Use the newer touchscreen driver (tsc210x).
The old one doesn't compile anymore.
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@xxxxxxxxxxx>
---
arch/arm/mach-omap1/board-h3.c | 86 ++++++----------------------------------
1 files changed, 13 insertions(+), 73 deletions(-)
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index df77cf5..a12fa17 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -27,7 +27,7 @@
#include <linux/input.h>
#include <linux/clk.h>
#include <linux/spi/spi.h>
-#include <linux/spi/tsc2101.h>
+#include <linux/spi/tsc210x.h>
#include <asm/setup.h>
#include <asm/page.h>
@@ -374,77 +374,10 @@ static struct platform_device h3_lcd_device = {
.id = -1,
};
-struct {
- struct clk *mclk;
- int initialized;
-} h3_tsc2101;
-
-#define TSC2101_MUX_MCLK_ON V5_1710_MCLK_ON
-#define TSC2101_MUX_MCLK_OFF V5_1710_MCLK_OFF
-
-static int h3_tsc2101_init(struct spi_device *spi)
-{
- u8 io_exp_val;
- int r;
-
- if (h3_tsc2101.initialized) {
- printk(KERN_ERR "tsc2101: already initialized\n");
- return -ENODEV;
- }
-
- /* Get the MCLK */
- h3_tsc2101.mclk = clk_get(&spi->dev, "mclk");
- if (IS_ERR(h3_tsc2101.mclk)) {
- dev_err(&spi->dev, "unable to get the clock MCLK\n");
- return PTR_ERR(h3_tsc2101.mclk);
- }
- if ((r = clk_set_rate(h3_tsc2101.mclk, 12000000)) < 0) {
- dev_err(&spi->dev, "unable to set rate to the MCLK\n");
- goto err;
- }
-
- if ((r = read_gpio_expa(&io_exp_val, 0x24))) {
- dev_err(&spi->dev, "error reading from I/O EXPANDER\n");
- goto err;
- }
- io_exp_val |= 0x8;
- if ((r = write_gpio_expa(io_exp_val, 0x24))) {
- dev_err(&spi->dev, "error writing to I/O EXPANDER\n");
- goto err;
- }
-
- omap_cfg_reg(N14_1610_UWIRE_CS0);
- omap_cfg_reg(TSC2101_MUX_MCLK_OFF);
-
- return 0;
-err:
- clk_put(h3_tsc2101.mclk);
- return r;
-}
-
-static void h3_tsc2101_cleanup(struct spi_device *spi)
-{
- clk_put(h3_tsc2101.mclk);
- omap_cfg_reg(TSC2101_MUX_MCLK_OFF);
-}
-
-static void h3_tsc2101_enable_mclk(struct spi_device *spi)
-{
- omap_cfg_reg(TSC2101_MUX_MCLK_ON);
- clk_enable(h3_tsc2101.mclk);
-}
-
-static void h3_tsc2101_disable_mclk(struct spi_device *spi)
-{
- clk_disable(h3_tsc2101.mclk);
- omap_cfg_reg(R10_1610_MCLK_OFF);
-}
-
-static struct tsc2101_platform_data h3_tsc2101_platform_data = {
- .init = h3_tsc2101_init,
- .cleanup = h3_tsc2101_cleanup,
- .enable_mclk = h3_tsc2101_enable_mclk,
- .disable_mclk = h3_tsc2101_disable_mclk,
+static struct tsc210x_config tsc_platform_data = {
+ .use_internal = 1,
+ .monitor = TSC_VBAT | TSC_TEMP,
+ .mclk = "mclk",
};
static struct spi_board_info h3_spi_board_info[] __initdata = {
@@ -452,8 +385,9 @@ static struct spi_board_info h3_spi_board_info[] __initdata = {
.modalias = "tsc2101",
.bus_num = 2,
.chip_select = 0,
+ .irq = OMAP_GPIO_IRQ(48),
.max_speed_hz = 16000000,
- .platform_data = &h3_tsc2101_platform_data,
+ .platform_data = &tsc_platform_data,
},
};
@@ -569,6 +503,12 @@ static void __init h3_init(void)
/* GPIO10 pullup/down register, Enable pullup on GPIO10 */
omap_cfg_reg(V2_1710_GPIO10);
+ /* TSC2101 */
+ omap_cfg_reg(W19_1610_GPIO48);
+ gpio_request(48, "tsc_irq");
+ gpio_direction_input(48);
+ omap_cfg_reg(N14_1610_UWIRE_CS0);
+
platform_add_devices(devices, ARRAY_SIZE(devices));
spi_register_board_info(h3_spi_board_info,
ARRAY_SIZE(h3_spi_board_info));
--
1.5.2.5
-
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
