Re: 2430SDP booting problem with the latest git

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1


Op 9 mei 2008, om 15:42 heeft Felipe Balbi het volgende geschreven:


On Fri, 9 May 2008 18:43:40 +0530, "arun c"

<snip>

TWL4030 GPIO Demux: IRQ Range 384 to 402, Initialization Failed
omapflash.0: Found 1 x16 devices at 0x0 in 16-bit bank
omapflash.0: Found 1 x16 devices at 0x2000000 in 16-bit bank
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
OMAP2 OneNAND driver initializing
input: omap_twl4030keypad as /class/input/input0
omap_twl4030keypad omap_twl4030keypad: Could not write TWL4030: 0 -
ret -121[ff]OMAP Watchdog Timer Rev 0x22: initial timeout 60 sec
mmci-omap: probe of mmci-omap.1 failed with error -22

Besides the omapfb, this took my attention as well.
MMC is failing on 2430sdp, could anyone take a look at it ?

Lots of TWL related stuff is failing (from log above):

TWL4030 GPIO Demux: IRQ Range 384 to 402, Initialization Failed

omap_twl4030keypad omap_twl4030keypad: Could not write TWL4030: 0 -

So the mmc problem might be the twl acting up: http://thread.gmane.org/gmane.linux.ports.arm.omap/8173

regards,

Koen






TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Power Management for OMAP2 initializing
PRCM revision 1.0
eth0: link up
Sending DHCP requests ., OK
IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.13.153
IP-Config: Complete:
    device=eth0, addr=192.168.13.153, mask=255.255.255.0,
gw=192.168.13.188,
    host=192.168.13.153, domain=, nis-domain=(none),
    bootserver=0.0.0.0, rootserver=192.168.10.135, rootpath=
Looking up port of RPC 100003/2 on 192.168.10.135
###########################################

Regards,
Arun C

-- Best Regards,

Felipe Balbi
http://felipebalbi.com
me@xxxxxxxxxxxxxxx

--
To unsubscribe from this list: send the line "unsubscribe linux- omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (Darwin)

iD8DBQFIJGO7MkyGM64RGpERArnUAJ9IZCnp3dMFr8c8glPATMs0ZnCPpQCgrkys
XMdm6x3WbJYwJsEHq99iwa4=
=3M2b
-----END PGP SIGNATURE-----
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux