From: Anand Gadiyar <gadiyar@xxxxxx>
Added support for TWL4030 USB transceiver chip.
Signed-off-by: Anand Gadiyar <gadiyar@xxxxxx>
Signed-off-by: Vikram Pandita <vikram.pandita@xxxxxx>
Signed-off-by: Nishant Kamat <nskamat@xxxxxx>
---
drivers/i2c/chips/Kconfig | 19 +
drivers/i2c/chips/Makefile | 3
drivers/i2c/chips/twl4030_usb.c | 700 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 721 insertions(+), 1 deletion(-)
Index: linux-omap-dec10/drivers/i2c/chips/Kconfig
===================================================================
--- linux-omap-dec10.orig/drivers/i2c/chips/Kconfig 2007-12-14 19:06:41.112941439 +0530
+++ linux-omap-dec10/drivers/i2c/chips/Kconfig 2007-12-14 19:12:45.826336129 +0530
@@ -140,6 +140,25 @@
bool "TWL4030 GPIO Driver"
depends on TWL4030_CORE
+config TWL4030_USB
+ bool "TWL4030 USB Transceiver Driver"
+ depends on TWL4030_CORE
+
+choice
+ prompt "Transceiver mode"
+ depends on TWL4030_USB
+ help
+ TWL4030 USB transceiver can operate in various
+ mutually-exclusive modes. Select one of them.
+
+config TWL4030_USB_HS_ULPI
+ depends on TWL4030_USB
+ bool "High-speed ULPI"
+ help
+ Say Y here if the TWL4030 is connected to high-speed USB
+ controller through a ULPI interface.
+endchoice
+
config SENSORS_M41T00
tristate "ST M41T00 RTC chip (DEPRECATED)"
depends on PPC32
Index: linux-omap-dec10/drivers/i2c/chips/Makefile
===================================================================
--- linux-omap-dec10.orig/drivers/i2c/chips/Makefile 2007-12-14 19:06:41.112941439 +0530
+++ linux-omap-dec10/drivers/i2c/chips/Makefile 2007-12-14 19:12:45.826336129 +0530
@@ -17,8 +17,9 @@
obj-$(CONFIG_GPIOEXPANDER_OMAP) += gpio_expander_omap.o
obj-$(CONFIG_MENELAUS) += menelaus.o
obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o
-obj-$(CONFIG_TWL4030_CORE) += twl4030_core.o
+obj-$(CONFIG_TWL4030_CORE) += twl4030_core.o
obj-$(CONFIG_TWL4030_GPIO) += twl4030_gpio.o
+obj-$(CONFIG_TWL4030_USB) += twl4030_usb.o
obj-$(CONFIG_RTC_X1205_I2C) += x1205.o
ifeq ($(CONFIG_I2C_DEBUG_CHIP),y)
Index: linux-omap-dec10/drivers/i2c/chips/twl4030_usb.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-omap-dec10/drivers/i2c/chips/twl4030_usb.c 2007-12-14 19:30:44.115082813 +0530
@@ -0,0 +1,700 @@
+/*
+ * twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller
+ *
+ * Copyright (C) 2004-2007 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Current status:
+ * - HS USB ULPI mode works.
+ * - 3-pin mode support may be added in future.
+ */
+
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/time.h>
+#include <linux/interrupt.h>
+#include <linux/usb.h>
+
+#include <asm/arch/twl4030.h>
+
+/* Register defines */
+
+#define VENDOR_ID_LO 0x00
+#define VENDOR_ID_HI 0x01
+#define PRODUCT_ID_LO 0x02
+#define PRODUCT_ID_HI 0x03
+
+#define FUNC_CTRL 0x04
+#define FUNC_CTRL_SET 0x05
+#define FUNC_CTRL_CLR 0x06
+#define FUNC_CTRL_SUSPENDM (1 << 6)
+#define FUNC_CTRL_RESET (1 << 5)
+#define FUNC_CTRL_OPMODE_MASK (3 << 3) /* bits 3 and 4 */
+#define FUNC_CTRL_OPMODE_NORMAL (0 << 3)
+#define FUNC_CTRL_OPMODE_NONDRIVING (1 << 3)
+#define FUNC_CTRL_OPMODE_DISABLE_BIT_NRZI (2 << 3)
+#define FUNC_CTRL_TERMSELECT (1 << 2)
+#define FUNC_CTRL_XCVRSELECT_MASK (3 << 0) /* bits 0 and 1 */
+#define FUNC_CTRL_XCVRSELECT_HS (0 << 0)
+#define FUNC_CTRL_XCVRSELECT_FS (1 << 0)
+#define FUNC_CTRL_XCVRSELECT_LS (2 << 0)
+#define FUNC_CTRL_XCVRSELECT_FS4LS (3 << 0)
+
+#define IFC_CTRL 0x07
+#define IFC_CTRL_SET 0x08
+#define IFC_CTRL_CLR 0x09
+#define IFC_CTRL_INTERFACE_PROTECT_DISABLE (1 << 7)
+#define IFC_CTRL_AUTORESUME (1 << 4)
+#define IFC_CTRL_CLOCKSUSPENDM (1 << 3)
+#define IFC_CTRL_CARKITMODE (1 << 2)
+#define IFC_CTRL_FSLSSERIALMODE_3PIN (1 << 1)
+
+#define OTG_CTRL 0x0A
+#define OTG_CTRL_SET 0x0B
+#define OTG_CTRL_CLR 0x0C
+#define OTG_CTRL_DRVVBUS (1 << 5)
+#define OTG_CTRL_CHRGVBUS (1 << 4)
+#define OTG_CTRL_DISCHRGVBUS (1 << 3)
+#define OTG_CTRL_DMPULLDOWN (1 << 2)
+#define OTG_CTRL_DPPULLDOWN (1 << 1)
+#define OTG_CTRL_IDPULLUP (1 << 0)
+
+#define USB_INT_EN_RISE 0x0D
+#define USB_INT_EN_RISE_SET 0x0E
+#define USB_INT_EN_RISE_CLR 0x0F
+#define USB_INT_EN_FALL 0x10
+#define USB_INT_EN_FALL_SET 0x11
+#define USB_INT_EN_FALL_CLR 0x12
+#define USB_INT_STS 0x13
+#define USB_INT_LATCH 0x14
+#define USB_INT_IDGND (1 << 4)
+#define USB_INT_SESSEND (1 << 3)
+#define USB_INT_SESSVALID (1 << 2)
+#define USB_INT_VBUSVALID (1 << 1)
+#define USB_INT_HOSTDISCONNECT (1 << 0)
+
+#define CARKIT_CTRL 0x19
+#define CARKIT_CTRL_SET 0x1A
+#define CARKIT_CTRL_CLR 0x1B
+#define CARKIT_CTRL_MICEN (1 << 6)
+#define CARKIT_CTRL_SPKRIGHTEN (1 << 5)
+#define CARKIT_CTRL_SPKLEFTEN (1 << 4)
+#define CARKIT_CTRL_RXDEN (1 << 3)
+#define CARKIT_CTRL_TXDEN (1 << 2)
+#define CARKIT_CTRL_IDGNDDRV (1 << 1)
+#define CARKIT_CTRL_CARKITPWR (1 << 0)
+#define CARKIT_PLS_CTRL 0x22
+#define CARKIT_PLS_CTRL_SET 0x23
+#define CARKIT_PLS_CTRL_CLR 0x24
+#define CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN (1 << 3)
+#define CARKIT_PLS_CTRL_SPKRLEFT_BIASEN (1 << 2)
+#define CARKIT_PLS_CTRL_RXPLSEN (1 << 1)
+#define CARKIT_PLS_CTRL_TXPLSEN (1 << 0)
+
+#define MCPC_CTRL 0x30
+#define MCPC_CTRL_SET 0x31
+#define MCPC_CTRL_CLR 0x32
+#define MCPC_CTRL_RTSOL (1 << 7)
+#define MCPC_CTRL_EXTSWR (1 << 6)
+#define MCPC_CTRL_EXTSWC (1 << 5)
+#define MCPC_CTRL_VOICESW (1 << 4)
+#define MCPC_CTRL_OUT64K (1 << 3)
+#define MCPC_CTRL_RTSCTSSW (1 << 2)
+#define MCPC_CTRL_HS_UART (1 << 0)
+
+#define MCPC_IO_CTRL 0x33
+#define MCPC_IO_CTRL_SET 0x34
+#define MCPC_IO_CTRL_CLR 0x35
+#define MCPC_IO_CTRL_MICBIASEN (1 << 5)
+#define MCPC_IO_CTRL_CTS_NPU (1 << 4)
+#define MCPC_IO_CTRL_RXD_PU (1 << 3)
+#define MCPC_IO_CTRL_TXDTYP (1 << 2)
+#define MCPC_IO_CTRL_CTSTYP (1 << 1)
+#define MCPC_IO_CTRL_RTSTYP (1 << 0)
+
+#define MCPC_CTRL2 0x36
+#define MCPC_CTRL2_SET 0x37
+#define MCPC_CTRL2_CLR 0x38
+#define MCPC_CTRL2_MCPC_CK_EN (1 << 0)
+
+#define OTHER_FUNC_CTRL 0x80
+#define OTHER_FUNC_CTRL_SET 0x81
+#define OTHER_FUNC_CTRL_CLR 0x82
+#define OTHER_FUNC_CTRL_BDIS_ACON_EN (1 << 4)
+#define OTHER_FUNC_CTRL_FIVEWIRE_MODE (1 << 2)
+
+#define OTHER_IFC_CTRL 0x83
+#define OTHER_IFC_CTRL_SET 0x84
+#define OTHER_IFC_CTRL_CLR 0x85
+#define OTHER_IFC_CTRL_OE_INT_EN (1 << 6)
+#define OTHER_IFC_CTRL_CEA2011_MODE (1 << 5)
+#define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN (1 << 4)
+#define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT (1 << 3)
+#define OTHER_IFC_CTRL_HIZ_ULPI (1 << 2)
+#define OTHER_IFC_CTRL_ALT_INT_REROUTE (1 << 0)
+
+#define OTHER_INT_EN_RISE 0x86
+#define OTHER_INT_EN_RISE_SET 0x87
+#define OTHER_INT_EN_RISE_CLR 0x88
+#define OTHER_INT_EN_FALL 0x89
+#define OTHER_INT_EN_FALL_SET 0x8A
+#define OTHER_INT_EN_FALL_CLR 0x8B
+#define OTHER_INT_STS 0x8C
+#define OTHER_INT_LATCH 0x8D
+#define OTHER_INT_VB_SESS_VLD (1 << 7)
+#define OTHER_INT_DM_HI (1 << 6) /* not valid for "latch" reg */
+#define OTHER_INT_DP_HI (1 << 5) /* not valid for "latch" reg */
+#define OTHER_INT_BDIS_ACON (1 << 3) /* not valid for "fall" regs */
+#define OTHER_INT_MANU (1 << 1)
+#define OTHER_INT_ABNORMAL_STRESS (1 << 0)
+
+#define ID_STATUS 0x96
+#define ID_RES_FLOAT (1 << 4)
+#define ID_RES_440K (1 << 3)
+#define ID_RES_200K (1 << 2)
+#define ID_RES_102K (1 << 1)
+#define ID_RES_GND (1 << 0)
+
+#define POWER_CTRL 0xAC
+#define POWER_CTRL_SET 0xAD
+#define POWER_CTRL_CLR 0xAE
+#define POWER_CTRL_OTG_ENAB (1 << 5)
+
+#define OTHER_IFC_CTRL2 0xAF
+#define OTHER_IFC_CTRL2_SET 0xB0
+#define OTHER_IFC_CTRL2_CLR 0xB1
+#define OTHER_IFC_CTRL2_ULPI_STP_LOW (1 << 4)
+#define OTHER_IFC_CTRL2_ULPI_TXEN_POL (1 << 3)
+#define OTHER_IFC_CTRL2_ULPI_4PIN_2430 (1 << 2)
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK (3 << 0) /* bits 0 and 1 */
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N (0 << 0)
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N (1 << 0)
+
+#define REG_CTRL_EN 0xB2
+#define REG_CTRL_EN_SET 0xB3
+#define REG_CTRL_EN_CLR 0xB4
+#define REG_CTRL_ERROR 0xB5
+#define ULPI_I2C_CONFLICT_INTEN (1 << 0)
+
+#define OTHER_FUNC_CTRL2 0xB8
+#define OTHER_FUNC_CTRL2_SET 0xB9
+#define OTHER_FUNC_CTRL2_CLR 0xBA
+#define OTHER_FUNC_CTRL2_VBAT_TIMER_EN (1 << 0)
+
+/* following registers do not have separate _clr and _set registers */
+#define VBUS_DEBOUNCE 0xC0
+#define ID_DEBOUNCE 0xC1
+#define VBAT_TIMER 0xD3
+#define PHY_PWR_CTRL 0xFD
+#define PHY_PWR_PHYPWD (1 << 0)
+#define PHY_CLK_CTRL 0xFE
+#define PHY_CLK_CTRL_CLOCKGATING_EN (1 << 2)
+#define PHY_CLK_CTRL_CLK32K_EN (1 << 1)
+#define REQ_PHY_DPLL_CLK (1 << 0)
+#define PHY_CLK_CTRL_STS 0xFF
+#define PHY_DPLL_CLK (1 << 0)
+
+/* In module TWL4030_MODULE_PM_MASTER */
+#define PROTECT_KEY 0x0E
+
+/* In module TWL4030_MODULE_PM_RECEIVER */
+#define VUSB_DEDICATED1 0x7D
+#define VUSB_DEDICATED2 0x7E
+#define VUSB1V5_DEV_GRP 0x71
+#define VUSB1V5_TYPE 0x72
+#define VUSB1V5_REMAP 0x73
+#define VUSB1V8_DEV_GRP 0x74
+#define VUSB1V8_TYPE 0x75
+#define VUSB1V8_REMAP 0x76
+#define VUSB3V1_DEV_GRP 0x77
+#define VUSB3V1_TYPE 0x78
+#define VUSB3V1_REMAP 0x79
+
+#define ID_STATUS 0x96
+#define ID_RES_FLOAT (1 << 4) /* mini-B */
+#define ID_RES_440K (1 << 3) /* type 2 charger */
+#define ID_RES_200K (1 << 2) /* 5-wire carkit or
+ type 1 charger */
+#define ID_RES_102K (1 << 1) /* phone */
+#define ID_RES_GND (1 << 0) /* mini-A */
+
+/* In module TWL4030_MODULE_INTBR */
+#define PMBR1 0x0D
+#define GPIO_USB_4PIN_ULPI_2430C (3 << 0)
+
+/* In module TWL4030_MODULE_INT */
+#define REG_PWR_ISR1 0x00
+#define REG_PWR_IMR1 0x01
+#define USB_PRES (1 << 2)
+#define REG_PWR_EDR1 0x05
+#define USB_PRES_FALLING (1 << 4)
+#define USB_PRES_RISING (1 << 5)
+#define REG_PWR_SIH_CTRL 0x07
+#define COR (1 << 2)
+
+/*-------------------------------------------------------------------------*/
+
+static int twl4030_i2c_write_u8_verify(u8 module, u8 data, u8 address)
+{
+ u8 check;
+ if ((twl4030_i2c_write_u8(module, data, address) >= 0) &&
+ (twl4030_i2c_read_u8(module, &check, address) >= 0) &&
+ (check == data))
+ return 0;
+ /* Failed once: Try again */
+ if ((twl4030_i2c_write_u8(module, data, address) >= 0) &&
+ (twl4030_i2c_read_u8(module, &check, address) >= 0) &&
+ (check == data))
+ return 0;
+ /* Failed again: Return error */
+ return -EBUSY;
+}
+
+#define twl4030_usb_write_verify(address, data) \
+ twl4030_i2c_write_u8_verify(TWL4030_MODULE_USB, (data), (address))
+
+static inline int twl4030_usb_write(u8 address, u8 data)
+{
+ int ret = 0;
+ ret = twl4030_i2c_write_u8(TWL4030_MODULE_USB, data, address);
+ if (ret >= 0) {
+#if 0 /* debug */
+ u8 data1;
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_USB, &data1,
+ address) < 0)
+ printk(KERN_ERR "re-read failed\n");
+ else
+ printk(KERN_INFO
+ "Write %s wrote %x read %x from reg %x\n",
+ (data1 == data) ? "succeed" : "mismatch",
+ data, data1, address);
+#endif
+ } else {
+ printk(KERN_WARNING
+ "TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
+ }
+ return ret;
+}
+
+static inline int twl4030_usb_read(u8 address)
+{
+ u8 data;
+ int ret = 0;
+ ret = twl4030_i2c_read_u8(TWL4030_MODULE_USB, &data, address);
+ if (ret >= 0) {
+ ret = data;
+ } else {
+ printk(KERN_WARNING
+ "TWL4030:USB:Read[0x%x] Error %d\n", address, ret);
+ }
+ return ret;
+}
+
+/*-------------------------------------------------------------------------*/
+
+struct twl4030_usb {
+ int irq;
+ u8 usb_mode; /* pin configuration */
+#define T2_USB_MODE_ULPI 1
+/* #define T2_USB_MODE_CEA2011_3PIN 2 */
+ u8 asleep;
+};
+
+static struct twl4030_usb *the_transceiver;
+
+/*-------------------------------------------------------------------------*/
+
+static inline int
+twl4030_usb_set_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
+{
+ return twl4030_usb_write(reg + 1, bits);
+}
+
+static inline int
+twl4030_usb_clear_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
+{
+ return twl4030_usb_write(reg + 2, bits);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static void twl4030_usb_set_mode(struct twl4030_usb *twl, int mode)
+{
+ twl->usb_mode = mode;
+
+ switch (mode) {
+ case T2_USB_MODE_ULPI:
+ twl4030_usb_clear_bits(twl, IFC_CTRL, IFC_CTRL_CARKITMODE);
+ twl4030_usb_set_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
+ twl4030_usb_clear_bits(twl, FUNC_CTRL,
+ FUNC_CTRL_XCVRSELECT_MASK |
+ FUNC_CTRL_OPMODE_MASK);
+ break;
+/*
+ case T2_USB_MODE_CEA2011_3PIN:
+ twl4030_cea2011_3_pin_FS_setup(twl);
+ break;
+*/
+ default:
+ /* FIXME: power on defaults */
+ break;
+ };
+}
+
+#ifdef CONFIG_TWL4030_USB_HS_ULPI
+static void hs_usb_init(struct twl4030_usb *twl)
+{
+ twl->usb_mode = T2_USB_MODE_ULPI;
+ return;
+}
+
+#endif
+
+static void twl4030_i2c_access(int on)
+{
+ unsigned long timeout;
+ int val = twl4030_usb_read(PHY_CLK_CTRL);
+
+ if (val >= 0) {
+ if (on) {
+ /* enable DPLL to access PHY registers over I2C */
+ val |= REQ_PHY_DPLL_CLK;
+ if (twl4030_usb_write_verify(PHY_CLK_CTRL,
+ (u8)val) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c write failed,"
+ "line %d\n", __LINE__);
+ return;
+ }
+
+ timeout = jiffies + HZ;
+ while (!(twl4030_usb_read(PHY_CLK_CTRL_STS) &
+ PHY_DPLL_CLK)
+ && time_before(jiffies, timeout))
+ udelay(10);
+ if (!(twl4030_usb_read(PHY_CLK_CTRL_STS) &
+ PHY_DPLL_CLK))
+ printk(KERN_ERR "Timeout setting T2 HSUSB "
+ "PHY DPLL clock\n");
+ } else {
+ /* let ULPI control the DPLL clock */
+ val &= ~REQ_PHY_DPLL_CLK;
+ if (twl4030_usb_write_verify(PHY_CLK_CTRL,
+ (u8)val) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c write failed,"
+ "line %d\n", __LINE__);
+ }
+ }
+ }
+ return;
+}
+
+static void usb_irq_enable(int rising, int falling)
+{
+ u8 val;
+
+ /* edge setup */
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_EDR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c read failed,"
+ "line %d\n", __LINE__);
+ return;
+ }
+ val &= ~(USB_PRES_RISING | USB_PRES_FALLING);
+ if (rising)
+ val = val | USB_PRES_RISING;
+ if (falling)
+ val = val | USB_PRES_FALLING;
+ if (twl4030_i2c_write_u8_verify(TWL4030_MODULE_INT, val,
+ REG_PWR_EDR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c write failed,"
+ "line %d\n", __LINE__);
+ return;
+ }
+
+ /* un-mask interrupt */
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_IMR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c read failed,"
+ "line %d\n", __LINE__);
+ return;
+ }
+ val &= ~USB_PRES;
+ if (twl4030_i2c_write_u8_verify(TWL4030_MODULE_INT, val,
+ REG_PWR_IMR1) < 0)
+ printk(KERN_ERR "twl4030_usb: i2c write failed,"
+ "line %d\n", __LINE__);
+
+ return;
+}
+
+static void usb_irq_disable(void)
+{
+ u8 val;
+
+ /* undo edge setup */
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_EDR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c read failed,"
+ "line %d\n", __LINE__);
+ return;
+ }
+ val &= ~(USB_PRES_RISING | USB_PRES_FALLING);
+ if (twl4030_i2c_write_u8_verify(TWL4030_MODULE_INT, val,
+ REG_PWR_EDR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c write failed,"
+ "line %d\n", __LINE__);
+ return;
+ }
+
+ /* mask interrupt */
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_IMR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c read failed,"
+ "line %d\n", __LINE__);
+ return;
+ }
+ val |= USB_PRES;
+ if (twl4030_i2c_write_u8_verify(TWL4030_MODULE_INT, val,
+ REG_PWR_IMR1) < 0)
+ printk(KERN_ERR "twl4030_usb: i2c write failed,"
+ "line %d\n", __LINE__);
+
+ return;
+}
+
+void twl4030_phy_suspend(int controller_off);
+void twl4030_phy_resume(void);
+
+static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
+{
+ int ret = IRQ_NONE;
+ u8 val;
+ u8 sih_ctrl;
+
+ /* save previous value of SIH_CTRL and disable clear_on_read */
+ twl4030_i2c_read_u8(TWL4030_MODULE_INT, &sih_ctrl, REG_PWR_SIH_CTRL);
+ twl4030_i2c_write_u8(TWL4030_MODULE_INT, (sih_ctrl & ~COR),
+ REG_PWR_SIH_CTRL);
+
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_ISR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c read failed,"
+ "line %d\n", __LINE__);
+ goto done;
+ }
+
+ /* this interrupt line may be shared */
+ if (!(val & USB_PRES))
+ goto done;
+
+ /* clear the interrupt */
+ twl4030_i2c_write_u8(TWL4030_MODULE_INT, USB_PRES, REG_PWR_ISR1);
+
+ /* action based on cable attach or detach */
+ if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_EDR1) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c read failed,"
+ "line %d\n", __LINE__);
+ goto done;
+ }
+
+ if (val & USB_PRES_RISING)
+ twl4030_phy_resume();
+ else
+ twl4030_phy_suspend(0);
+
+ ret = IRQ_HANDLED;
+
+done:
+ /* restore previous value of SIH_CTRL */
+ twl4030_i2c_write_u8(TWL4030_MODULE_INT, sih_ctrl, REG_PWR_SIH_CTRL);
+ return ret;
+}
+
+static void twl4030_phy_power(struct twl4030_usb *twl, int on)
+{
+ u8 pwr;
+
+ pwr = twl4030_usb_read(PHY_PWR_CTRL);
+ if (on) {
+ pwr &= ~PHY_PWR_PHYPWD;
+ if (twl4030_usb_write_verify(PHY_PWR_CTRL, pwr) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c write failed,"
+ "line %d\n", __LINE__);
+ return;
+ }
+ twl4030_usb_write(PHY_CLK_CTRL,
+ twl4030_usb_read(PHY_CLK_CTRL) |
+ (PHY_CLK_CTRL_CLOCKGATING_EN |
+ PHY_CLK_CTRL_CLK32K_EN));
+ } else {
+ pwr |= PHY_PWR_PHYPWD;
+ if (twl4030_usb_write_verify(PHY_PWR_CTRL, pwr) < 0) {
+ printk(KERN_ERR "twl4030_usb: i2c write failed,"
+ "line %d\n", __LINE__);
+ }
+ }
+ return;
+}
+
+static void twl4030_usb_ldo_init(struct twl4030_usb *twl)
+{
+ /* Enable writing to power configuration registers */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0xC0, PROTECT_KEY);
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0x0C, PROTECT_KEY);
+
+ /* put VUSB3V1 LDO in active state */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB_DEDICATED2);
+
+ /* input to VUSB3V1 LDO is from VBAT, not VBUS */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x14, VUSB_DEDICATED1);
+
+ /* turn on 3.1V regulator */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB3V1_DEV_GRP);
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB3V1_TYPE);
+
+ /* turn on 1.5V regulator */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB1V5_DEV_GRP);
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V5_TYPE);
+
+ /* turn on 1.8V regulator */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x20, VUSB1V8_DEV_GRP);
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, VUSB1V8_TYPE);
+
+ /* disable access to power configuration registers */
+ twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0, PROTECT_KEY);
+}
+
+void twl4030_phy_suspend(int controller_off)
+{
+ struct twl4030_usb *twl = the_transceiver;
+
+ if (controller_off)
+ usb_irq_disable();
+
+ if (twl->asleep)
+ return;
+
+ if (!controller_off)
+ /* enable rising edge interrupt to detect cable attach */
+ usb_irq_enable(1, 0);
+
+ twl4030_phy_power(twl, 0);
+ twl->asleep = 1;
+ return;
+}
+EXPORT_SYMBOL(twl4030_phy_suspend);
+
+
+void twl4030_phy_resume(void)
+{
+ struct twl4030_usb *twl = the_transceiver;
+
+ if (!twl->asleep)
+ return;
+
+ /* enable falling edge interrupt to detect cable detach */
+ usb_irq_enable(0, 1);
+
+ twl4030_phy_power(twl, 1);
+ twl4030_i2c_access(1);
+ twl4030_usb_set_mode(twl, twl->usb_mode);
+ if (twl->usb_mode == T2_USB_MODE_ULPI)
+ twl4030_i2c_access(0);
+ twl->asleep = 0;
+ return;
+}
+EXPORT_SYMBOL(twl4030_phy_resume);
+
+
+static int __init twl4030_usb_init(void)
+{
+ struct twl4030_usb *twl;
+ int status;
+
+ if (the_transceiver)
+ return 0;
+
+ twl = kcalloc(1, sizeof *twl, GFP_KERNEL);
+ if (!twl)
+ return 0;
+
+ the_transceiver = twl;
+
+ twl->irq = TWL4030_MODIRQ_PWR;
+
+ usb_irq_disable();
+ status = request_irq(twl->irq, twl4030_usb_irq,
+ IRQF_DISABLED | IRQF_SHARED, "twl4030_usb", twl);
+ if (status < 0) {
+ printk(KERN_DEBUG "can't get IRQ %d, err %d\n",
+ twl->irq, status);
+ kfree(twl);
+ return -ENODEV;
+ }
+
+#if defined(CONFIG_TWL4030_USB_HS_ULPI)
+ hs_usb_init(twl);
+#endif
+ twl4030_usb_ldo_init(twl);
+ twl4030_phy_power(twl, 1);
+ twl4030_i2c_access(1);
+ twl4030_usb_set_mode(twl, twl->usb_mode);
+ if (twl->usb_mode == T2_USB_MODE_ULPI)
+ twl4030_i2c_access(0);
+
+ twl->asleep = 0;
+
+ if (twl->usb_mode == T2_USB_MODE_ULPI)
+ twl4030_phy_suspend(1);
+
+ printk(KERN_INFO "Initialized TWL4030 USB module");
+
+ return 0;
+}
+
+
+static void __exit twl4030_usb_exit(void)
+{
+ struct twl4030_usb *twl = the_transceiver;
+ int val;
+
+ usb_irq_disable();
+ free_irq(twl->irq, twl);
+
+ /* set transceiver mode to power on defaults */
+ twl4030_usb_set_mode(twl, -1);
+
+ /* autogate 60MHz ULPI clock,
+ * clear dpll clock request for i2c access,
+ * disable 32KHz
+ */
+ val = twl4030_usb_read(PHY_CLK_CTRL);
+ if (val >= 0) {
+ val |= PHY_CLK_CTRL_CLOCKGATING_EN;
+ val &= ~(PHY_CLK_CTRL_CLK32K_EN | REQ_PHY_DPLL_CLK);
+ twl4030_usb_write(PHY_CLK_CTRL, (u8)val);
+ }
+
+ /* disable complete OTG block */
+ twl4030_usb_clear_bits(twl, POWER_CTRL, POWER_CTRL_OTG_ENAB);
+
+ twl4030_phy_power(twl, 0);
+
+ kfree(twl);
+}
+
+subsys_initcall(twl4030_usb_init);
+module_exit(twl4030_usb_exit);
+
+MODULE_AUTHOR("Texas Instruments, Inc.");
+MODULE_DESCRIPTION("TWL4030 USB transceiver driver");
+MODULE_LICENSE("GPL");
-
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
