Hi all,
While booting the 2430sdp with the latest git kernel nothing is
coming on lcd, omapfb driver fails to initialize the lcd due
to twl4030 accessing errors.
I have tested the hardware with the 2.6.14 kernel from ti
site, its working fine.
boot log is pasted below below(also attached).
##################################################################
Uncompressing Linux.............................................................Linux
version 2.6.26-rc1-omap1-04724-gcb170dc (arunc@atlas) (gcc version
4.2.0 8CPU: ARMv6-compatible processor [4107b365] revision 5
(ARMv6TEJ), cr=00c5387f
Machine: OMAP2430 sdp2430 board
Memory policy: ECC disabled, Data cache writeback
OMAP2430<6>ES0<6>
SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000
CPU0: D VIPT write-back cache
CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: mem=64M console=ttyS0,115200n8 noinitrd
root=/dev/nfs rw npClocking rate (Crystal/DPLL/MPU): 13.0/532/266 MHz
clock.c: Enable for gpmc_fck without enable code
GPMC revision 3.0
IRQ: Found an INTC at 0xd80fe000 (revision 3.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP243x GPIO hardware version 2.4
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61580KB available (2872K code, 285K data, 124K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 192 bytes
NET: Registered protocol family 16
NAND: Found NAND on CS 0
OMAP DMA hardware revision 4.0
Initializing OMAP McBSP system
omap_dsp_init() done
USB: No board-specific platform config found
i2c_omap i2c_omap.1: bus 1 rev3.7 at 400 kHz
i2c_omap i2c_omap.2: bus 2 rev3.7 at 2600 kHz
TWL4030: TRY attach Slave TWL4030-ID0 on Adapter OMAP I2C adapter [1]
TWL4030: TRY attach Slave TWL4030-ID1 on Adapter OMAP I2C adapter [1]
TWL4030: TRY attach Slave TWL4030-ID2 on Adapter OMAP I2C adapter [1]
TWL4030: TRY attach Slave TWL4030-ID3 on Adapter OMAP I2C adapter [1]
Unable to register interrupt subsystem[-121][728]
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) .. 2001-2006 Red Hat, Inc.
msgmni has been set to 120 for ipc namespace c030c208
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
omapfb: configured for panel sdp2430
omapfb: DISPC version 3.0 initialized
omap_rng omap_rng: OMAP Random Number Generator ver. 50
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.0: ttyS2 at MMIO 0x4806e000 (irq = 74) is a ST16654
brd: module loaded
loop: module loaded
smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <nico@xxxxxxx>
eth0: SMC91C94 (rev 9) at c4850300 IRQ 309 [nowait]
eth0: Ethernet addr: 00:80:10:01:02:03
i2c /dev entries driver
TWL4030 GPIO Demux: IRQ Range 384 to 402, Initialization Failed
omapflash.0: Found 1 x16 devices at 0x0 in 16-bit bank
omapflash.0: Found 1 x16 devices at 0x2000000 in 16-bit bank
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
OMAP2 OneNAND driver initializing
input: omap_twl4030keypad as /class/input/input0
omap_twl4030keypad omap_twl4030keypad: Could not write TWL4030: 0 -
ret -121[ff]OMAP Watchdog Timer Rev 0x22: initial timeout 60 sec
mmci-omap: probe of mmci-omap.1 failed with error -22
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Power Management for OMAP2 initializing
PRCM revision 1.0
eth0: link up
Sending DHCP requests ., OK
IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.13.153
IP-Config: Complete:
device=eth0, addr=192.168.13.153, mask=255.255.255.0, gw=192.168.13.188,
host=192.168.13.153, domain=, nis-domain=(none),
bootserver=0.0.0.0, rootserver=192.168.10.135, rootpath=
Looking up port of RPC 100003/2 on 192.168.10.135
###########################################
Regards,
Arun C
Attachment:
bootlog
Description: Binary data
