* Dirk Behme <dirk.behme@xxxxxxxxxxxxxx> [080704 10:39]:
>
> I2C2 at BeagleBoard is connected to expansion connector, i.e. unused if
> nothing is connected to this connector. As internal OMAP3 pull up
> resistors are not strong enough, enabled but unused I2C2 bus results in
> error messages (e.g. I2C timeouts). I2C2 should be enabled only if
> something is connected to I2C2 at board's expansion connector and this
> extension has additional pull up resistors for I2C2 bus.
>
> - Add configuration option for this
> - Use configuration option in board-omap3beagle
> - While being there, add OMAP3 to OMAP I2C help text
Pushing today.
Tony
> Signed-off-by: Dirk Behme <dirk.behme@xxxxxxxxx>
>
>
> Subject: ARM: OMAP3: Make I2C bus 2 configurable for BeagleBoard
>
> From: Dirk Behme <dirk.behme@xxxxxxxxx>
>
> I2C2 at BeagleBoard is connected to expansion connector, i.e. unused if
> nothing is connected to this connector. As internal OMAP3 pull up resistors
> are not strong enough, enabled but unused I2C2 bus results in error messages
> (e.g. I2C timeouts). I2C2 should be enabled only if something is connected to
> I2C2 at board's expansion connector and this extension has additional pull up
> resistors for I2C2 bus.
>
> - Add configuration option for this
> - Use configuration option in board-omap3beagle
> - While being there, add OMAP3 to OMAP I2C help text
>
> Signed-off-by: Dirk Behme <dirk.behme@xxxxxxxxx>
>
> ---
>
> Changes in v2: Incorporate Jarkko's comments. Pin mux is already done
> depending on enabled busses in omap_i2c_mux_pins(int bus).
> We don't have to do it manually here. Thanks!
>
> Index: linux-beagle/arch/arm/mach-omap2/board-omap3beagle.c
> ===================================================================
> --- linux-beagle.orig/arch/arm/mach-omap2/board-omap3beagle.c
> +++ linux-beagle/arch/arm/mach-omap2/board-omap3beagle.c
> @@ -40,7 +40,9 @@ static struct omap_uart_config omap3_bea
> static int __init omap3_beagle_i2c_init(void)
> {
> omap_register_i2c_bus(1, 2600, NULL, 0);
> +#ifdef CONFIG_I2C2_OMAP_BEAGLE
> omap_register_i2c_bus(2, 400, NULL, 0);
> +#endif
> omap_register_i2c_bus(3, 400, NULL, 0);
> return 0;
> }
> Index: linux-beagle/drivers/i2c/busses/Kconfig
> ===================================================================
> --- linux-beagle.orig/drivers/i2c/busses/Kconfig
> +++ linux-beagle/drivers/i2c/busses/Kconfig
> @@ -332,10 +332,27 @@ config I2C_OMAP
> default y if MACH_OMAP_H3 || MACH_OMAP_OSK
> help
> If you say yes to this option, support will be included for the
> - I2C interface on the Texas Instruments OMAP1/2 family of processors.
> - Like OMAP1510/1610/1710/5912 and OMAP242x.
> + I2C interface on the Texas Instruments OMAP1/2/3 family of
> + processors.
> + Like OMAP1510/1610/1710/5912, OMAP242x, OMAP34x and OMAP35x.
> For details see http://www.ti.com/omap.
>
> +config I2C2_OMAP_BEAGLE
> + bool "Enable I2C2 for OMAP3 BeagleBoard"
> + depends on ARCH_OMAP && MACH_OMAP3_BEAGLE
> + select OMAP_MUX
> + default n
> + help
> + Say Y here if you want to enable I2C bus 2 at OMAP3 based
> + BeagleBoard.
> + I2C2 at BeagleBoard is connected to expansion connector, i.e. unused
> + if nothing is connected to this connector. As internal OMAP3 pull up
> + resistors are not strong enough, enabled but unused I2C2 bus results
> + in error messages (e.g. I2C timeouts). Enable this only if you have
> + something connected to I2C2 at board's expansion connector and this
> + extension has additional pull up resistors for I2C2 bus.
> +
> +
> config I2C_PARPORT
> tristate "Parallel port adapter"
> depends on PARPORT
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
