Kanagesh, You can give it a shot using a different cable - I have seen similar issues when using a faulty cable. Regards, Pratheesh -----Original Message----- From: linux-omap-owner@xxxxxxxxxxxxxxx [mailto:linux-omap-owner@xxxxxxxxxxxxxxx] On Behalf Of Gupta, Ajay Kumar Sent: Wednesday, August 06, 2008 6:12 PM To: kanagesh radhakrishnan Cc: linux-omap@xxxxxxxxxxxxxxx Subject: RE: Problems with USB Gadget on the OMAP3EVM Kanagesh, I tested it with Windows XP machine and it works all fine. I had to use linux.inf file which is at Documetation\usb\ folder. linux.inf file should have same VID/PID as reported by gadget rndis driver to host. Regards, Ajay -----Original Message----- From: linux-omap-owner@xxxxxxxxxxxxxxx [mailto:linux-omap-owner@xxxxxxxxxxxxxxx] On Behalf Of kanagesh radhakrishnan Sent: Wednesday, August 06, 2008 10:43 AM To: felipe.balbi@xxxxxxxxx Cc: linux-omap@xxxxxxxxxxxxxxx Subject: Re: Problems with USB Gadget on the OMAP3EVM On 8/5/08, Felipe Balbi <felipe.balbi@xxxxxxxxx> wrote: > Hi, > > > On Tue, Aug 05, 2008 at 04:47:02PM +0530, ext kanagesh radhakrishnan wrote: > > Running the Test > > ------------------------- > > On the OMAP3EVM Target > > ####################### > > On successful boot with this kernel on the target board, after > > plugging in the USB cable, the following messages appear on the > > console: > > > > musb_stage2_irq 863: SUSPEND (b_idle) devctl 99 power e0 > > musb_stage0_irq 722: BUS RESET > > musb_stage0_irq 722: BUS RESET > > musb_stage0_irq 722: BUS RESET > > musb_stage0_irq 722: BUS RESET > > musb_stage0_irq 722: BUS RESET > > musb_stage0_irq 722: BUS RESET > > musb_stage0_irq 722: BUS RESET > > musb_stage0_irq 722: BUS RESET > > usb0: high speed config #2: 100 mA, Ethernet Gadget, using RNDIS > > musb_stage0_irq 722: BUS RESET > > musb_stage0_irq 722: BUS RESET > > musb_stage2_irq 863: SUSPEND (b_peripheral) devctl 99 power f0 > > > > I then setup an IP address for the usb0 interface with the following command: > > > > [root@OMAP3EVM /]# /sbin/ifconfig usb0 192.168.1.1 up netmask 255.255.255.0 > > > > On the Linux Host machine > > ####################### > > > > On insertion of the USB cable, 'dmesg' shows the following messages: > > > > usb 1-2: new high speed USB device using address 3 > > usb 1-2: configuration #1 chosen from 2 choices > > usb 1-2: can't set config #1, error -71 > > > That's weird since gadget api set config 2 as your dmesg states. > > usb0: high speed config #2: 100 mA, Ethernet Gadget, using RNDIS > > > > The Problem > > ------------------- > > On an attempt to setup an IP address for the usb0 interface, I get the > > following error: > > > > usb0: unknown interface: No such device > > SIOCSIFADDR: No such device > > usb0: unknown interface: No such device > > SIOCSIFNETMASK: No such device > > SIOCGIFADDR: No such device > > SIOCSIFBROADCAST: No such device > > > Looks like the problem is in the host side usbnet.ko. What kernel > version is in your host machine ? > > > > The Test Setup > > ---------------------- > > > > Host > > #### > > Linux machine running Fedora Core 5. > > Manually loaded the module usbnet.ko. > > > Which kernel version is in this fedora core 5 ?? > > > > Target > > ##### > > OMAP3EVM running OMAP35x_SDK_0.9.8 firmware: x-load, u-boot and > > kernel (linux-2.6.22.18) > > Dip switches (SW4) set to boot from NAND flash (01010000) > > > > > > Although my end objective is to test the USB functionality with > > TWL4030 USB transceiver, I wanted to verify if USB functions as > > expected through ISP1504 transceiver on my board with the SDK_0.9.8. > > Has anyone tested the USB Gadget setup on the OMAP3EVM boards? > > > I'd strongly suggest you to try out current linux-omap code [1] and check > if it works fine. > > Also increase MUSB_LOGLEVEL to 3 in your .config file and reabuild that > 2.6.22.18 kernel. > > When you clone linux omap with: > > $ git clone http://www.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git > > You can make omap3_evm_defconfig and later make menuconfig to choose the > gadget driver you want. > > [1] http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=summary > > -- > > balbi > Hello everyone, Thank you very much for the comments and suggestions. The version of Linux kernel on the native host Fedora Core 5 machine is the default 2.6.9-1.667 kernel that comes with the FC5 release. Keeping in mind where we are, this does sound like an ancient kernel. However, I have USB networking with Gadget drivers working on this same machine with OMAP5912 OSK, OMAP2430 SDP and another custom OMAP2430 based board. Nevertheless, I decided to upgrade to a more recent version of the Linux kernel on the host system. I will test the setup once again and update the observation. Meanwhile, I tested the setup with a Windows XP host machine and these are the observations: On insertion of the USB cable to the Win XP host machine, the OMAP3EVM board gets detected as 'RNDIS/Ethernet' Device. I go through the driver installation (driver used is file Documentation/usb/linux.inf from the standard Linux kernel sources). After the installation is complete, I get an error from the Windows XP system saying "An error was encountered while installing the driver and the hardware might not function as intended" Thank you all, Regards, Kanagesh -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
