I2C2 at BeagleBoard is connected to expansion connector, i.e. unused
if nothing is connected to this connector. As internal OMAP3 pull up
resistors are not strong enough, enabled but unused I2C2 bus results
in error messages (e.g. I2C timeouts). I2C2 should be enabled only if
something is connected to I2C2 at board's expansion connector and this
extension has additional pull up resistors for I2C2 bus.
- Add configuration option for this
- Use configuration option in board-omap3beagle
- While being there, add OMAP3 to OMAP I2C help text
Signed-off-by: Dirk Behme <dirk.behme@xxxxxxxxx>
Subject: ARM: OMAP3: Make I2C bus 2 configurable for BeagleBoard
From: Dirk Behme <dirk.behme@xxxxxxxxx>
I2C2 at BeagleBoard is connected to expansion connector, i.e. unused if
nothing is connected to this connector. As internal OMAP3 pull up resistors
are not strong enough, enabled but unused I2C2 bus results in error messages
(e.g. I2C timeouts). I2C2 should be enabled only if something is connected to
I2C2 at board's expansion connector and this extension has additional pull up
resistors for I2C2 bus.
- Add configuration option for this
- Use configuration option in board-omap3beagle
- While being there, add OMAP3 to OMAP I2C help text
Signed-off-by: Dirk Behme <dirk.behme@xxxxxxxxx>
---
Changes in v2: Incorporate Jarkko's comments. Pin mux is already done
depending on enabled busses in omap_i2c_mux_pins(int bus).
We don't have to do it manually here. Thanks!
Index: linux-beagle/arch/arm/mach-omap2/board-omap3beagle.c
===================================================================
--- linux-beagle.orig/arch/arm/mach-omap2/board-omap3beagle.c
+++ linux-beagle/arch/arm/mach-omap2/board-omap3beagle.c
@@ -40,7 +40,9 @@ static struct omap_uart_config omap3_bea
static int __init omap3_beagle_i2c_init(void)
{
omap_register_i2c_bus(1, 2600, NULL, 0);
+#ifdef CONFIG_I2C2_OMAP_BEAGLE
omap_register_i2c_bus(2, 400, NULL, 0);
+#endif
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
Index: linux-beagle/drivers/i2c/busses/Kconfig
===================================================================
--- linux-beagle.orig/drivers/i2c/busses/Kconfig
+++ linux-beagle/drivers/i2c/busses/Kconfig
@@ -332,10 +332,27 @@ config I2C_OMAP
default y if MACH_OMAP_H3 || MACH_OMAP_OSK
help
If you say yes to this option, support will be included for the
- I2C interface on the Texas Instruments OMAP1/2 family of processors.
- Like OMAP1510/1610/1710/5912 and OMAP242x.
+ I2C interface on the Texas Instruments OMAP1/2/3 family of
+ processors.
+ Like OMAP1510/1610/1710/5912, OMAP242x, OMAP34x and OMAP35x.
For details see http://www.ti.com/omap.
+config I2C2_OMAP_BEAGLE
+ bool "Enable I2C2 for OMAP3 BeagleBoard"
+ depends on ARCH_OMAP && MACH_OMAP3_BEAGLE
+ select OMAP_MUX
+ default n
+ help
+ Say Y here if you want to enable I2C bus 2 at OMAP3 based
+ BeagleBoard.
+ I2C2 at BeagleBoard is connected to expansion connector, i.e. unused
+ if nothing is connected to this connector. As internal OMAP3 pull up
+ resistors are not strong enough, enabled but unused I2C2 bus results
+ in error messages (e.g. I2C timeouts). Enable this only if you have
+ something connected to I2C2 at board's expansion connector and this
+ extension has additional pull up resistors for I2C2 bus.
+
+
config I2C_PARPORT
tristate "Parallel port adapter"
depends on PARPORT
