This workaround enables autoidle for interface clocks and plls. Also
automatic control of external oscillator through sys_clkreq is
enabled.
Proper fix to this is to generalize omap3_dpll_allow_idle,
omap3_dpll_deny_idle, omap3_dpll_autoidle_read and call it for each
clock on init.
Signed-off-by: Jouni Hogander <jouni.hogander@xxxxxxxxx>
---
arch/arm/mach-omap2/pm34xx.c | 120 ++++++++++++++++++++++++++++++++++++++++++
1 files changed, 120 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index e1799a5..2008665 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -433,6 +433,126 @@ static void __init prcm_setup_regs(void)
} else
prm_write_mod_reg(0, GFX_MOD, PM_WKDEP);
+ /* XXX Enable interface clock autoidle for all modules. This
+ * should be done by clockfw */
+ cm_write_mod_reg(
+ OMAP3430ES2_AUTO_MMC3 |
+ OMAP3430ES2_AUTO_ICR |
+ OMAP3430_AUTO_AES2 |
+ OMAP3430_AUTO_SHA12 |
+ OMAP3430_AUTO_DES2 |
+ OMAP3430_AUTO_MMC2 |
+ OMAP3430_AUTO_MMC1 |
+ OMAP3430_AUTO_MSPRO |
+ OMAP3430_AUTO_HDQ |
+ OMAP3430_AUTO_MCSPI4 |
+ OMAP3430_AUTO_MCSPI3 |
+ OMAP3430_AUTO_MCSPI2 |
+ OMAP3430_AUTO_MCSPI1 |
+ OMAP3430_AUTO_I2C3 |
+ OMAP3430_AUTO_I2C2 |
+ OMAP3430_AUTO_I2C1 |
+ OMAP3430_AUTO_UART2 |
+ OMAP3430_AUTO_UART1 |
+ OMAP3430_AUTO_GPT11 |
+ OMAP3430_AUTO_GPT10 |
+ OMAP3430_AUTO_MCBSP5 |
+ OMAP3430_AUTO_MCBSP1 |
+ OMAP3430ES1_AUTO_FAC | /* This is es1 only */
+ OMAP3430_AUTO_MAILBOXES |
+ OMAP3430_AUTO_OMAPCTRL |
+ OMAP3430ES1_AUTO_FSHOSTUSB |
+ OMAP3430_AUTO_HSOTGUSB |
+ OMAP3430ES1_AUTO_D2D | /* This is es1 only */
+ OMAP3430_AUTO_SSI,
+ CORE_MOD, CM_AUTOIDLE1);
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_PKA |
+ OMAP3430_AUTO_AES1 |
+ OMAP3430_AUTO_RNG |
+ OMAP3430_AUTO_SHA11 |
+ OMAP3430_AUTO_DES1,
+ CORE_MOD, CM_AUTOIDLE2);
+
+ if (is_sil_rev_greater_than(OMAP3430_REV_ES1_0)) {
+ cm_write_mod_reg(
+ OMAP3430ES2_AUTO_USBTLL,
+ CORE_MOD, CM_AUTOIDLE3);
+ }
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_WDT2 |
+ OMAP3430_AUTO_WDT1 |
+ OMAP3430_AUTO_GPIO1 |
+ OMAP3430_AUTO_32KSYNC |
+ OMAP3430_AUTO_GPT12 |
+ OMAP3430_AUTO_GPT1 ,
+ WKUP_MOD, CM_AUTOIDLE);
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_DSS,
+ OMAP3430_DSS_MOD,
+ CM_AUTOIDLE);
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_CAM,
+ OMAP3430_CAM_MOD,
+ CM_AUTOIDLE);
+
+ cm_write_mod_reg(
+ OMAP3430_AUTO_GPIO6 |
+ OMAP3430_AUTO_GPIO5 |
+ OMAP3430_AUTO_GPIO4 |
+ OMAP3430_AUTO_GPIO3 |
+ OMAP3430_AUTO_GPIO2 |
+ OMAP3430_AUTO_WDT3 |
+ OMAP3430_AUTO_UART3 |
+ OMAP3430_AUTO_GPT9 |
+ OMAP3430_AUTO_GPT8 |
+ OMAP3430_AUTO_GPT7 |
+ OMAP3430_AUTO_GPT6 |
+ OMAP3430_AUTO_GPT5 |
+ OMAP3430_AUTO_GPT4 |
+ OMAP3430_AUTO_GPT3 |
+ OMAP3430_AUTO_GPT2 |
+ OMAP3430_AUTO_MCBSP4 |
+ OMAP3430_AUTO_MCBSP3 |
+ OMAP3430_AUTO_MCBSP2,
+ OMAP3430_PER_MOD,
+ CM_AUTOIDLE);
+
+ if (is_sil_rev_greater_than(OMAP3430_REV_ES1_0)) {
+ cm_write_mod_reg(
+ OMAP3430ES2_AUTO_USBHOST,
+ OMAP3430ES2_USBHOST_MOD,
+ CM_AUTOIDLE);
+ }
+
+ /* XXX Set all plls to autoidle. This is needed until autoidle is
+ * enabled by clockfw */
+ cm_write_mod_reg(1 << OMAP3430_CLKTRCTRL_IVA2_SHIFT,
+ OMAP3430_IVA2_MOD,
+ CM_AUTOIDLE2);
+ cm_write_mod_reg(1 << OMAP3430_AUTO_MPU_DPLL_SHIFT,
+ MPU_MOD,
+ CM_AUTOIDLE2);
+ cm_write_mod_reg((1 << OMAP3430_AUTO_PERIPH_DPLL_SHIFT) |
+ (1 << OMAP3430_AUTO_CORE_DPLL_SHIFT),
+ PLL_MOD,
+ CM_AUTOIDLE);
+ cm_write_mod_reg(1 << OMAP3430ES2_AUTO_PERIPH2_DPLL_SHIFT,
+ PLL_MOD,
+ CM_AUTOIDLE2);
+
+ /* XXX Enable control of expternal oscillator through
+ * sys_clkreq. I think clockfw should provide means to do this
+ */
+ prm_rmw_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK,
+ 1 << OMAP_AUTOEXTCLKMODE_SHIFT,
+ OMAP3430_GR_MOD,
+ OMAP3_PRM_CLKSRC_CTRL_OFFSET);
+
/* setup wakup source */
prm_write_mod_reg(OMAP3430_EN_IO | OMAP3430_EN_GPIO1 | OMAP3430_EN_GPT1,
WKUP_MOD, PM_WKEN);
--
1.5.5
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
