Split sleep24xx.S into sleep242x.S and sleep243x.S. This is easier
to follow than rewriting the registers.
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
---
arch/arm/mach-omap2/Makefile | 13 ++--
arch/arm/mach-omap2/pm24xx.c | 30 ++++-----
arch/arm/mach-omap2/sleep242x.S | 131 ++++++++++++++++++++++++++++++++++++++
arch/arm/mach-omap2/sleep243x.S | 131 ++++++++++++++++++++++++++++++++++++++
arch/arm/mach-omap2/sleep24xx.S | 133 ---------------------------------------
include/asm-arm/arch-omap/pm.h | 12 +++-
6 files changed, 289 insertions(+), 161 deletions(-)
create mode 100644 arch/arm/mach-omap2/sleep242x.S
create mode 100644 arch/arm/mach-omap2/sleep243x.S
delete mode 100644 arch/arm/mach-omap2/sleep24xx.S
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index b617b66..db82eb1 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -14,15 +14,14 @@ obj-$(CONFIG_ARCH_OMAP3) += sram34xx.o
# Power Management
obj-$(CONFIG_PM) += pm.o
-ifeq ($(CONFIG_ARCH_OMAP2),y)
-obj-$(CONFIG_PM) += pm24xx.o sleep24xx.o
+ifeq ($(CONFIG_PM),y)
+obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o
+obj-$(CONFIG_ARCH_OMAP2420) += sleep242x.o
+obj-$(CONFIG_ARCH_OMAP2430) += sleep243x.o
+obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o
+obj-$(CONFIG_PM_DEBUG) += pm-debug.o
endif
-ifeq ($(CONFIG_ARCH_OMAP3),y)
-obj-$(CONFIG_PM) += pm34xx.o sleep34xx.o
-endif
-obj-$(CONFIG_PM_DEBUG) += pm-debug.o
-
# Clock framework
obj-$(CONFIG_ARCH_OMAP2) += clock24xx.o
obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index 787a95e..aab079e 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -52,10 +52,6 @@
#include "sdrc.h"
#include "pm.h"
-/* These addrs are in assembly language code to be patched at runtime */
-extern void *omap2_ocs_sdrc_power;
-extern void *omap2_ocs_sdrc_dlla_ctrl;
-
static void (*omap2_sram_idle)(void);
static void (*omap2_sram_suspend)(void __iomem *dllctrl);
static void (*saved_idle)(void);
@@ -495,19 +491,19 @@ int __init omap2_pm_init(void)
* These routines need to be in SRAM as that's the only
* memory the MPU can see when it wakes up.
*/
- omap2_sram_idle = omap_sram_push(omap24xx_idle_loop_suspend,
- omap24xx_idle_loop_suspend_sz);
-
- omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
- omap24xx_cpu_suspend_sz);
-
- /* Patch in the correct register addresses for multiboot */
- omap_sram_patch_va(omap24xx_cpu_suspend, &omap2_ocs_sdrc_power,
- omap2_sram_suspend,
- OMAP_SDRC_REGADDR(SDRC_POWER));
- omap_sram_patch_va(omap24xx_cpu_suspend, &omap2_ocs_sdrc_dlla_ctrl,
- omap2_sram_suspend,
- OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL));
+ if (cpu_is_omap242x()) {
+ omap2_sram_idle = omap_sram_push(omap242x_idle_loop_suspend,
+ omap242x_idle_loop_suspend_sz);
+
+ omap2_sram_suspend = omap_sram_push(omap242x_cpu_suspend,
+ omap242x_cpu_suspend_sz);
+ } else {
+ omap2_sram_idle = omap_sram_push(omap243x_idle_loop_suspend,
+ omap243x_idle_loop_suspend_sz);
+
+ omap2_sram_suspend = omap_sram_push(omap243x_cpu_suspend,
+ omap243x_cpu_suspend_sz);
+ }
suspend_set_ops(&omap_pm_ops);
pm_idle = omap2_pm_idle;
diff --git a/arch/arm/mach-omap2/sleep242x.S b/arch/arm/mach-omap2/sleep242x.S
new file mode 100644
index 0000000..33bdd01
--- /dev/null
+++ b/arch/arm/mach-omap2/sleep242x.S
@@ -0,0 +1,131 @@
+/*
+ * linux/arch/arm/mach-omap2/sleep.S
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@xxxxxx>
+ *
+ * (C) Copyright 2006 Nokia Corporation
+ * Fixed idle loop sleep
+ * Igor Stoppa <igor.stoppa@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/arch/io.h>
+#include <asm/arch/pm.h>
+
+#include <asm/arch/omap24xx.h>
+
+#include "sdrc.h"
+
+/* First address of reserved address space? apparently valid for OMAP2 & 3 */
+#define A_SDRC0_V (0xC0000000)
+
+ .text
+
+/*
+ * Forces OMAP into idle state
+ *
+ * omap242x_idle_loop_suspend() - This bit of code just executes the WFI
+ * for normal idles.
+ *
+ * Note: This code get's copied to internal SRAM at boot. When the OMAP
+ * wakes up it continues execution at the point it went to sleep.
+ */
+ENTRY(omap242x_idle_loop_suspend)
+ stmfd sp!, {r0, lr} @ save registers on stack
+ mov r0, #0x0 @ clear for mrc call
+ mcr p15, 0, r0, c7, c0, 4 @ wait for interrupt
+ ldmfd sp!, {r0, pc} @ restore regs and return
+
+ENTRY(omap242x_idle_loop_suspend_sz)
+ .word . - omap242x_idle_loop_suspend
+
+/*
+ * omap242x_cpu_suspend() - Forces OMAP into deep sleep state by completing
+ * SDRC shutdown then ARM shutdown. Upon wake MPU is back on so just restore
+ * SDRC.
+ *
+ * Input:
+ * R0 : DLL ctrl value pre-Sleep
+ *
+ * The if the DPLL is going to AutoIdle. It seems like the DPLL may be back on
+ * when we get called, but the DLL probably isn't. We will wait a bit more in
+ * case the DPLL isn't quite there yet. The code will wait on DLL for DDR even
+ * if in unlocked mode.
+ *
+ * For less than 242x-ES2.2 upon wake from a sleep mode where the external
+ * oscillator was stopped, a timing bug exists where a non-stabilized 12MHz
+ * clock can pass into the PRCM can cause problems at DSP and IVA.
+ * To work around this the code will switch to the 32kHz source prior to sleep.
+ * Post sleep we will shift back to using the DPLL. Apparently,
+ * CM_IDLEST_CLKGEN does not reflect the full clock change so you need to wait
+ * 3x12MHz + 3x32kHz clocks for a full switch.
+ *
+ * The DLL load value is not kept in RETENTION or OFF. It needs to be restored
+ * at wake
+ */
+ENTRY(omap242x_cpu_suspend)
+ stmfd sp!, {r0 - r12, lr} @ save registers on stack
+ mov r3, #0x0 @ clear for mrc call
+ mcr p15, 0, r3, c7, c10, 4 @ memory barrier, hope SDR/DDR finished
+ nop
+ nop
+ ldr r3, omap2_ocs_sdrc_power @ addr of sdrc power
+ ldr r4, [r3] @ value of sdrc power
+ orr r4, r4, #0x40 @ enable self refresh on idle req
+ mov r5, #0x2000 @ set delay (DPLL relock + DLL relock)
+ str r4, [r3] @ make it so
+ mov r2, #0
+ nop
+ mcr p15, 0, r2, c7, c0, 4 @ wait for interrupt
+ nop
+loop:
+ subs r5, r5, #0x1 @ awake, wait just a bit
+ bne loop
+
+ /* The DPLL has on before we take the DDR out of self refresh */
+ bic r4, r4, #0x40 @ now clear self refresh bit.
+ str r4, [r3] @ put vlaue back.
+ ldr r4, A_SDRC0 @ make a clock happen
+ ldr r4, [r4]
+ nop @ start auto refresh only after clk ok
+ movs r0, r0 @ see if DDR or SDR
+ ldrne r1, omap2_ocs_sdrc_dlla_ctrl @ get addr of DLL ctrl
+ strne r0, [r1] @ rewrite DLLA to force DLL reload
+ addne r1, r1, #0x8 @ move to DLLB
+ strne r0, [r1] @ rewrite DLLB to force DLL reload
+
+ mov r5, #0x1000
+loop2:
+ subs r5, r5, #0x1
+ bne loop2
+ /* resume*/
+ ldmfd sp!, {r0 - r12, pc} @ restore regs and return
+
+omap2_ocs_sdrc_power:
+ .word OMAP242X_SDRC_REGADDR(SDRC_POWER)
+A_SDRC0:
+ .word A_SDRC0_V
+omap2_ocs_sdrc_dlla_ctrl:
+ .word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
+
+ENTRY(omap242x_cpu_suspend_sz)
+ .word . - omap242x_cpu_suspend
+
diff --git a/arch/arm/mach-omap2/sleep243x.S b/arch/arm/mach-omap2/sleep243x.S
new file mode 100644
index 0000000..9a2b4b7
--- /dev/null
+++ b/arch/arm/mach-omap2/sleep243x.S
@@ -0,0 +1,131 @@
+/*
+ * linux/arch/arm/mach-omap2/sleep.S
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@xxxxxx>
+ *
+ * (C) Copyright 2006 Nokia Corporation
+ * Fixed idle loop sleep
+ * Igor Stoppa <igor.stoppa@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/arch/io.h>
+#include <asm/arch/pm.h>
+
+#include <asm/arch/omap24xx.h>
+
+#include "sdrc.h"
+
+/* First address of reserved address space? apparently valid for OMAP2 & 3 */
+#define A_SDRC0_V (0xC0000000)
+
+ .text
+
+/*
+ * Forces OMAP into idle state
+ *
+ * omap243x_idle_loop_suspend() - This bit of code just executes the WFI
+ * for normal idles.
+ *
+ * Note: This code get's copied to internal SRAM at boot. When the OMAP
+ * wakes up it continues execution at the point it went to sleep.
+ */
+ENTRY(omap243x_idle_loop_suspend)
+ stmfd sp!, {r0, lr} @ save registers on stack
+ mov r0, #0x0 @ clear for mrc call
+ mcr p15, 0, r0, c7, c0, 4 @ wait for interrupt
+ ldmfd sp!, {r0, pc} @ restore regs and return
+
+ENTRY(omap243x_idle_loop_suspend_sz)
+ .word . - omap243x_idle_loop_suspend
+
+/*
+ * omap243x_cpu_suspend() - Forces OMAP into deep sleep state by completing
+ * SDRC shutdown then ARM shutdown. Upon wake MPU is back on so just restore
+ * SDRC.
+ *
+ * Input:
+ * R0 : DLL ctrl value pre-Sleep
+ *
+ * The if the DPLL is going to AutoIdle. It seems like the DPLL may be back on
+ * when we get called, but the DLL probably isn't. We will wait a bit more in
+ * case the DPLL isn't quite there yet. The code will wait on DLL for DDR even
+ * if in unlocked mode.
+ *
+ * For less than 242x-ES2.2 upon wake from a sleep mode where the external
+ * oscillator was stopped, a timing bug exists where a non-stabilized 12MHz
+ * clock can pass into the PRCM can cause problems at DSP and IVA.
+ * To work around this the code will switch to the 32kHz source prior to sleep.
+ * Post sleep we will shift back to using the DPLL. Apparently,
+ * CM_IDLEST_CLKGEN does not reflect the full clock change so you need to wait
+ * 3x12MHz + 3x32kHz clocks for a full switch.
+ *
+ * The DLL load value is not kept in RETENTION or OFF. It needs to be restored
+ * at wake
+ */
+ENTRY(omap243x_cpu_suspend)
+ stmfd sp!, {r0 - r12, lr} @ save registers on stack
+ mov r3, #0x0 @ clear for mrc call
+ mcr p15, 0, r3, c7, c10, 4 @ memory barrier, hope SDR/DDR finished
+ nop
+ nop
+ ldr r3, omap2_ocs_sdrc_power @ addr of sdrc power
+ ldr r4, [r3] @ value of sdrc power
+ orr r4, r4, #0x40 @ enable self refresh on idle req
+ mov r5, #0x2000 @ set delay (DPLL relock + DLL relock)
+ str r4, [r3] @ make it so
+ mov r2, #0
+ nop
+ mcr p15, 0, r2, c7, c0, 4 @ wait for interrupt
+ nop
+loop:
+ subs r5, r5, #0x1 @ awake, wait just a bit
+ bne loop
+
+ /* The DPLL has on before we take the DDR out of self refresh */
+ bic r4, r4, #0x40 @ now clear self refresh bit.
+ str r4, [r3] @ put vlaue back.
+ ldr r4, A_SDRC0 @ make a clock happen
+ ldr r4, [r4]
+ nop @ start auto refresh only after clk ok
+ movs r0, r0 @ see if DDR or SDR
+ ldrne r1, omap2_ocs_sdrc_dlla_ctrl @ get addr of DLL ctrl
+ strne r0, [r1] @ rewrite DLLA to force DLL reload
+ addne r1, r1, #0x8 @ move to DLLB
+ strne r0, [r1] @ rewrite DLLB to force DLL reload
+
+ mov r5, #0x1000
+loop2:
+ subs r5, r5, #0x1
+ bne loop2
+ /* resume*/
+ ldmfd sp!, {r0 - r12, pc} @ restore regs and return
+
+omap2_ocs_sdrc_power:
+ .word OMAP243X_SDRC_REGADDR(SDRC_POWER)
+A_SDRC0:
+ .word A_SDRC0_V
+omap2_ocs_sdrc_dlla_ctrl:
+ .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
+
+ENTRY(omap243x_cpu_suspend_sz)
+ .word . - omap243x_cpu_suspend
+
diff --git a/arch/arm/mach-omap2/sleep24xx.S b/arch/arm/mach-omap2/sleep24xx.S
deleted file mode 100644
index 3e0a7dc..0000000
--- a/arch/arm/mach-omap2/sleep24xx.S
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/sleep.S
- *
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Richard Woodruff <r-woodruff2@xxxxxx>
- *
- * (C) Copyright 2006 Nokia Corporation
- * Fixed idle loop sleep
- * Igor Stoppa <igor.stoppa@xxxxxxxxx>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <linux/linkage.h>
-#include <linux/poison.h> /* for SRAM_VA_MAGIC */
-#include <asm/assembler.h>
-#include <asm/arch/io.h>
-#include <asm/arch/pm.h>
-
-#include <asm/arch/omap24xx.h>
-
-/* First address of reserved address space? apparently valid for OMAP2 & 3 */
-#define A_SDRC0_V (0xC0000000)
-
- .text
-
-/*
- * Forces OMAP into idle state
- *
- * omap24xx_idle_loop_suspend() - This bit of code just executes the WFI
- * for normal idles.
- *
- * Note: This code get's copied to internal SRAM at boot. When the OMAP
- * wakes up it continues execution at the point it went to sleep.
- */
-ENTRY(omap24xx_idle_loop_suspend)
- stmfd sp!, {r0, lr} @ save registers on stack
- mov r0, #0x0 @ clear for mrc call
- mcr p15, 0, r0, c7, c0, 4 @ wait for interrupt
- ldmfd sp!, {r0, pc} @ restore regs and return
-
-ENTRY(omap24xx_idle_loop_suspend_sz)
- .word . - omap24xx_idle_loop_suspend
-
-/*
- * omap242x_cpu_suspend() - Forces OMAP into deep sleep state by completing
- * SDRC shutdown then ARM shutdown. Upon wake MPU is back on so just restore
- * SDRC.
- *
- * Input:
- * R0 : DLL ctrl value pre-Sleep
- *
- * The if the DPLL is going to AutoIdle. It seems like the DPLL may be back on
- * when we get called, but the DLL probably isn't. We will wait a bit more in
- * case the DPLL isn't quite there yet. The code will wait on DLL for DDR even
- * if in unlocked mode.
- *
- * For less than 242x-ES2.2 upon wake from a sleep mode where the external
- * oscillator was stopped, a timing bug exists where a non-stabilized 12MHz
- * clock can pass into the PRCM can cause problems at DSP and IVA.
- * To work around this the code will switch to the 32kHz source prior to sleep.
- * Post sleep we will shift back to using the DPLL. Apparently,
- * CM_IDLEST_CLKGEN does not reflect the full clock change so you need to wait
- * 3x12MHz + 3x32kHz clocks for a full switch.
- *
- * The DLL load value is not kept in RETENTION or OFF. It needs to be restored
- * at wake
- */
-ENTRY(omap24xx_cpu_suspend)
- stmfd sp!, {r0 - r12, lr} @ save registers on stack
- mov r3, #0x0 @ clear for mrc call
- mcr p15, 0, r3, c7, c10, 4 @ memory barrier, hope SDR/DDR finished
- nop
- nop
- ldr r3, omap2_ocs_sdrc_power @ addr of sdrc power
- ldr r4, [r3] @ value of sdrc power
- orr r4, r4, #0x40 @ enable self refresh on idle req
- mov r5, #0x2000 @ set delay (DPLL relock + DLL relock)
- str r4, [r3] @ make it so
- mov r2, #0
- nop
- mcr p15, 0, r2, c7, c0, 4 @ wait for interrupt
- nop
-loop:
- subs r5, r5, #0x1 @ awake, wait just a bit
- bne loop
-
- /* The DPLL has on before we take the DDR out of self refresh */
- bic r4, r4, #0x40 @ now clear self refresh bit.
- str r4, [r3] @ put vlaue back.
- ldr r4, A_SDRC0 @ make a clock happen
- ldr r4, [r4]
- nop @ start auto refresh only after clk ok
- movs r0, r0 @ see if DDR or SDR
- ldrne r1, omap2_ocs_sdrc_dlla_ctrl @ get addr of DLL ctrl
- strne r0, [r1] @ rewrite DLLA to force DLL reload
- addne r1, r1, #0x8 @ move to DLLB
- strne r0, [r1] @ rewrite DLLB to force DLL reload
-
- mov r5, #0x1000
-loop2:
- subs r5, r5, #0x1
- bne loop2
- /* resume*/
- ldmfd sp!, {r0 - r12, pc} @ restore regs and return
-
- .globl omap2_ocs_sdrc_power
- .globl omap2_ocs_sdrc_dlla_ctrl
-
-omap2_ocs_sdrc_power:
- .word SRAM_VA_MAGIC
-A_SDRC0:
- .word A_SDRC0_V
-omap2_ocs_sdrc_dlla_ctrl:
- .word SRAM_VA_MAGIC
-
-ENTRY(omap24xx_cpu_suspend_sz)
- .word . - omap24xx_cpu_suspend
-
diff --git a/include/asm-arm/arch-omap/pm.h b/include/asm-arm/arch-omap/pm.h
index d0c7d4d..bafe109 100644
--- a/include/asm-arm/arch-omap/pm.h
+++ b/include/asm-arm/arch-omap/pm.h
@@ -145,22 +145,26 @@ static inline void omap2_allow_sleep(void) { }
extern void omap730_cpu_suspend(unsigned short, unsigned short);
extern void omap1510_cpu_suspend(unsigned short, unsigned short);
extern void omap1610_cpu_suspend(unsigned short, unsigned short);
-extern void omap24xx_cpu_suspend(u32 dll_ctrl, u32 cpu_revision);
+extern void omap242x_cpu_suspend(u32 dll_ctrl, u32 cpu_revision);
+extern void omap243x_cpu_suspend(u32 dll_ctrl, u32 cpu_revision);
extern void omap34xx_cpu_suspend(u32 *addr, int save_state);
extern void omap730_idle_loop_suspend(void);
extern void omap1510_idle_loop_suspend(void);
extern void omap1610_idle_loop_suspend(void);
-extern void omap24xx_idle_loop_suspend(void);
+extern void omap242x_idle_loop_suspend(void);
+extern void omap243x_idle_loop_suspend(void);
extern unsigned int omap730_cpu_suspend_sz;
extern unsigned int omap1510_cpu_suspend_sz;
extern unsigned int omap1610_cpu_suspend_sz;
-extern unsigned int omap24xx_cpu_suspend_sz;
+extern unsigned int omap242x_cpu_suspend_sz;
+extern unsigned int omap243x_cpu_suspend_sz;
extern unsigned int omap34xx_cpu_suspend_sz;
extern unsigned int omap730_idle_loop_suspend_sz;
extern unsigned int omap1510_idle_loop_suspend_sz;
extern unsigned int omap1610_idle_loop_suspend_sz;
-extern unsigned int omap24xx_idle_loop_suspend_sz;
+extern unsigned int omap242x_idle_loop_suspend_sz;
+extern unsigned int omap243x_idle_loop_suspend_sz;
extern unsigned int omap34xx_suspend_sz;
#ifdef CONFIG_OMAP_SERIAL_WAKE
--
1.5.3.6
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
