* Aguirre Rodriguez, Sergio Alberto <saaguirre@xxxxxx> [080829 16:35]:
> From: Sergio Aguirre <saaguirre@xxxxxx>
>
> OMAP34XX: CAM: Add Sensors Support
>
> This adds support in OMAP34xx SDP board file for Sensor and Lens
> driver.
Should this be in board-3430sdp-camera.c or something like that?
Tony
>
> Signed-off-by: Sergio Aguirre <saaguirre@xxxxxx>
> ---
> arch/arm/mach-omap2/board-3430sdp.c | 228 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 228 insertions(+)
>
> Index: linux-omap-2.6/arch/arm/mach-omap2/board-3430sdp.c
> ===================================================================
> --- linux-omap-2.6.orig/arch/arm/mach-omap2/board-3430sdp.c 2008-08-25 11:00:18.000000000 -0500
> +++ linux-omap-2.6/arch/arm/mach-omap2/board-3430sdp.c 2008-08-25 12:16:46.000000000 -0500
> @@ -42,6 +42,19 @@
> #include <mach/gpmc.h>
> #include <linux/i2c/twl4030-rtc.h>
>
> +#ifdef CONFIG_VIDEO_OMAP3
> +#include <media/v4l2-int-device.h>
> +#include <../drivers/media/video/omap34xxcam.h>
> +#include <../drivers/media/video/isp/ispreg.h>
> +#if defined(CONFIG_VIDEO_MT9P012) || defined(CONFIG_VIDEO_MT9P012_MODULE)
> +#include <../drivers/media/video/mt9p012.h>
> +#endif
> +#endif
> +
> +#ifdef CONFIG_VIDEO_DW9710
> +#include <../drivers/media/video/dw9710.h>
> +#endif
> +
> #include <asm/io.h>
> #include <asm/delay.h>
> #include <mach/control.h>
> @@ -266,6 +279,216 @@
> },
> };
>
> +#ifdef CONFIG_VIDEO_DW9710
> +static int dw9710_lens_power_set(enum v4l2_power power)
> +{
> +
> + return 0;
> +}
> +
> +static int dw9710_lens_set_prv_data(void *priv)
> +{
> + struct omap34xxcam_hw_config *hwc = priv;
> +
> + hwc->dev_index = 0;
> + hwc->dev_minor = 0;
> + hwc->dev_type = OMAP34XXCAM_SLAVE_LENS;
> +
> + return 0;
> +}
> +
> +static struct dw9710_platform_data sdp3430_dw9710_platform_data = {
> + .power_set = dw9710_lens_power_set,
> + .priv_data_set = dw9710_lens_set_prv_data,
> +};
> +#endif
> +
> +#if defined(CONFIG_VIDEO_MT9P012) || defined(CONFIG_VIDEO_MT9P012_MODULE)
> +static void __iomem *fpga_map_addr;
> +
> +static struct omap34xxcam_sensor_config cam_hwc = {
> + .sensor_isp = 0,
> + .xclk = OMAP34XXCAM_XCLK_A,
> +};
> +
> +static void enable_fpga_vio_1v8(u8 enable)
> +{
> + u16 reg_val;
> +
> + fpga_map_addr = ioremap(DEBUG_BASE, 4096);
> + reg_val = readw(fpga_map_addr + REG_SDP3430_FPGA_GPIO_2);
> +
> + /* Ensure that the SPR_GPIO1_3v3 is 0 - powered off.. 1 is on */
> + if (reg_val & FPGA_SPR_GPIO1_3v3) {
> + reg_val |= FPGA_SPR_GPIO1_3v3;
> + reg_val |= FPGA_GPIO6_DIR_CTRL; /* output mode */
> + writew(reg_val, fpga_map_addr + REG_SDP3430_FPGA_GPIO_2);
> + /* give a few milli sec to settle down
> + * Let the sensor also settle down.. if required..
> + */
> + if (enable)
> + mdelay(10);
> + }
> +
> + if (enable) {
> + reg_val |= FPGA_SPR_GPIO1_3v3 | FPGA_GPIO6_DIR_CTRL;
> + writew(reg_val, fpga_map_addr + REG_SDP3430_FPGA_GPIO_2);
> + }
> + /* Vrise time for the voltage - should be less than 1 ms */
> + mdelay(1);
> +}
> +
> +static int mt9p012_sensor_set_prv_data(void *priv)
> +{
> + struct omap34xxcam_hw_config *hwc = priv;
> +
> + hwc->u.sensor.xclk = cam_hwc.xclk;
> + hwc->u.sensor.sensor_isp = cam_hwc.sensor_isp;
> + hwc->dev_index = 0;
> + hwc->dev_minor = 0;
> + hwc->dev_type = OMAP34XXCAM_SLAVE_SENSOR;
> + return 0;
> +}
> +
> +static struct isp_interface_config mt9p012_if_config = {
> + .ccdc_par_ser = ISP_PARLL,
> + .dataline_shift = 0x1,
> + .hsvs_syncdetect = ISPCTRL_SYNC_DETECT_VSRISE,
> + .vdint0_timing = 0x0,
> + .vdint1_timing = 0x0,
> + .strobe = 0x0,
> + .prestrobe = 0x0,
> + .shutter = 0x0,
> + .u.par.par_bridge = 0x0,
> + .u.par.par_clk_pol = 0x0,
> +};
> +
> +static int mt9p012_sensor_power_set(enum v4l2_power power)
> +{
> + switch (power) {
> + case V4L2_POWER_OFF:
> + /* Power Down Sequence */
> +#ifdef CONFIG_TWL4030_CORE
> + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
> + VAUX_DEV_GRP_NONE, TWL4030_VAUX2_DEV_GRP);
> +#else
> +#error "no power companion board defined!"
> +#endif
> + enable_fpga_vio_1v8(0);
> + omap_free_gpio(MT9P012_RESET_GPIO);
> + iounmap(fpga_map_addr);
> + omap_free_gpio(MT9P012_STANDBY_GPIO);
> + break;
> + case V4L2_POWER_ON:
> + /* Power Up Sequence */
> + isp_configure_interface(&mt9p012_if_config);
> +
> + /* Request and configure gpio pins */
> + if (omap_request_gpio(MT9P012_STANDBY_GPIO) != 0) {
> + printk(KERN_WARNING "Could not request GPIO %d for "
> + "AF D88\n", MT9P012_STANDBY_GPIO);
> + return -EIO;
> + }
> +
> + /* Request and configure gpio pins */
> + if (omap_request_gpio(MT9P012_RESET_GPIO) != 0)
> + return -EIO;
> +
> + /* set to output mode */
> + omap_set_gpio_direction(MT9P012_STANDBY_GPIO, 0);
> + /* set to output mode */
> + omap_set_gpio_direction(MT9P012_RESET_GPIO, 0);
> +
> + /* STANDBY_GPIO is active HIGH for set LOW to release */
> + omap_set_gpio_dataout(MT9P012_STANDBY_GPIO, 1);
> +
> + /* nRESET is active LOW. set HIGH to release reset */
> + omap_set_gpio_dataout(MT9P012_RESET_GPIO, 1);
> +
> + /* turn on digital power */
> + enable_fpga_vio_1v8(1);
> +#ifdef CONFIG_TWL4030_CORE
> + /* turn on analog power */
> + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
> + VAUX_2_8_V, TWL4030_VAUX2_DEDICATED);
> + twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
> + VAUX_DEV_GRP_P1, TWL4030_VAUX2_DEV_GRP);
> +#else
> +#error "no power companion board defined!"
> +#endif
> +
> + omap_set_gpio_dataout(MT9P012_STANDBY_GPIO, 0);
> +
> + udelay(1000);
> +
> + /* have to put sensor to reset to guarantee detection */
> + omap_set_gpio_dataout(MT9P012_RESET_GPIO, 0);
> +
> + udelay(1500);
> +
> + /* nRESET is active LOW. set HIGH to release reset */
> + omap_set_gpio_dataout(MT9P012_RESET_GPIO, 1);
> + /* give sensor sometime to get out of the reset. Datasheet says
> + 2400 xclks. At 6 MHz, 400 usec are enough */
> + udelay(300);
> + break;
> + case V4L2_POWER_STANDBY:
> + /* stand by */
> + omap_set_gpio_dataout(MT9P012_STANDBY_GPIO, 1);
> + break;
> + case V4L2_POWER_RESUME:
> + /* out of standby */
> + omap_set_gpio_dataout(MT9P012_STANDBY_GPIO, 0);
> + udelay(1000);
> + break;
> + }
> +
> + return 0;
> +}
> +
> +static struct v4l2_ifparm ifparm = {
> + .if_type = V4L2_IF_TYPE_BT656,
> + .u = {
> + .bt656 = {
> + .frame_start_on_rising_vs = 1,
> + .latch_clk_inv = 0,
> + .mode = V4L2_IF_TYPE_BT656_MODE_NOBT_10BIT,
> + .clock_min = MT9P012_XCLK_MIN,
> + .clock_max = MT9P012_XCLK_MAX,
> + },
> + },
> +};
> +
> +static int mt9p012_ifparm(struct v4l2_ifparm *p)
> +{
> + *p = ifparm;
> + return 0;
> +}
> +
> +static struct mt9p012_platform_data sdp3430_mt9p012_platform_data = {
> + .power_set = mt9p012_sensor_power_set,
> + .priv_data_set = mt9p012_sensor_set_prv_data,
> + .default_regs = NULL,
> + .ifparm = mt9p012_ifparm,
> +};
> +
> +
> +static struct i2c_board_info __initdata sdp3430_i2c_board_info[] = {
> +#ifdef CONFIG_VIDEO_DW9710
> + {
> + I2C_BOARD_INFO(DW9710_NAME, DW9710_AF_I2C_ADDR),
> + .platform_data = &sdp3430_dw9710_platform_data,
> + },
> +#endif
> + {
> + I2C_BOARD_INFO("mt9p012", MT9P012_I2C_ADDR),
> + .platform_data = &sdp3430_mt9p012_platform_data,
> + },
> +};
> +
> +#endif
> +
> +
> static struct platform_device sdp3430_lcd_device = {
> .name = "sdp2430_lcd",
> .id = -1,
> @@ -344,7 +567,12 @@
> static int __init omap3430_i2c_init(void)
> {
> omap_register_i2c_bus(1, 2600, NULL, 0);
> +#if defined(CONFIG_VIDEO_MT9P012) || defined(CONFIG_VIDEO_MT9P012_MODULE)
> + omap_register_i2c_bus(2, 400, sdp3430_i2c_board_info,
> + ARRAY_SIZE(sdp3430_i2c_board_info));
> +#else
> omap_register_i2c_bus(2, 400, NULL, 0);
> +#endif
> omap_register_i2c_bus(3, 400, NULL, 0);
> return 0;
> }
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
