Hi,
It is a bad day we have 5 devices failed NAND booting all of certain
today. The 5 devices running kernel 4.19.75 on iMX6ULL customized
board, the devices had been running for weeks, the device DC power is
supplied from AC via ADC and regulator, we turned power on and off
several times when installing those test devices to test boxes in the
last couple of days without problems, then they all failed together
mysteriously today. It could not complete the booting to Linux user
space, so I am not able to log into the user space to check and to
debug it.
Here is some more background information, those 5 devices are from the
same new hardware reversion which changed a new power regulator, they
installed the same firmware kernel 4.19 building from Yocto.
Another fact, there are several old hardware reversion devices (using
different power regulator) installed the same version of kernel and
MTD, but different versions of high level applications in the same
test box, which are all running fine. So it ruled out power surge to
cause the problem.
I try to figure out the source of the problem whether it is caused by
firmware or buy hardware, as it is in very low level, I doubt the high
level applications could contribute the problem, but I could be wrong.
There were some NAND bad blocks, I am not sure if that could cause the
booting corruption. The Yocto image was built from the same Yocto
build system, I am not clear if the Yocto image could cause the NAND
corruption or not. Also, could using NAND fastmap cause the problem?
Attached following booting message, appreciate your insight comments.
Welcome to minicom 2.7.1
OPTIONS:
Compiled on Aug 20 2018, 10:22:42.
Port /dev/cu.usbserial-FTAPPVUJ, 11:47:55
Press Meta-Z for help on special keys
??????
U-Boot 2018.03-g6ce2bc2ae2 (Jan 17 2020 - 00:57:41 +0000)
CPU: Freescale i.MX6ULZ rev1.1 900 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 56C
Reset cause: POR
Model: Freescale i.MX6 ULZ 14x14 EVK Board
Board: MX6ULZ 14x14 EVK
DRAM: 512 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
Loading Environment from NAND... *** Warning - bad CRC, using default
environment
Failed (-5)
No panel detected: default to TFT43AB
Display: TFT43AB (480x272)
Video: LCDIF@0x21c8000 is fused, disable it
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Normal Boot
Hit any key to stop autoboot: 0
Booting image 1
NAND read: device 0 offset 0x800000, size 0x2000000
33554432 bytes read: OK
NAND read: device 0 offset 0x600000, size 0x200000
2097152 bytes read: OK
Kernel image @ 0x80800000 [ 0x000000 - 0x7f09d0 ]
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Using Device Tree in place at 83000000, end 83008972
ft_system_setup for mx6
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.75 (oe-user@oe-host) (gcc version
8.2.0 (GCC)) #1 SMP Fri Nov 8 06:519
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: Traverse PMU RevC
[ 0.000000] earlycon: ec_imx6q0 at MMIO 0x02020000 (options '')
[ 0.000000] bootconsole [ec_imx6q0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 64 MiB at 0x8c000000
[ 0.000000] random: get_random_bytes called from
start_kernel+0x8c/0x48c with crng_init=0
[ 0.000000] percpu: Embedded 18 pages/cpu s41896 r8192 d23640 u73728
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttymxc0,115200 earlycon
mtdparts=gpmi-nand:4m(boot),2m(uboo1
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 169124K/262144K available (11264K kernel code,
881K rwdata, 3664K rodata, 1024K )
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 882 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7649 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Running RCU self tests
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU lockdep checking is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000022] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps
every 89478484971ns
[ 0.007844] clocksource: mxc_timer1: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 796358519s
[ 0.020292] Console: colour dummy device 80x30
[ 0.021978] Lock dependency validator: Copyright (c) 2006 Red Hat,
Inc., Ingo Molnar
[ 0.030048] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.033798] ... MAX_LOCK_DEPTH: 48
[ 0.037971] ... MAX_LOCKDEP_KEYS: 8191
[ 0.042436] ... CLASSHASH_SIZE: 4096
[ 0.046672] ... MAX_LOCKDEP_ENTRIES: 32768
[ 0.051108] ... MAX_LOCKDEP_CHAINS: 65536
[ 0.055644] ... CHAINHASH_SIZE: 32768
[ 0.059983] memory used by lock dependency info: 4655 kB
[ 0.065378] per task-struct memory footprint: 1536 bytes
[ 0.070985] Calibrating delay loop (skipped), value calculated
using timer frequency.. 48.00 BogoMIP)
[ 0.081242] pid_max: default: 32768 minimum: 301
[ 0.086598] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092513] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.103902] CPU: Testing write buffer coherency: ok
[ 0.108359] /cpus/cpu@0 missing clock-frequency property
[ 0.111490] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.123335] Setting up static identity map for 0x80100000 - 0x80100078
[ 0.128797] rcu: Hierarchical SRCU implementation.
[ 0.137850] smp: Bringing up secondary CPUs ...
[ 0.139607] smp: Brought up 1 node, 1 CPU
[ 0.143604] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[ 0.149934] CPU: All CPU(s) started in SVC mode.
[ 0.159781] devtmpfs: initialized
[ 0.202335] VFP support v0.3: implementor 41 architecture 2 part 30
variant 7 rev 5
[ 0.209235] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 191126044627s
[ 0.217465] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.230315] pinctrl core: initialized pinctrl subsystem
[ 0.242556] NET: Registered protocol family 16
[ 0.324620] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.337326] cpuidle: using governor menu
[ 0.380108] vdd3p0: supplied by regulator-dummy
[ 0.386436] cpu: supplied by regulator-dummy
[ 0.392527] vddsoc: supplied by regulator-dummy
[ 0.444794] No ATAGs?
[ 0.445397] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4
watchpoint registers.
[ 0.453188] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.471287] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.477738] imx6ul-pinctrl 2290000.iomuxc-snvs: no groups defined
in /soc/aips-bus@2200000/iomuxc-sn0
[ 0.485316] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX
pinctrl driver
[ 0.659193] mxs-dma 1804000.dma-apbh: initialized
[ 0.672898] vgaarb: loaded
[ 0.676307] SCSI subsystem initialized
[ 0.680972] usbcore: registered new interface driver usbfs
[ 0.684197] usbcore: registered new interface driver hub
[ 0.690015] usbcore: registered new device driver usb
[ 0.698122] media: Linux media interface: v0.10
[ 0.700421] videodev: Linux video capture interface: v2.00
[ 0.706461] pps_core: LinuxPPS API ver. 1 registered
[ 0.710524] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <giometti@xxxxxxxx>
[ 0.719590] PTP clock support registered
[ 0.725896] Advanced Linux Sound Architecture Driver Initialized.
[ 0.735897] Bluetooth: Core ver 2.22
[ 0.736983] NET: Registered protocol family 31
[ 0.741129] Bluetooth: HCI device and connection manager initialized
[ 0.747893] Bluetooth: HCI socket layer initialized
[ 0.752390] Bluetooth: L2CAP socket layer initialized
[ 0.758035] Bluetooth: SCO socket layer initialized
[ 0.767559] clocksource: Switched to clocksource mxc_timer1
[ 1.441132] VFS: Disk quotas dquot_6.6.0
[ 1.442713] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.530381] NET: Registered protocol family 2
[ 1.536966] tcp_listen_portaddr_hash hash table entries: 128
(order: 0, 5120 bytes)
[ 1.542545] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.549492] TCP bind hash table entries: 2048 (order: 4, 73728 bytes)
[ 1.555907] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.563100] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 1.568026] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 1.575032] NET: Registered protocol family 1
[ 1.584008] RPC: Registered named UNIX socket transport module.
[ 1.587224] RPC: Registered udp transport module.
[ 1.592175] RPC: Registered tcp transport module.
[ 1.596597] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.622774] Initialise system trusted keyrings
[ 1.626159] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 1.682563] NFS: Registering the id_resolver key type
[ 1.685086] Key type id_resolver registered
[ 1.689525] Key type id_legacy registered
[ 1.693431] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.703874] fuse init (API version 7.27)
[ 1.751880] Key type asymmetric registered
[ 1.753433] Asymmetric key parser 'x509' registered
[ 1.760327] io scheduler noop registered
[ 1.761997] io scheduler deadline registered
[ 1.767245] io scheduler cfq registered (default)
[ 1.771508] io scheduler mq-deadline registered
[ 1.775474] io scheduler kyber registered
[ 1.824841] imx-sdma 20ec000.sdma: Direct firmware load for
imx/sdma/sdma-imx6q.bin failed with erro2
[ 1.832280] imx-sdma 20ec000.sdma: external firmware not found,
using ROM firmware
[ 1.851955] console [ttymxc0] enabled
[ 1.855858] bootconsole [ec_imx6q0] disabled
[ 1.869926] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 49,
base_baud = 5000000) is a IMX
[ 1.884516] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 50,
base_baud = 5000000) is a IMX
[ 2.002621] brd: module loaded
[ 2.080376] loop: module loaded
[ 2.109170] random: fast init done
[ 2.141063] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xda
[ 2.147794] nand: Winbond W29N02GV
[ 2.151330] nand: 256 MiB, SLC, erase size: 128 KiB, page size:
2048, OOB size: 64
[ 2.165475] Bad block table found at page 131008, version 0x01
[ 2.173020] Bad block table found at page 130944, version 0x01
[ 2.180892] 6 cmdlinepart partitions found on MTD device gpmi-nand
[ 2.187223] Creating 6 MTD partitions on "gpmi-nand":
[ 2.192661] 0x000000000000-0x000000400000 : "boot"
[ 2.214714] 0x000000400000-0x000000600000 : "ubootenv"
[ 2.231187] 0x000000600000-0x000000800000 : "dtb"
[ 2.246842] 0x000000800000-0x000002800000 : "kernel1"
[ 2.311648] 0x000002800000-0x000004800000 : "kernel2"
[ 2.376299] 0x000004800000-0x000010000000 : "ubi"
[ 2.684250] gpmi-nand 1806000.gpmi-nand: driver registered.
[ 2.700166] libphy: Fixed MDIO Bus: probed
[ 2.708597] CAN device driver interface
[ 2.720153] usbcore: registered new interface driver asix
[ 2.725978] usbcore: registered new interface driver ax88179_178a
[ 2.732720] usbcore: registered new interface driver cdc_ether
[ 2.739153] usbcore: registered new interface driver net1080
[ 2.745207] usbcore: registered new interface driver cdc_subset
[ 2.751721] usbcore: registered new interface driver zaurus
[ 2.758081] usbcore: registered new interface driver cdc_ncm
[ 2.764143] usbcore: registered new interface driver qmi_wwan
[ 2.770205] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.776866] ehci-pci: EHCI PCI platform driver
[ 2.781887] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 2.789587] usbcore: registered new interface driver cdc_wdm
[ 2.795868] usbcore: registered new interface driver usb-storage
[ 3.442670] mxs_phy 20c9000.usbphy: Data pin can't make good contact.
[ 3.455664] imx_usb 2184200.usb: 2184200.usb supply vbus not found,
using dummy regulator
[ 3.466393] imx_usb 2184200.usb: Linked as a consumer to regulator.0
[ 3.479980] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 3.485507] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 3.517779] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 3.533486] hub 1-0:1.0: USB hub found
[ 3.538773] hub 1-0:1.0: 1 port detected
[ 3.560890] input: 20cc000.snvs:snvs-powerkey as
/devices/soc0/soc/2000000.aips-bus/20cc000.snvs/20c0
[ 3.593166] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered
20cc000.snvs:snvs-rtc-lp as rtc0
[ 3.603922] i2c /dev entries driver
[ 3.626515] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[ 3.634895] Bluetooth: HCI UART driver ver 2.3
[ 3.639725] Bluetooth: HCI UART protocol H4 registered
[ 3.646246] Bluetooth: HCI UART protocol LL registered
[ 3.661035] sdhci: Secure Digital Host Controller Interface driver
[ 3.667585] sdhci: Copyright(c) Pierre Ossman
[ 3.672061] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.682821] sdhci-esdhc-imx 2190000.usdhc: Linked as a consumer to
regulator.4
[ 3.731410] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc]
using ADMA
[ 3.755207] usbcore: registered new interface driver usbhid
[ 3.761180] usbhid: USB HID core driver
[ 3.841803] mmc0: new high speed SDIO card at address 0001
[ 3.853262] NET: Registered protocol family 10
[ 3.871111] Segment Routing with IPv6
[ 3.875518] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.887265] NET: Registered protocol family 17
[ 3.892554] can: controller area network core (rev 20170425 abi 9)
[ 3.899993] NET: Registered protocol family 29
[ 3.904608] can: raw protocol (rev 20170425)
[ 3.909486] can: broadcast manager protocol (rev 20170425 t)
[ 3.915347] can: netlink gateway (rev 20170425) max_hops=1
[ 3.923735] Key type dns_resolver registered
[ 3.933594] cpu cpu0: Linked as a consumer to regulator.2
[ 3.940306] cpu cpu0: Linked as a consumer to regulator.3
[ 3.951480] cpu cpu0: failed to disable 696MHz OPP
[ 3.962215] Registering SWP/SWPB emulation handler
[ 3.974089] Loading compiled-in X.509 certificates
[ 4.091219] imx_thermal tempmon: Commercial CPU temperature grade -
max:95C critical:90C passive:85C
[ 4.105067] ubi0: default fastmap pool size: 70
[ 4.110009] ubi0: default fastmap WL pool size: 35
[ 4.114863] ubi0: attaching mtd5
[ 5.699392] ubi0: scanning is finished
[ 5.729392] ubi0: attached mtd5 (name "ubi", size 184 MiB)
[ 5.734965] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.742078] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.749091] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.756111] ubi0: good PEBs: 1468, bad PEBs: 4, corrupted PEBs: 0
[ 5.762353] ubi0: user volume: 1, internal volumes: 1, max. volumes
count: 128
[ 5.769725] ubi0: max/mean erase counter: 1/0, WL threshold: 4096,
image sequence number: 2012832169
[ 5.779000] ubi0: available PEBs: 104, total reserved PEBs: 1364,
PEBs reserved for bad PEB handling6
[ 5.789597] ubi0: background thread "ubi_bgt0d" started, PID 63
[ 5.797608] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock
to 1970-01-01 00:00:02 UTC (2)
[ 5.807115] cfg80211: Loading compiled-in X.509 certificates for
regulatory database
[ 5.824472] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.833748] ALSA device list:
[ 5.836790] No soundcards found.
[ 5.841708] platform regulatory.0: Direct firmware load for
regulatory.db failed with error -2
[ 5.850691] cfg80211: failed to load regulatory.db
[ 5.906636] random: crng init done
[ 5.915558] UBIFS (ubi0:0): recovery needed
[ 6.777033] UBIFS (ubi0:0): recovery deferred
[ 6.782640] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0,
name "rootfs_data", R/O mode
[ 6.791634] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB),
min./max. I/O unit sizes: 2048 bytes/2s
[ 6.801709] UBIFS (ubi0:0): FS size: 166338560 bytes (158 MiB, 1310
LEBs), journal size 8380416 byte)
[ 6.812543] UBIFS (ubi0:0): reserved for root: 4952683 bytes (4836 KiB)
[ 6.819293] UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0),
UUID 88DD740C-C81A-4579-A6CC-721Al
[ 6.836415] VFS: Mounted root (ubifs filesystem) readonly on device 0:13.
[ 6.847946] devtmpfs: mounted
[ 6.854231] Freeing unused kernel memory: 1024K
[ 6.860023] Run /sbin/init as init process
[ 7.499562] systemd[1]: System time before build time, advancing clock.
[ 7.679364] systemd[1]: systemd 239 running in system mode. (-PAM
-AUDIT -SELINUX +IMA -APPARMOR +SM)
[ 7.705865] systemd[1]: Detected architecture arm.
Welcome to OpenEmbedded nodistro.0!
[ 7.775814] systemd[1]: Set hostname to <solar>.
[ 8.733396] systemd[1]: File
/lib/systemd/system/systemd-journald.service:36 configures an IP
firewa.
[ 8.752243] systemd[1]: Proceeding WITHOUT firewalling in effect!
(This warning is only shown for th)
[ 9.498046] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 9.553931] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 9.575093] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 9.653485] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 9.706431] systemd[77]: sys-kernel-debug.mount: Failed to execute
command: No such file or directory
[ 9.721420] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
Mounting Temporary Directory (/tmp)...
[ OK ] Listening on Network Service N[ 9.819279] systemd[78]:
tmp.mount: Failed to execute commandy
etlink Socket.
Starting Journal Service...
Starting Apply Kernel Variables...
Mounting FUSE Control File System...
[ 10.031009] systemd[82]: sys-fs-fuse-connections.mount: Failed to
execute command: No such file or dy
[ OK ] Reached target Remote File Systems.
[ OK ] Created slice User and Session Slice.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Reached target Slices.
[ OK ] Created slice system-getty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
Starting File System Check on Root Device...
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on udev Control Socket.
Starting udev Coldplug all Devices...
[ OK ] Reached target Host and Network Name Lookups.
[ 10.379141] systemd[84]: systemd-udev-trigger.service: Failed to
execute command: No such file or diy
[FAILED] Failed to mount Kernel Debug File System.
See 'systemctl status sys-kernel-debug.mount' for details.
[FAILED] Failed to mount Temporary Directory (/tmp).
See 'systemctl status tmp.mount' for details.
[DEPEND] Dependency failed for Network Service.
[DEPEND] Dependency failed for Network Time Synchronization.
[ OK ] Started Journal Service.
[ OK ] Started Apply Kernel Variables.
[FAILED] Failed to mount FUSE Control File System.
See 'systemctl status sys-fs-fuse-connections.mount' for details.
[ OK ] Started File System Check on Root Device.
[FAILED] Failed to start udev Coldplug all Devices.
See 'systemctl status systemd-udev-trigger.service' for details.
[ OK ] Reached target System Time Synchronized.
Starting Remount Root and Kernel File Systems...
[FAILED] Failed to start Remount Root and Kernel File Systems.
See 'systemctl status systemd-remount-fs.service' for details.
Starting Flush Journal to Persistent Storage...
Starting Create Static Device Nodes in /dev...
[FAILED] Failed to start Flush Journal to Persistent Storage.
See 'systemctl status systemd-journal-flush.service' for details.
[FAILED] Failed to start Create Static Device Nodes in /dev.
See 'systemctl status systemd-tmpfiles-setup-dev.service' for details.
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
Mounting /var/volatile...
[ OK ] Reached target Containers.
[FAILED] Failed to mount /var/volatile.
See 'systemctl status var-volatile.mount' for details.
[DEPEND] Dependency failed for Bind mount volatile /var/cache.
[DEPEND] Dependency failed for Bind mount volatile /srv.
[DEPEND] Dependency failed for Bind mount volatile /var/spool.
[DEPEND] Dependency failed for Bind mount volatile /var/lib.
[DEPEND] Dependency failed for Local File Systems.
[ OK ] Reached target Network.
[ OK ] Reached target Login Prompts.
[ OK ] Reached target Timers.
[ OK ] Reached target Sockets.
[ OK ] Started Emergency Shell.
[ OK ] Reached target Emergency Mode.
Starting Create Volatile Files and Directories...
Starting Load/Save Random Seed...
[ OK ] Started udev Kernel Device Manager.
[FAILED] Failed to start Create Volatile Files and Directories.
See 'systemctl status systemd-tmpfiles-setup.service' for details.
[ OK ] Started Load/Save Random Seed.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Update UTMP about System Boot/Shutdown.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Started Update UTMP about System Runlevel Changes.
You are in emergency mode. After logging in, type "journalctl -xb" to view
system logs, "systemctl reboot" to reboot, "systemctl default" or "exit"
to boot into default mode.
Press Enter for maintenance
(or press Control-D to continue):
Thank you.
Kind regards,
- jh
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Corruped NAND booting for all devices
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Corruped NAND booting for all devices
- From: JH <jupiter.hce@xxxxxxxxx>
- Date: Wed, 5 Feb 2020 12:43:36 +1100
- Follow-Ups:
- Re: Corruped NAND booting for all devices
- From: Jef Driesen
- Re: Corruped NAND booting for all devices
- From: Steve deRosier
- Re: Corruped NAND booting for all devices
- Prev by Date: Re: Implementing quota support on Linux without block device as backing store ? / was: RE: [PATCH 1/8] quota: Allow to pass mount path to quotactl
- Next by Date: Re: Corruped NAND booting for all devices
- Previous by thread: Implementing quota support on Linux without block device as backing store ? / was: RE: [PATCH 1/8] quota: Allow to pass mount path to quotactl
- Next by thread: Re: Corruped NAND booting for all devices
- Index(es):
 |