIO42 is bidirectional, and uses external pull up/down (if any);
- GPIO42_UP is bidirectional, with an internal pullup;
- GPIO42_DOWN is bidirectional, with an internal pulldown.
- GPIO42_OUT is output-only, and needs no pullup or pulldown.
All of those would be fully functional through the standard GPIO
interface as well as the legacy OMAP-only one, except GPIO42_OUT
which won't let you read the actual pin value after setting it.
There's no special off-mode support for these particular pins;
on Beagle they have external pullups or pulldowns.
(OMAP2 can use this naming convention too, except that since it
has no input-enable the "_OUT" convention can't be used there.)
Signed-off-by: David Brownell <dbrownell@xxxxxxxxxxxxxxxxxxxxx>
---
REFRESHED against 2.6.27-rc8-omap-git as of today ...
arch/arm/mach-omap2/board-omap3beagle.c | 11 +++++++++++
arch/arm/mach-omap2/mux.c | 8 ++++++++
arch/arm/plat-omap/include/mach/mux.h | 8 ++++++++
3 files changed, 27 insertions(+)
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -43,6 +43,7 @@
#include <mach/common.h>
#include <mach/gpmc.h>
#include <mach/nand.h>
+#include <mach/mux.h>
#define GPMC_CS0_BASE 0x60
@@ -291,7 +292,17 @@ static void __init omap3_beagle_init(voi
omap_board_config = omap3_beagle_config;
omap_board_config_size = ARRAY_SIZE(omap3_beagle_config);
omap_serial_init();
+
+ omap_cfg_reg(AH8_34XX_GPIO29);
+ gpio_request(29, "mmc0_wp");
+ gpio_direction_input(29);
hsmmc_init();
+
+ omap_cfg_reg(J25_34XX_GPIO170);
+ gpio_request(170, "DVI_nPD");
+ /* REVISIT leave DVI powered down until it's needed ... */
+ gpio_direction_output(170, true);
+
usb_musb_init();
usb_ehci_init();
omap3beagle_flash_init();
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -416,6 +416,14 @@ MUX_CFG_34XX("AD2_3430_USB3FS_PHY_MM3_TX
MUX_CFG_34XX("AC1_3430_USB3FS_PHY_MM3_TXEN_N", 0x18a,
OMAP34XX_MUX_MODE6 | OMAP34XX_PIN_OUTPUT)
+
+/* 34XX GPIO - bidirectional, unless the name has an "_OUT" suffix.
+ * No internal pullup/pulldown without "_UP" or "_DOWN" suffix.
+ */
+MUX_CFG_34XX("AH8_34XX_GPIO29", 0x5fa,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
};
#define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins)
--- a/arch/arm/plat-omap/include/mach/mux.h
+++ b/arch/arm/plat-omap/include/mach/mux.h
@@ -749,6 +749,14 @@ enum omap34xx_index {
AD2_3430_USB3FS_PHY_MM3_TXDAT,
AC1_3430_USB3FS_PHY_MM3_TXEN_N,
+ /* 34xx GPIO
+ * - normally these are bidirectional, no internal pullup/pulldown
+ * - "_UP" suffix (GPIO3_UP) if internal pullup is configured
+ * - "_DOWN" suffix (GPIO3_DOWN) with internal pulldown
+ * - "_OUT" suffix (GPIO3_OUT) for output-only pins (unlike 24xx)
+ */
+ AH8_34XX_GPIO29,
+ J25_34XX_GPIO170,
};
struct omap_mux_cfg {
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
