This moves the whole driver into a single C file. The filename gpmi-lib
implies that it implements library functions, but in fact there are
several cases where functions in gpmi-lib.c call back into functions in
gpmi-nand.c. With this one has to constantly jump between those two
files, so moving it into a single file improves readability, even when
the file gets quite large.
Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
Reviewed-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
---
drivers/mtd/nand/raw/gpmi-nand/Makefile | 1 -
drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c | 923 --------------
drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c | 1269 +++++++++++++++++---
drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h | 34 -
4 files changed, 1095 insertions(+), 1132 deletions(-)
diff --git a/drivers/mtd/nand/raw/gpmi-nand/Makefile b/drivers/mtd/nand/raw/gpmi-nand/Makefile
index 3a462487c35e..60c7b6f87c53 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/Makefile
+++ b/drivers/mtd/nand/raw/gpmi-nand/Makefile
@@ -1,3 +1,2 @@
obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi_nand.o
gpmi_nand-objs += gpmi-nand.o
-gpmi_nand-objs += gpmi-lib.o
diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
index a8b26d2e793c..bcc92185384a 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
@@ -9,926 +9,3 @@
#include <linux/clk.h>
#include <linux/slab.h>
-#include "gpmi-nand.h"
-#include "gpmi-regs.h"
-#include "bch-regs.h"
-
-/* Converts time to clock cycles */
-#define TO_CYCLES(duration, period) DIV_ROUND_UP_ULL(duration, period)
-
-#define MXS_SET_ADDR 0x4
-#define MXS_CLR_ADDR 0x8
-/*
- * Clear the bit and poll it cleared. This is usually called with
- * a reset address and mask being either SFTRST(bit 31) or CLKGATE
- * (bit 30).
- */
-static int clear_poll_bit(void __iomem *addr, u32 mask)
-{
- int timeout = 0x400;
-
- /* clear the bit */
- writel(mask, addr + MXS_CLR_ADDR);
-
- /*
- * SFTRST needs 3 GPMI clocks to settle, the reference manual
- * recommends to wait 1us.
- */
- udelay(1);
-
- /* poll the bit becoming clear */
- while ((readl(addr) & mask) && --timeout)
- /* nothing */;
-
- return !timeout;
-}
-
-#define MODULE_CLKGATE (1 << 30)
-#define MODULE_SFTRST (1 << 31)
-/*
- * The current mxs_reset_block() will do two things:
- * [1] enable the module.
- * [2] reset the module.
- *
- * In most of the cases, it's ok.
- * But in MX23, there is a hardware bug in the BCH block (see erratum #2847).
- * If you try to soft reset the BCH block, it becomes unusable until
- * the next hard reset. This case occurs in the NAND boot mode. When the board
- * boots by NAND, the ROM of the chip will initialize the BCH blocks itself.
- * So If the driver tries to reset the BCH again, the BCH will not work anymore.
- * You will see a DMA timeout in this case. The bug has been fixed
- * in the following chips, such as MX28.
- *
- * To avoid this bug, just add a new parameter `just_enable` for
- * the mxs_reset_block(), and rewrite it here.
- */
-static int gpmi_reset_block(void __iomem *reset_addr, bool just_enable)
-{
- int ret;
- int timeout = 0x400;
-
- /* clear and poll SFTRST */
- ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
- if (unlikely(ret))
- goto error;
-
- /* clear CLKGATE */
- writel(MODULE_CLKGATE, reset_addr + MXS_CLR_ADDR);
-
- if (!just_enable) {
- /* set SFTRST to reset the block */
- writel(MODULE_SFTRST, reset_addr + MXS_SET_ADDR);
- udelay(1);
-
- /* poll CLKGATE becoming set */
- while ((!(readl(reset_addr) & MODULE_CLKGATE)) && --timeout)
- /* nothing */;
- if (unlikely(!timeout))
- goto error;
- }
-
- /* clear and poll SFTRST */
- ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
- if (unlikely(ret))
- goto error;
-
- /* clear and poll CLKGATE */
- ret = clear_poll_bit(reset_addr, MODULE_CLKGATE);
- if (unlikely(ret))
- goto error;
-
- return 0;
-
-error:
- pr_err("%s(%p): module reset timeout\n", __func__, reset_addr);
- return -ETIMEDOUT;
-}
-
-static int __gpmi_enable_clk(struct gpmi_nand_data *this, bool v)
-{
- struct clk *clk;
- int ret;
- int i;
-
- for (i = 0; i < GPMI_CLK_MAX; i++) {
- clk = this->resources.clock[i];
- if (!clk)
- break;
-
- if (v) {
- ret = clk_prepare_enable(clk);
- if (ret)
- goto err_clk;
- } else {
- clk_disable_unprepare(clk);
- }
- }
- return 0;
-
-err_clk:
- for (; i > 0; i--)
- clk_disable_unprepare(this->resources.clock[i - 1]);
- return ret;
-}
-
-int gpmi_enable_clk(struct gpmi_nand_data *this)
-{
- return __gpmi_enable_clk(this, true);
-}
-
-int gpmi_disable_clk(struct gpmi_nand_data *this)
-{
- return __gpmi_enable_clk(this, false);
-}
-
-int gpmi_init(struct gpmi_nand_data *this)
-{
- struct resources *r = &this->resources;
- int ret;
-
- ret = gpmi_enable_clk(this);
- if (ret)
- return ret;
- ret = gpmi_reset_block(r->gpmi_regs, false);
- if (ret)
- goto err_out;
-
- /*
- * Reset BCH here, too. We got failures otherwise :(
- * See later BCH reset for explanation of MX23 and MX28 handling
- */
- ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MXS(this));
- if (ret)
- goto err_out;
-
- /* Choose NAND mode. */
- writel(BM_GPMI_CTRL1_GPMI_MODE, r->gpmi_regs + HW_GPMI_CTRL1_CLR);
-
- /* Set the IRQ polarity. */
- writel(BM_GPMI_CTRL1_ATA_IRQRDY_POLARITY,
- r->gpmi_regs + HW_GPMI_CTRL1_SET);
-
- /* Disable Write-Protection. */
- writel(BM_GPMI_CTRL1_DEV_RESET, r->gpmi_regs + HW_GPMI_CTRL1_SET);
-
- /* Select BCH ECC. */
- writel(BM_GPMI_CTRL1_BCH_MODE, r->gpmi_regs + HW_GPMI_CTRL1_SET);
-
- /*
- * Decouple the chip select from dma channel. We use dma0 for all
- * the chips.
- */
- writel(BM_GPMI_CTRL1_DECOUPLE_CS, r->gpmi_regs + HW_GPMI_CTRL1_SET);
-
- gpmi_disable_clk(this);
- return 0;
-err_out:
- gpmi_disable_clk(this);
- return ret;
-}
-
-/* This function is very useful. It is called only when the bug occur. */
-void gpmi_dump_info(struct gpmi_nand_data *this)
-{
- struct resources *r = &this->resources;
- struct bch_geometry *geo = &this->bch_geometry;
- u32 reg;
- int i;
-
- dev_err(this->dev, "Show GPMI registers :\n");
- for (i = 0; i <= HW_GPMI_DEBUG / 0x10 + 1; i++) {
- reg = readl(r->gpmi_regs + i * 0x10);
- dev_err(this->dev, "offset 0x%.3x : 0x%.8x\n", i * 0x10, reg);
- }
-
- /* start to print out the BCH info */
- dev_err(this->dev, "Show BCH registers :\n");
- for (i = 0; i <= HW_BCH_VERSION / 0x10 + 1; i++) {
- reg = readl(r->bch_regs + i * 0x10);
- dev_err(this->dev, "offset 0x%.3x : 0x%.8x\n", i * 0x10, reg);
- }
- dev_err(this->dev, "BCH Geometry :\n"
- "GF length : %u\n"
- "ECC Strength : %u\n"
- "Page Size in Bytes : %u\n"
- "Metadata Size in Bytes : %u\n"
- "ECC Chunk Size in Bytes: %u\n"
- "ECC Chunk Count : %u\n"
- "Payload Size in Bytes : %u\n"
- "Auxiliary Size in Bytes: %u\n"
- "Auxiliary Status Offset: %u\n"
- "Block Mark Byte Offset : %u\n"
- "Block Mark Bit Offset : %u\n",
- geo->gf_len,
- geo->ecc_strength,
- geo->page_size,
- geo->metadata_size,
- geo->ecc_chunk_size,
- geo->ecc_chunk_count,
- geo->payload_size,
- geo->auxiliary_size,
- geo->auxiliary_status_offset,
- geo->block_mark_byte_offset,
- geo->block_mark_bit_offset);
-}
-
-/* Configures the geometry for BCH. */
-int bch_set_geometry(struct gpmi_nand_data *this)
-{
- struct resources *r = &this->resources;
- struct bch_geometry *bch_geo = &this->bch_geometry;
- unsigned int block_count;
- unsigned int block_size;
- unsigned int metadata_size;
- unsigned int ecc_strength;
- unsigned int page_size;
- unsigned int gf_len;
- int ret;
-
- ret = common_nfc_set_geometry(this);
- if (ret)
- return ret;
-
- block_count = bch_geo->ecc_chunk_count - 1;
- block_size = bch_geo->ecc_chunk_size;
- metadata_size = bch_geo->metadata_size;
- ecc_strength = bch_geo->ecc_strength >> 1;
- page_size = bch_geo->page_size;
- gf_len = bch_geo->gf_len;
-
- ret = gpmi_enable_clk(this);
- if (ret)
- return ret;
-
- /*
- * Due to erratum #2847 of the MX23, the BCH cannot be soft reset on this
- * chip, otherwise it will lock up. So we skip resetting BCH on the MX23.
- * and MX28.
- */
- ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MXS(this));
- if (ret)
- goto err_out;
-
- /* Configure layout 0. */
- writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count)
- | BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size)
- | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this)
- | BF_BCH_FLASH0LAYOUT0_GF(gf_len, this)
- | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this),
- r->bch_regs + HW_BCH_FLASH0LAYOUT0);
-
- writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size)
- | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this)
- | BF_BCH_FLASH0LAYOUT1_GF(gf_len, this)
- | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this),
- r->bch_regs + HW_BCH_FLASH0LAYOUT1);
-
- /* Set *all* chip selects to use layout 0. */
- writel(0, r->bch_regs + HW_BCH_LAYOUTSELECT);
-
- /* Enable interrupts. */
- writel(BM_BCH_CTRL_COMPLETE_IRQ_EN,
- r->bch_regs + HW_BCH_CTRL_SET);
-
- gpmi_disable_clk(this);
- return 0;
-err_out:
- gpmi_disable_clk(this);
- return ret;
-}
-
-/*
- * <1> Firstly, we should know what's the GPMI-clock means.
- * The GPMI-clock is the internal clock in the gpmi nand controller.
- * If you set 100MHz to gpmi nand controller, the GPMI-clock's period
- * is 10ns. Mark the GPMI-clock's period as GPMI-clock-period.
- *
- * <2> Secondly, we should know what's the frequency on the nand chip pins.
- * The frequency on the nand chip pins is derived from the GPMI-clock.
- * We can get it from the following equation:
- *
- * F = G / (DS + DH)
- *
- * F : the frequency on the nand chip pins.
- * G : the GPMI clock, such as 100MHz.
- * DS : GPMI_HW_GPMI_TIMING0:DATA_SETUP
- * DH : GPMI_HW_GPMI_TIMING0:DATA_HOLD
- *
- * <3> Thirdly, when the frequency on the nand chip pins is above 33MHz,
- * the nand EDO(extended Data Out) timing could be applied.
- * The GPMI implements a feedback read strobe to sample the read data.
- * The feedback read strobe can be delayed to support the nand EDO timing
- * where the read strobe may deasserts before the read data is valid, and
- * read data is valid for some time after read strobe.
- *
- * The following figure illustrates some aspects of a NAND Flash read:
- *
- * |<---tREA---->|
- * | |
- * | | |
- * |<--tRP-->| |
- * | | |
- * __ ___|__________________________________
- * RDN \________/ |
- * |
- * /---------\
- * Read Data --------------< >---------
- * \---------/
- * | |
- * |<-D->|
- * FeedbackRDN ________ ____________
- * \___________/
- *
- * D stands for delay, set in the HW_GPMI_CTRL1:RDN_DELAY.
- *
- *
- * <4> Now, we begin to describe how to compute the right RDN_DELAY.
- *
- * 4.1) From the aspect of the nand chip pins:
- * Delay = (tREA + C - tRP) {1}
- *
- * tREA : the maximum read access time.
- * C : a constant to adjust the delay. default is 4000ps.
- * tRP : the read pulse width, which is exactly:
- * tRP = (GPMI-clock-period) * DATA_SETUP
- *
- * 4.2) From the aspect of the GPMI nand controller:
- * Delay = RDN_DELAY * 0.125 * RP {2}
- *
- * RP : the DLL reference period.
- * if (GPMI-clock-period > DLL_THRETHOLD)
- * RP = GPMI-clock-period / 2;
- * else
- * RP = GPMI-clock-period;
- *
- * Set the HW_GPMI_CTRL1:HALF_PERIOD if GPMI-clock-period
- * is greater DLL_THRETHOLD. In other SOCs, the DLL_THRETHOLD
- * is 16000ps, but in mx6q, we use 12000ps.
- *
- * 4.3) since {1} equals {2}, we get:
- *
- * (tREA + 4000 - tRP) * 8
- * RDN_DELAY = ----------------------- {3}
- * RP
- */
-static void gpmi_nfc_compute_timings(struct gpmi_nand_data *this,
- const struct nand_sdr_timings *sdr)
-{
- struct gpmi_nfc_hardware_timing *hw = &this->hw;
- unsigned int dll_threshold_ps = this->devdata->max_chain_delay;
- unsigned int period_ps, reference_period_ps;
- unsigned int data_setup_cycles, data_hold_cycles, addr_setup_cycles;
- unsigned int tRP_ps;
- bool use_half_period;
- int sample_delay_ps, sample_delay_factor;
- u16 busy_timeout_cycles;
- u8 wrn_dly_sel;
-
- if (sdr->tRC_min >= 30000) {
- /* ONFI non-EDO modes [0-3] */
- hw->clk_rate = 22000000;
- wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_4_TO_8NS;
- } else if (sdr->tRC_min >= 25000) {
- /* ONFI EDO mode 4 */
- hw->clk_rate = 80000000;
- wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
- } else {
- /* ONFI EDO mode 5 */
- hw->clk_rate = 100000000;
- wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
- }
-
- /* SDR core timings are given in picoseconds */
- period_ps = div_u64((u64)NSEC_PER_SEC * 1000, hw->clk_rate);
-
- addr_setup_cycles = TO_CYCLES(sdr->tALS_min, period_ps);
- data_setup_cycles = TO_CYCLES(sdr->tDS_min, period_ps);
- data_hold_cycles = TO_CYCLES(sdr->tDH_min, period_ps);
- busy_timeout_cycles = TO_CYCLES(sdr->tWB_max + sdr->tR_max, period_ps);
-
- hw->timing0 = BF_GPMI_TIMING0_ADDRESS_SETUP(addr_setup_cycles) |
- BF_GPMI_TIMING0_DATA_HOLD(data_hold_cycles) |
- BF_GPMI_TIMING0_DATA_SETUP(data_setup_cycles);
- hw->timing1 = BF_GPMI_TIMING1_BUSY_TIMEOUT(busy_timeout_cycles * 4096);
-
- /*
- * Derive NFC ideal delay from {3}:
- *
- * (tREA + 4000 - tRP) * 8
- * RDN_DELAY = -----------------------
- * RP
- */
- if (period_ps > dll_threshold_ps) {
- use_half_period = true;
- reference_period_ps = period_ps / 2;
- } else {
- use_half_period = false;
- reference_period_ps = period_ps;
- }
-
- tRP_ps = data_setup_cycles * period_ps;
- sample_delay_ps = (sdr->tREA_max + 4000 - tRP_ps) * 8;
- if (sample_delay_ps > 0)
- sample_delay_factor = sample_delay_ps / reference_period_ps;
- else
- sample_delay_factor = 0;
-
- hw->ctrl1n = BF_GPMI_CTRL1_WRN_DLY_SEL(wrn_dly_sel);
- if (sample_delay_factor)
- hw->ctrl1n |= BF_GPMI_CTRL1_RDN_DELAY(sample_delay_factor) |
- BM_GPMI_CTRL1_DLL_ENABLE |
- (use_half_period ? BM_GPMI_CTRL1_HALF_PERIOD : 0);
-}
-
-void gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
-{
- struct gpmi_nfc_hardware_timing *hw = &this->hw;
- struct resources *r = &this->resources;
- void __iomem *gpmi_regs = r->gpmi_regs;
- unsigned int dll_wait_time_us;
-
- clk_set_rate(r->clock[0], hw->clk_rate);
-
- writel(hw->timing0, gpmi_regs + HW_GPMI_TIMING0);
- writel(hw->timing1, gpmi_regs + HW_GPMI_TIMING1);
-
- /*
- * Clear several CTRL1 fields, DLL must be disabled when setting
- * RDN_DELAY or HALF_PERIOD.
- */
- writel(BM_GPMI_CTRL1_CLEAR_MASK, gpmi_regs + HW_GPMI_CTRL1_CLR);
- writel(hw->ctrl1n, gpmi_regs + HW_GPMI_CTRL1_SET);
-
- /* Wait 64 clock cycles before using the GPMI after enabling the DLL */
- dll_wait_time_us = USEC_PER_SEC / hw->clk_rate * 64;
- if (!dll_wait_time_us)
- dll_wait_time_us = 1;
-
- /* Wait for the DLL to settle. */
- udelay(dll_wait_time_us);
-}
-
-int gpmi_setup_data_interface(struct nand_chip *chip, int chipnr,
- const struct nand_data_interface *conf)
-{
- struct gpmi_nand_data *this = nand_get_controller_data(chip);
- const struct nand_sdr_timings *sdr;
-
- /* Retrieve required NAND timings */
- sdr = nand_get_sdr_timings(conf);
- if (IS_ERR(sdr))
- return PTR_ERR(sdr);
-
- /* Only MX6 GPMI controller can reach EDO timings */
- if (sdr->tRC_min <= 25000 && !GPMI_IS_MX6(this))
- return -ENOTSUPP;
-
- /* Stop here if this call was just a check */
- if (chipnr < 0)
- return 0;
-
- /* Do the actual derivation of the controller timings */
- gpmi_nfc_compute_timings(this, sdr);
-
- this->hw.must_apply_timings = true;
-
- return 0;
-}
-
-/* Clears a BCH interrupt. */
-void gpmi_clear_bch(struct gpmi_nand_data *this)
-{
- struct resources *r = &this->resources;
- writel(BM_BCH_CTRL_COMPLETE_IRQ, r->bch_regs + HW_BCH_CTRL_CLR);
-}
-
-/* Returns the Ready/Busy status of the given chip. */
-int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip)
-{
- struct resources *r = &this->resources;
- uint32_t mask = 0;
- uint32_t reg = 0;
-
- if (GPMI_IS_MX23(this)) {
- mask = MX23_BM_GPMI_DEBUG_READY0 << chip;
- reg = readl(r->gpmi_regs + HW_GPMI_DEBUG);
- } else if (GPMI_IS_MX28(this) || GPMI_IS_MX6(this)) {
- /*
- * In the imx6, all the ready/busy pins are bound
- * together. So we only need to check chip 0.
- */
- if (GPMI_IS_MX6(this))
- chip = 0;
-
- /* MX28 shares the same R/B register as MX6Q. */
- mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip);
- reg = readl(r->gpmi_regs + HW_GPMI_STAT);
- } else
- dev_err(this->dev, "unknown arch.\n");
- return reg & mask;
-}
-
-int gpmi_send_command(struct gpmi_nand_data *this)
-{
- struct dma_chan *channel = get_dma_chan(this);
- struct dma_async_tx_descriptor *desc;
- struct scatterlist *sgl;
- int chip = this->current_chip;
- int ret;
- u32 pio[3];
-
- /* [1] send out the PIO words */
- pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__WRITE)
- | BM_GPMI_CTRL0_WORD_LENGTH
- | BF_GPMI_CTRL0_CS(chip, this)
- | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
- | BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_CLE)
- | BM_GPMI_CTRL0_ADDRESS_INCREMENT
- | BF_GPMI_CTRL0_XFER_COUNT(this->command_length);
- pio[1] = pio[2] = 0;
- desc = dmaengine_prep_slave_sg(channel,
- (struct scatterlist *)pio,
- ARRAY_SIZE(pio), DMA_TRANS_NONE, 0);
- if (!desc)
- return -EINVAL;
-
- /* [2] send out the COMMAND + ADDRESS string stored in @buffer */
- sgl = &this->cmd_sgl;
-
- sg_init_one(sgl, this->cmd_buffer, this->command_length);
- dma_map_sg(this->dev, sgl, 1, DMA_TO_DEVICE);
- desc = dmaengine_prep_slave_sg(channel,
- sgl, 1, DMA_MEM_TO_DEV,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc)
- return -EINVAL;
-
- /* [3] submit the DMA */
- ret = start_dma_without_bch_irq(this, desc);
-
- dma_unmap_sg(this->dev, sgl, 1, DMA_TO_DEVICE);
-
- return ret;
-}
-
-int gpmi_send_data(struct gpmi_nand_data *this, const void *buf, int len)
-{
- struct dma_async_tx_descriptor *desc;
- struct dma_chan *channel = get_dma_chan(this);
- int chip = this->current_chip;
- int ret;
- uint32_t command_mode;
- uint32_t address;
- u32 pio[2];
-
- /* [1] PIO */
- command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE;
- address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
-
- pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
- | BM_GPMI_CTRL0_WORD_LENGTH
- | BF_GPMI_CTRL0_CS(chip, this)
- | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
- | BF_GPMI_CTRL0_ADDRESS(address)
- | BF_GPMI_CTRL0_XFER_COUNT(len);
- pio[1] = 0;
- desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio,
- ARRAY_SIZE(pio), DMA_TRANS_NONE, 0);
- if (!desc)
- return -EINVAL;
-
- /* [2] send DMA request */
- prepare_data_dma(this, buf, len, DMA_TO_DEVICE);
- desc = dmaengine_prep_slave_sg(channel, &this->data_sgl,
- 1, DMA_MEM_TO_DEV,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc)
- return -EINVAL;
-
- /* [3] submit the DMA */
- ret = start_dma_without_bch_irq(this, desc);
-
- dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_TO_DEVICE);
-
- return ret;
-}
-
-int gpmi_read_data(struct gpmi_nand_data *this, void *buf, int len)
-{
- struct dma_async_tx_descriptor *desc;
- struct dma_chan *channel = get_dma_chan(this);
- int chip = this->current_chip;
- int ret;
- u32 pio[2];
- bool direct;
-
- /* [1] : send PIO */
- pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__READ)
- | BM_GPMI_CTRL0_WORD_LENGTH
- | BF_GPMI_CTRL0_CS(chip, this)
- | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
- | BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_DATA)
- | BF_GPMI_CTRL0_XFER_COUNT(len);
- pio[1] = 0;
- desc = dmaengine_prep_slave_sg(channel,
- (struct scatterlist *)pio,
- ARRAY_SIZE(pio), DMA_TRANS_NONE, 0);
- if (!desc)
- return -EINVAL;
-
- /* [2] : send DMA request */
- direct = prepare_data_dma(this, buf, len, DMA_FROM_DEVICE);
- desc = dmaengine_prep_slave_sg(channel, &this->data_sgl,
- 1, DMA_DEV_TO_MEM,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc)
- return -EINVAL;
-
- /* [3] : submit the DMA */
-
- ret = start_dma_without_bch_irq(this, desc);
-
- dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_FROM_DEVICE);
- if (!direct)
- memcpy(buf, this->data_buffer_dma, len);
-
- return ret;
-}
-
-int gpmi_send_page(struct gpmi_nand_data *this,
- dma_addr_t payload, dma_addr_t auxiliary)
-{
- struct bch_geometry *geo = &this->bch_geometry;
- uint32_t command_mode;
- uint32_t address;
- uint32_t ecc_command;
- uint32_t buffer_mask;
- struct dma_async_tx_descriptor *desc;
- struct dma_chan *channel = get_dma_chan(this);
- int chip = this->current_chip;
- u32 pio[6];
-
- /* A DMA descriptor that does an ECC page read. */
- command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE;
- address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
- ecc_command = BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE;
- buffer_mask = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE |
- BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY;
-
- pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
- | BM_GPMI_CTRL0_WORD_LENGTH
- | BF_GPMI_CTRL0_CS(chip, this)
- | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
- | BF_GPMI_CTRL0_ADDRESS(address)
- | BF_GPMI_CTRL0_XFER_COUNT(0);
- pio[1] = 0;
- pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC
- | BF_GPMI_ECCCTRL_ECC_CMD(ecc_command)
- | BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask);
- pio[3] = geo->page_size;
- pio[4] = payload;
- pio[5] = auxiliary;
-
- desc = dmaengine_prep_slave_sg(channel,
- (struct scatterlist *)pio,
- ARRAY_SIZE(pio), DMA_TRANS_NONE,
- DMA_CTRL_ACK);
- if (!desc)
- return -EINVAL;
-
- return start_dma_with_bch_irq(this, desc);
-}
-
-int gpmi_read_page(struct gpmi_nand_data *this,
- dma_addr_t payload, dma_addr_t auxiliary)
-{
- struct bch_geometry *geo = &this->bch_geometry;
- uint32_t command_mode;
- uint32_t address;
- uint32_t ecc_command;
- uint32_t buffer_mask;
- struct dma_async_tx_descriptor *desc;
- struct dma_chan *channel = get_dma_chan(this);
- int chip = this->current_chip;
- u32 pio[6];
-
- /* [1] Wait for the chip to report ready. */
- command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY;
- address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
-
- pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
- | BM_GPMI_CTRL0_WORD_LENGTH
- | BF_GPMI_CTRL0_CS(chip, this)
- | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
- | BF_GPMI_CTRL0_ADDRESS(address)
- | BF_GPMI_CTRL0_XFER_COUNT(0);
- pio[1] = 0;
- desc = dmaengine_prep_slave_sg(channel,
- (struct scatterlist *)pio, 2,
- DMA_TRANS_NONE, 0);
- if (!desc)
- return -EINVAL;
-
- /* [2] Enable the BCH block and read. */
- command_mode = BV_GPMI_CTRL0_COMMAND_MODE__READ;
- address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
- ecc_command = BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE;
- buffer_mask = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE
- | BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY;
-
- pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
- | BM_GPMI_CTRL0_WORD_LENGTH
- | BF_GPMI_CTRL0_CS(chip, this)
- | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
- | BF_GPMI_CTRL0_ADDRESS(address)
- | BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
-
- pio[1] = 0;
- pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC
- | BF_GPMI_ECCCTRL_ECC_CMD(ecc_command)
- | BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask);
- pio[3] = geo->page_size;
- pio[4] = payload;
- pio[5] = auxiliary;
- desc = dmaengine_prep_slave_sg(channel,
- (struct scatterlist *)pio,
- ARRAY_SIZE(pio), DMA_TRANS_NONE,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc)
- return -EINVAL;
-
- /* [3] Disable the BCH block */
- command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY;
- address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
-
- pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
- | BM_GPMI_CTRL0_WORD_LENGTH
- | BF_GPMI_CTRL0_CS(chip, this)
- | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
- | BF_GPMI_CTRL0_ADDRESS(address)
- | BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
- pio[1] = 0;
- pio[2] = 0; /* clear GPMI_HW_GPMI_ECCCTRL, disable the BCH. */
- desc = dmaengine_prep_slave_sg(channel,
- (struct scatterlist *)pio, 3,
- DMA_TRANS_NONE,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
- if (!desc)
- return -EINVAL;
-
- /* [4] submit the DMA */
- return start_dma_with_bch_irq(this, desc);
-}
-
-/**
- * gpmi_copy_bits - copy bits from one memory region to another
- * @dst: destination buffer
- * @dst_bit_off: bit offset we're starting to write at
- * @src: source buffer
- * @src_bit_off: bit offset we're starting to read from
- * @nbits: number of bits to copy
- *
- * This functions copies bits from one memory region to another, and is used by
- * the GPMI driver to copy ECC sections which are not guaranteed to be byte
- * aligned.
- *
- * src and dst should not overlap.
- *
- */
-void gpmi_copy_bits(u8 *dst, size_t dst_bit_off,
- const u8 *src, size_t src_bit_off,
- size_t nbits)
-{
- size_t i;
- size_t nbytes;
- u32 src_buffer = 0;
- size_t bits_in_src_buffer = 0;
-
- if (!nbits)
- return;
-
- /*
- * Move src and dst pointers to the closest byte pointer and store bit
- * offsets within a byte.
- */
- src += src_bit_off / 8;
- src_bit_off %= 8;
-
- dst += dst_bit_off / 8;
- dst_bit_off %= 8;
-
- /*
- * Initialize the src_buffer value with bits available in the first
- * byte of data so that we end up with a byte aligned src pointer.
- */
- if (src_bit_off) {
- src_buffer = src[0] >> src_bit_off;
- if (nbits >= (8 - src_bit_off)) {
- bits_in_src_buffer += 8 - src_bit_off;
- } else {
- src_buffer &= GENMASK(nbits - 1, 0);
- bits_in_src_buffer += nbits;
- }
- nbits -= bits_in_src_buffer;
- src++;
- }
-
- /* Calculate the number of bytes that can be copied from src to dst. */
- nbytes = nbits / 8;
-
- /* Try to align dst to a byte boundary. */
- if (dst_bit_off) {
- if (bits_in_src_buffer < (8 - dst_bit_off) && nbytes) {
- src_buffer |= src[0] << bits_in_src_buffer;
- bits_in_src_buffer += 8;
- src++;
- nbytes--;
- }
-
- if (bits_in_src_buffer >= (8 - dst_bit_off)) {
- dst[0] &= GENMASK(dst_bit_off - 1, 0);
- dst[0] |= src_buffer << dst_bit_off;
- src_buffer >>= (8 - dst_bit_off);
- bits_in_src_buffer -= (8 - dst_bit_off);
- dst_bit_off = 0;
- dst++;
- if (bits_in_src_buffer > 7) {
- bits_in_src_buffer -= 8;
- dst[0] = src_buffer;
- dst++;
- src_buffer >>= 8;
- }
- }
- }
-
- if (!bits_in_src_buffer && !dst_bit_off) {
- /*
- * Both src and dst pointers are byte aligned, thus we can
- * just use the optimized memcpy function.
- */
- if (nbytes)
- memcpy(dst, src, nbytes);
- } else {
- /*
- * src buffer is not byte aligned, hence we have to copy each
- * src byte to the src_buffer variable before extracting a byte
- * to store in dst.
- */
- for (i = 0; i < nbytes; i++) {
- src_buffer |= src[i] << bits_in_src_buffer;
- dst[i] = src_buffer;
- src_buffer >>= 8;
- }
- }
- /* Update dst and src pointers */
- dst += nbytes;
- src += nbytes;
-
- /*
- * nbits is the number of remaining bits. It should not exceed 8 as
- * we've already copied as much bytes as possible.
- */
- nbits %= 8;
-
- /*
- * If there's no more bits to copy to the destination and src buffer
- * was already byte aligned, then we're done.
- */
- if (!nbits && !bits_in_src_buffer)
- return;
-
- /* Copy the remaining bits to src_buffer */
- if (nbits)
- src_buffer |= (*src & GENMASK(nbits - 1, 0)) <<
- bits_in_src_buffer;
- bits_in_src_buffer += nbits;
-
- /*
- * In case there were not enough bits to get a byte aligned dst buffer
- * prepare the src_buffer variable to match the dst organization (shift
- * src_buffer by dst_bit_off and retrieve the least significant bits
- * from dst).
- */
- if (dst_bit_off)
- src_buffer = (src_buffer << dst_bit_off) |
- (*dst & GENMASK(dst_bit_off - 1, 0));
- bits_in_src_buffer += dst_bit_off;
-
- /*
- * Keep most significant bits from dst if we end up with an unaligned
- * number of bits.
- */
- nbytes = bits_in_src_buffer / 8;
- if (bits_in_src_buffer % 8) {
- src_buffer |= (dst[nbytes] &
- GENMASK(7, bits_in_src_buffer % 8)) <<
- (nbytes * 8);
- nbytes++;
- }
-
- /* Copy the remaining bytes to dst */
- for (i = 0; i < nbytes; i++) {
- dst[i] = src_buffer;
- src_buffer >>= 8;
- }
-}
diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
index 40df20d1adf5..53e63eeafcf4 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
@@ -6,6 +6,7 @@
* Copyright (C) 2008 Embedded Alley Solutions, Inc.
*/
#include <linux/clk.h>
+#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/sched/task_stack.h>
#include <linux/interrupt.h>
@@ -14,6 +15,7 @@
#include <linux/of.h>
#include <linux/of_device.h>
#include "gpmi-nand.h"
+#include "gpmi-regs.h"
#include "bch-regs.h"
/* Resource names for the GPMI NAND driver. */
@@ -21,149 +23,223 @@
#define GPMI_NAND_BCH_REGS_ADDR_RES_NAME "bch"
#define GPMI_NAND_BCH_INTERRUPT_RES_NAME "bch"
-/* add our owner bbt descriptor */
-static uint8_t scan_ff_pattern[] = { 0xff };
-static struct nand_bbt_descr gpmi_bbt_descr = {
- .options = 0,
- .offs = 0,
- .len = 1,
- .pattern = scan_ff_pattern
-};
+/* Converts time to clock cycles */
+#define TO_CYCLES(duration, period) DIV_ROUND_UP_ULL(duration, period)
+#define MXS_SET_ADDR 0x4
+#define MXS_CLR_ADDR 0x8
/*
- * We may change the layout if we can get the ECC info from the datasheet,
- * else we will use all the (page + OOB).
+ * Clear the bit and poll it cleared. This is usually called with
+ * a reset address and mask being either SFTRST(bit 31) or CLKGATE
+ * (bit 30).
*/
-static int gpmi_ooblayout_ecc(struct mtd_info *mtd, int section,
- struct mtd_oob_region *oobregion)
+static int clear_poll_bit(void __iomem *addr, u32 mask)
{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct gpmi_nand_data *this = nand_get_controller_data(chip);
- struct bch_geometry *geo = &this->bch_geometry;
+ int timeout = 0x400;
- if (section)
- return -ERANGE;
+ /* clear the bit */
+ writel(mask, addr + MXS_CLR_ADDR);
- oobregion->offset = 0;
- oobregion->length = geo->page_size - mtd->writesize;
+ /*
+ * SFTRST needs 3 GPMI clocks to settle, the reference manual
+ * recommends to wait 1us.
+ */
+ udelay(1);
+
+ /* poll the bit becoming clear */
+ while ((readl(addr) & mask) && --timeout)
+ /* nothing */;
+
+ return !timeout;
+}
+
+#define MODULE_CLKGATE (1 << 30)
+#define MODULE_SFTRST (1 << 31)
+/*
+ * The current mxs_reset_block() will do two things:
+ * [1] enable the module.
+ * [2] reset the module.
+ *
+ * In most of the cases, it's ok.
+ * But in MX23, there is a hardware bug in the BCH block (see erratum #2847).
+ * If you try to soft reset the BCH block, it becomes unusable until
+ * the next hard reset. This case occurs in the NAND boot mode. When the board
+ * boots by NAND, the ROM of the chip will initialize the BCH blocks itself.
+ * So If the driver tries to reset the BCH again, the BCH will not work anymore.
+ * You will see a DMA timeout in this case. The bug has been fixed
+ * in the following chips, such as MX28.
+ *
+ * To avoid this bug, just add a new parameter `just_enable` for
+ * the mxs_reset_block(), and rewrite it here.
+ */
+static int gpmi_reset_block(void __iomem *reset_addr, bool just_enable)
+{
+ int ret;
+ int timeout = 0x400;
+
+ /* clear and poll SFTRST */
+ ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
+ if (unlikely(ret))
+ goto error;
+
+ /* clear CLKGATE */
+ writel(MODULE_CLKGATE, reset_addr + MXS_CLR_ADDR);
+
+ if (!just_enable) {
+ /* set SFTRST to reset the block */
+ writel(MODULE_SFTRST, reset_addr + MXS_SET_ADDR);
+ udelay(1);
+
+ /* poll CLKGATE becoming set */
+ while ((!(readl(reset_addr) & MODULE_CLKGATE)) && --timeout)
+ /* nothing */;
+ if (unlikely(!timeout))
+ goto error;
+ }
+
+ /* clear and poll SFTRST */
+ ret = clear_poll_bit(reset_addr, MODULE_SFTRST);
+ if (unlikely(ret))
+ goto error;
+
+ /* clear and poll CLKGATE */
+ ret = clear_poll_bit(reset_addr, MODULE_CLKGATE);
+ if (unlikely(ret))
+ goto error;
return 0;
+
+error:
+ pr_err("%s(%p): module reset timeout\n", __func__, reset_addr);
+ return -ETIMEDOUT;
}
-static int gpmi_ooblayout_free(struct mtd_info *mtd, int section,
- struct mtd_oob_region *oobregion)
+static int __gpmi_enable_clk(struct gpmi_nand_data *this, bool v)
{
- struct nand_chip *chip = mtd_to_nand(mtd);
- struct gpmi_nand_data *this = nand_get_controller_data(chip);
- struct bch_geometry *geo = &this->bch_geometry;
+ struct clk *clk;
+ int ret;
+ int i;
- if (section)
- return -ERANGE;
+ for (i = 0; i < GPMI_CLK_MAX; i++) {
+ clk = this->resources.clock[i];
+ if (!clk)
+ break;
- /* The available oob size we have. */
- if (geo->page_size < mtd->writesize + mtd->oobsize) {
- oobregion->offset = geo->page_size - mtd->writesize;
- oobregion->length = mtd->oobsize - oobregion->offset;
+ if (v) {
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ goto err_clk;
+ } else {
+ clk_disable_unprepare(clk);
+ }
}
-
return 0;
+
+err_clk:
+ for (; i > 0; i--)
+ clk_disable_unprepare(this->resources.clock[i - 1]);
+ return ret;
}
-static const char * const gpmi_clks_for_mx2x[] = {
- "gpmi_io",
-};
+static int gpmi_enable_clk(struct gpmi_nand_data *this)
+{
+ return __gpmi_enable_clk(this, true);
+}
-static const struct mtd_ooblayout_ops gpmi_ooblayout_ops = {
- .ecc = gpmi_ooblayout_ecc,
- .free = gpmi_ooblayout_free,
-};
+static int gpmi_disable_clk(struct gpmi_nand_data *this)
+{
+ return __gpmi_enable_clk(this, false);
+}
-static const struct gpmi_devdata gpmi_devdata_imx23 = {
- .type = IS_MX23,
- .bch_max_ecc_strength = 20,
- .max_chain_delay = 16000,
- .clks = gpmi_clks_for_mx2x,
- .clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
-};
+static int gpmi_init(struct gpmi_nand_data *this)
+{
+ struct resources *r = &this->resources;
+ int ret;
-static const struct gpmi_devdata gpmi_devdata_imx28 = {
- .type = IS_MX28,
- .bch_max_ecc_strength = 20,
- .max_chain_delay = 16000,
- .clks = gpmi_clks_for_mx2x,
- .clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
-};
+ ret = gpmi_enable_clk(this);
+ if (ret)
+ return ret;
+ ret = gpmi_reset_block(r->gpmi_regs, false);
+ if (ret)
+ goto err_out;
-static const char * const gpmi_clks_for_mx6[] = {
- "gpmi_io", "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch",
-};
+ /*
+ * Reset BCH here, too. We got failures otherwise :(
+ * See later BCH reset for explanation of MX23 and MX28 handling
+ */
+ ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MXS(this));
+ if (ret)
+ goto err_out;
-static const struct gpmi_devdata gpmi_devdata_imx6q = {
- .type = IS_MX6Q,
- .bch_max_ecc_strength = 40,
- .max_chain_delay = 12000,
- .clks = gpmi_clks_for_mx6,
- .clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
-};
+ /* Choose NAND mode. */
+ writel(BM_GPMI_CTRL1_GPMI_MODE, r->gpmi_regs + HW_GPMI_CTRL1_CLR);
-static const struct gpmi_devdata gpmi_devdata_imx6sx = {
- .type = IS_MX6SX,
- .bch_max_ecc_strength = 62,
- .max_chain_delay = 12000,
- .clks = gpmi_clks_for_mx6,
- .clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
-};
+ /* Set the IRQ polarity. */
+ writel(BM_GPMI_CTRL1_ATA_IRQRDY_POLARITY,
+ r->gpmi_regs + HW_GPMI_CTRL1_SET);
-static const char * const gpmi_clks_for_mx7d[] = {
- "gpmi_io", "gpmi_bch_apb",
-};
+ /* Disable Write-Protection. */
+ writel(BM_GPMI_CTRL1_DEV_RESET, r->gpmi_regs + HW_GPMI_CTRL1_SET);
-static const struct gpmi_devdata gpmi_devdata_imx7d = {
- .type = IS_MX7D,
- .bch_max_ecc_strength = 62,
- .max_chain_delay = 12000,
- .clks = gpmi_clks_for_mx7d,
- .clks_count = ARRAY_SIZE(gpmi_clks_for_mx7d),
-};
+ /* Select BCH ECC. */
+ writel(BM_GPMI_CTRL1_BCH_MODE, r->gpmi_regs + HW_GPMI_CTRL1_SET);
-static irqreturn_t bch_irq(int irq, void *cookie)
-{
- struct gpmi_nand_data *this = cookie;
+ /*
+ * Decouple the chip select from dma channel. We use dma0 for all
+ * the chips.
+ */
+ writel(BM_GPMI_CTRL1_DECOUPLE_CS, r->gpmi_regs + HW_GPMI_CTRL1_SET);
- gpmi_clear_bch(this);
- complete(&this->bch_done);
- return IRQ_HANDLED;
+ gpmi_disable_clk(this);
+ return 0;
+err_out:
+ gpmi_disable_clk(this);
+ return ret;
}
-/*
- * Calculate the ECC strength by hand:
- * E : The ECC strength.
- * G : the length of Galois Field.
- * N : The chunk count of per page.
- * O : the oobsize of the NAND chip.
- * M : the metasize of per page.
- *
- * The formula is :
- * E * G * N
- * ------------ <= (O - M)
- * 8
- *
- * So, we get E by:
- * (O - M) * 8
- * E <= -------------
- * G * N
- */
-static inline int get_ecc_strength(struct gpmi_nand_data *this)
+/* This function is very useful. It is called only when the bug occur. */
+static void gpmi_dump_info(struct gpmi_nand_data *this)
{
+ struct resources *r = &this->resources;
struct bch_geometry *geo = &this->bch_geometry;
- struct mtd_info *mtd = nand_to_mtd(&this->nand);
- int ecc_strength;
+ u32 reg;
+ int i;
- ecc_strength = ((mtd->oobsize - geo->metadata_size) * 8)
- / (geo->gf_len * geo->ecc_chunk_count);
+ dev_err(this->dev, "Show GPMI registers :\n");
+ for (i = 0; i <= HW_GPMI_DEBUG / 0x10 + 1; i++) {
+ reg = readl(r->gpmi_regs + i * 0x10);
+ dev_err(this->dev, "offset 0x%.3x : 0x%.8x\n", i * 0x10, reg);
+ }
- /* We need the minor even number. */
- return round_down(ecc_strength, 2);
+ /* start to print out the BCH info */
+ dev_err(this->dev, "Show BCH registers :\n");
+ for (i = 0; i <= HW_BCH_VERSION / 0x10 + 1; i++) {
+ reg = readl(r->bch_regs + i * 0x10);
+ dev_err(this->dev, "offset 0x%.3x : 0x%.8x\n", i * 0x10, reg);
+ }
+ dev_err(this->dev, "BCH Geometry :\n"
+ "GF length : %u\n"
+ "ECC Strength : %u\n"
+ "Page Size in Bytes : %u\n"
+ "Metadata Size in Bytes : %u\n"
+ "ECC Chunk Size in Bytes: %u\n"
+ "ECC Chunk Count : %u\n"
+ "Payload Size in Bytes : %u\n"
+ "Auxiliary Size in Bytes: %u\n"
+ "Auxiliary Status Offset: %u\n"
+ "Block Mark Byte Offset : %u\n"
+ "Block Mark Bit Offset : %u\n",
+ geo->gf_len,
+ geo->ecc_strength,
+ geo->page_size,
+ geo->metadata_size,
+ geo->ecc_chunk_size,
+ geo->ecc_chunk_count,
+ geo->payload_size,
+ geo->auxiliary_size,
+ geo->auxiliary_status_offset,
+ geo->block_mark_byte_offset,
+ geo->block_mark_bit_offset);
}
static inline bool gpmi_check_ecc(struct gpmi_nand_data *this)
@@ -296,6 +372,37 @@ static int set_geometry_by_ecc_info(struct gpmi_nand_data *this,
return 0;
}
+/*
+ * Calculate the ECC strength by hand:
+ * E : The ECC strength.
+ * G : the length of Galois Field.
+ * N : The chunk count of per page.
+ * O : the oobsize of the NAND chip.
+ * M : the metasize of per page.
+ *
+ * The formula is :
+ * E * G * N
+ * ------------ <= (O - M)
+ * 8
+ *
+ * So, we get E by:
+ * (O - M) * 8
+ * E <= -------------
+ * G * N
+ */
+static inline int get_ecc_strength(struct gpmi_nand_data *this)
+{
+ struct bch_geometry *geo = &this->bch_geometry;
+ struct mtd_info *mtd = nand_to_mtd(&this->nand);
+ int ecc_strength;
+
+ ecc_strength = ((mtd->oobsize - geo->metadata_size) * 8)
+ / (geo->gf_len * geo->ecc_chunk_count);
+
+ /* We need the minor even number. */
+ return round_down(ecc_strength, 2);
+}
+
static int legacy_set_geometry(struct gpmi_nand_data *this)
{
struct bch_geometry *geo = &this->bch_geometry;
@@ -408,7 +515,7 @@ static int legacy_set_geometry(struct gpmi_nand_data *this)
return 0;
}
-int common_nfc_set_geometry(struct gpmi_nand_data *this)
+static int common_nfc_set_geometry(struct gpmi_nand_data *this)
{
struct nand_chip *chip = &this->nand;
@@ -430,84 +537,360 @@ int common_nfc_set_geometry(struct gpmi_nand_data *this)
return 0;
}
-struct dma_chan *get_dma_chan(struct gpmi_nand_data *this)
-{
- /* We use the DMA channel 0 to access all the nand chips. */
- return this->dma_chans[0];
-}
-
-/* Can we use the upper's buffer directly for DMA? */
-bool prepare_data_dma(struct gpmi_nand_data *this, const void *buf, int len,
- enum dma_data_direction dr)
+/* Configures the geometry for BCH. */
+static int bch_set_geometry(struct gpmi_nand_data *this)
{
- struct scatterlist *sgl = &this->data_sgl;
+ struct resources *r = &this->resources;
+ struct bch_geometry *bch_geo = &this->bch_geometry;
+ unsigned int block_count;
+ unsigned int block_size;
+ unsigned int metadata_size;
+ unsigned int ecc_strength;
+ unsigned int page_size;
+ unsigned int gf_len;
int ret;
- /* first try to map the upper buffer directly */
- if (virt_addr_valid(buf) && !object_is_on_stack(buf)) {
- sg_init_one(sgl, buf, len);
- ret = dma_map_sg(this->dev, sgl, 1, dr);
- if (ret == 0)
- goto map_fail;
-
- return true;
- }
-
-map_fail:
- /* We have to use our own DMA buffer. */
- sg_init_one(sgl, this->data_buffer_dma, len);
-
- if (dr == DMA_TO_DEVICE)
- memcpy(this->data_buffer_dma, buf, len);
+ ret = common_nfc_set_geometry(this);
+ if (ret)
+ return ret;
- dma_map_sg(this->dev, sgl, 1, dr);
+ block_count = bch_geo->ecc_chunk_count - 1;
+ block_size = bch_geo->ecc_chunk_size;
+ metadata_size = bch_geo->metadata_size;
+ ecc_strength = bch_geo->ecc_strength >> 1;
+ page_size = bch_geo->page_size;
+ gf_len = bch_geo->gf_len;
- return false;
-}
+ ret = gpmi_enable_clk(this);
+ if (ret)
+ return ret;
-/* This will be called after the DMA operation is finished. */
-static void dma_irq_callback(void *param)
-{
- struct gpmi_nand_data *this = param;
- struct completion *dma_c = &this->dma_done;
+ /*
+ * Due to erratum #2847 of the MX23, the BCH cannot be soft reset on this
+ * chip, otherwise it will lock up. So we skip resetting BCH on the MX23.
+ * and MX28.
+ */
+ ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MXS(this));
+ if (ret)
+ goto err_out;
- complete(dma_c);
-}
+ /* Configure layout 0. */
+ writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count)
+ | BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size)
+ | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this)
+ | BF_BCH_FLASH0LAYOUT0_GF(gf_len, this)
+ | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this),
+ r->bch_regs + HW_BCH_FLASH0LAYOUT0);
-int start_dma_without_bch_irq(struct gpmi_nand_data *this,
- struct dma_async_tx_descriptor *desc)
-{
- struct completion *dma_c = &this->dma_done;
- unsigned long timeout;
+ writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size)
+ | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this)
+ | BF_BCH_FLASH0LAYOUT1_GF(gf_len, this)
+ | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this),
+ r->bch_regs + HW_BCH_FLASH0LAYOUT1);
- init_completion(dma_c);
+ /* Set *all* chip selects to use layout 0. */
+ writel(0, r->bch_regs + HW_BCH_LAYOUTSELECT);
- desc->callback = dma_irq_callback;
- desc->callback_param = this;
- dmaengine_submit(desc);
- dma_async_issue_pending(get_dma_chan(this));
+ /* Enable interrupts. */
+ writel(BM_BCH_CTRL_COMPLETE_IRQ_EN,
+ r->bch_regs + HW_BCH_CTRL_SET);
- /* Wait for the interrupt from the DMA block. */
- timeout = wait_for_completion_timeout(dma_c, msecs_to_jiffies(1000));
- if (!timeout) {
- dev_err(this->dev, "DMA timeout, last DMA\n");
- gpmi_dump_info(this);
- return -ETIMEDOUT;
- }
+ gpmi_disable_clk(this);
return 0;
+err_out:
+ gpmi_disable_clk(this);
+ return ret;
}
/*
- * This function is used in BCH reading or BCH writing pages.
- * It will wait for the BCH interrupt as long as ONE second.
- * Actually, we must wait for two interrupts :
- * [1] firstly the DMA interrupt and
- * [2] secondly the BCH interrupt.
- */
-int start_dma_with_bch_irq(struct gpmi_nand_data *this,
- struct dma_async_tx_descriptor *desc)
-{
- struct completion *bch_c = &this->bch_done;
+ * <1> Firstly, we should know what's the GPMI-clock means.
+ * The GPMI-clock is the internal clock in the gpmi nand controller.
+ * If you set 100MHz to gpmi nand controller, the GPMI-clock's period
+ * is 10ns. Mark the GPMI-clock's period as GPMI-clock-period.
+ *
+ * <2> Secondly, we should know what's the frequency on the nand chip pins.
+ * The frequency on the nand chip pins is derived from the GPMI-clock.
+ * We can get it from the following equation:
+ *
+ * F = G / (DS + DH)
+ *
+ * F : the frequency on the nand chip pins.
+ * G : the GPMI clock, such as 100MHz.
+ * DS : GPMI_HW_GPMI_TIMING0:DATA_SETUP
+ * DH : GPMI_HW_GPMI_TIMING0:DATA_HOLD
+ *
+ * <3> Thirdly, when the frequency on the nand chip pins is above 33MHz,
+ * the nand EDO(extended Data Out) timing could be applied.
+ * The GPMI implements a feedback read strobe to sample the read data.
+ * The feedback read strobe can be delayed to support the nand EDO timing
+ * where the read strobe may deasserts before the read data is valid, and
+ * read data is valid for some time after read strobe.
+ *
+ * The following figure illustrates some aspects of a NAND Flash read:
+ *
+ * |<---tREA---->|
+ * | |
+ * | | |
+ * |<--tRP-->| |
+ * | | |
+ * __ ___|__________________________________
+ * RDN \________/ |
+ * |
+ * /---------\
+ * Read Data --------------< >---------
+ * \---------/
+ * | |
+ * |<-D->|
+ * FeedbackRDN ________ ____________
+ * \___________/
+ *
+ * D stands for delay, set in the HW_GPMI_CTRL1:RDN_DELAY.
+ *
+ *
+ * <4> Now, we begin to describe how to compute the right RDN_DELAY.
+ *
+ * 4.1) From the aspect of the nand chip pins:
+ * Delay = (tREA + C - tRP) {1}
+ *
+ * tREA : the maximum read access time.
+ * C : a constant to adjust the delay. default is 4000ps.
+ * tRP : the read pulse width, which is exactly:
+ * tRP = (GPMI-clock-period) * DATA_SETUP
+ *
+ * 4.2) From the aspect of the GPMI nand controller:
+ * Delay = RDN_DELAY * 0.125 * RP {2}
+ *
+ * RP : the DLL reference period.
+ * if (GPMI-clock-period > DLL_THRETHOLD)
+ * RP = GPMI-clock-period / 2;
+ * else
+ * RP = GPMI-clock-period;
+ *
+ * Set the HW_GPMI_CTRL1:HALF_PERIOD if GPMI-clock-period
+ * is greater DLL_THRETHOLD. In other SOCs, the DLL_THRETHOLD
+ * is 16000ps, but in mx6q, we use 12000ps.
+ *
+ * 4.3) since {1} equals {2}, we get:
+ *
+ * (tREA + 4000 - tRP) * 8
+ * RDN_DELAY = ----------------------- {3}
+ * RP
+ */
+static void gpmi_nfc_compute_timings(struct gpmi_nand_data *this,
+ const struct nand_sdr_timings *sdr)
+{
+ struct gpmi_nfc_hardware_timing *hw = &this->hw;
+ unsigned int dll_threshold_ps = this->devdata->max_chain_delay;
+ unsigned int period_ps, reference_period_ps;
+ unsigned int data_setup_cycles, data_hold_cycles, addr_setup_cycles;
+ unsigned int tRP_ps;
+ bool use_half_period;
+ int sample_delay_ps, sample_delay_factor;
+ u16 busy_timeout_cycles;
+ u8 wrn_dly_sel;
+
+ if (sdr->tRC_min >= 30000) {
+ /* ONFI non-EDO modes [0-3] */
+ hw->clk_rate = 22000000;
+ wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_4_TO_8NS;
+ } else if (sdr->tRC_min >= 25000) {
+ /* ONFI EDO mode 4 */
+ hw->clk_rate = 80000000;
+ wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
+ } else {
+ /* ONFI EDO mode 5 */
+ hw->clk_rate = 100000000;
+ wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
+ }
+
+ /* SDR core timings are given in picoseconds */
+ period_ps = div_u64((u64)NSEC_PER_SEC * 1000, hw->clk_rate);
+
+ addr_setup_cycles = TO_CYCLES(sdr->tALS_min, period_ps);
+ data_setup_cycles = TO_CYCLES(sdr->tDS_min, period_ps);
+ data_hold_cycles = TO_CYCLES(sdr->tDH_min, period_ps);
+ busy_timeout_cycles = TO_CYCLES(sdr->tWB_max + sdr->tR_max, period_ps);
+
+ hw->timing0 = BF_GPMI_TIMING0_ADDRESS_SETUP(addr_setup_cycles) |
+ BF_GPMI_TIMING0_DATA_HOLD(data_hold_cycles) |
+ BF_GPMI_TIMING0_DATA_SETUP(data_setup_cycles);
+ hw->timing1 = BF_GPMI_TIMING1_BUSY_TIMEOUT(busy_timeout_cycles * 4096);
+
+ /*
+ * Derive NFC ideal delay from {3}:
+ *
+ * (tREA + 4000 - tRP) * 8
+ * RDN_DELAY = -----------------------
+ * RP
+ */
+ if (period_ps > dll_threshold_ps) {
+ use_half_period = true;
+ reference_period_ps = period_ps / 2;
+ } else {
+ use_half_period = false;
+ reference_period_ps = period_ps;
+ }
+
+ tRP_ps = data_setup_cycles * period_ps;
+ sample_delay_ps = (sdr->tREA_max + 4000 - tRP_ps) * 8;
+ if (sample_delay_ps > 0)
+ sample_delay_factor = sample_delay_ps / reference_period_ps;
+ else
+ sample_delay_factor = 0;
+
+ hw->ctrl1n = BF_GPMI_CTRL1_WRN_DLY_SEL(wrn_dly_sel);
+ if (sample_delay_factor)
+ hw->ctrl1n |= BF_GPMI_CTRL1_RDN_DELAY(sample_delay_factor) |
+ BM_GPMI_CTRL1_DLL_ENABLE |
+ (use_half_period ? BM_GPMI_CTRL1_HALF_PERIOD : 0);
+}
+
+static void gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
+{
+ struct gpmi_nfc_hardware_timing *hw = &this->hw;
+ struct resources *r = &this->resources;
+ void __iomem *gpmi_regs = r->gpmi_regs;
+ unsigned int dll_wait_time_us;
+
+ clk_set_rate(r->clock[0], hw->clk_rate);
+
+ writel(hw->timing0, gpmi_regs + HW_GPMI_TIMING0);
+ writel(hw->timing1, gpmi_regs + HW_GPMI_TIMING1);
+
+ /*
+ * Clear several CTRL1 fields, DLL must be disabled when setting
+ * RDN_DELAY or HALF_PERIOD.
+ */
+ writel(BM_GPMI_CTRL1_CLEAR_MASK, gpmi_regs + HW_GPMI_CTRL1_CLR);
+ writel(hw->ctrl1n, gpmi_regs + HW_GPMI_CTRL1_SET);
+
+ /* Wait 64 clock cycles before using the GPMI after enabling the DLL */
+ dll_wait_time_us = USEC_PER_SEC / hw->clk_rate * 64;
+ if (!dll_wait_time_us)
+ dll_wait_time_us = 1;
+
+ /* Wait for the DLL to settle. */
+ udelay(dll_wait_time_us);
+}
+
+static int gpmi_setup_data_interface(struct nand_chip *chip, int chipnr,
+ const struct nand_data_interface *conf)
+{
+ struct gpmi_nand_data *this = nand_get_controller_data(chip);
+ const struct nand_sdr_timings *sdr;
+
+ /* Retrieve required NAND timings */
+ sdr = nand_get_sdr_timings(conf);
+ if (IS_ERR(sdr))
+ return PTR_ERR(sdr);
+
+ /* Only MX6 GPMI controller can reach EDO timings */
+ if (sdr->tRC_min <= 25000 && !GPMI_IS_MX6(this))
+ return -ENOTSUPP;
+
+ /* Stop here if this call was just a check */
+ if (chipnr < 0)
+ return 0;
+
+ /* Do the actual derivation of the controller timings */
+ gpmi_nfc_compute_timings(this, sdr);
+
+ this->hw.must_apply_timings = true;
+
+ return 0;
+}
+
+/* Clears a BCH interrupt. */
+static void gpmi_clear_bch(struct gpmi_nand_data *this)
+{
+ struct resources *r = &this->resources;
+ writel(BM_BCH_CTRL_COMPLETE_IRQ, r->bch_regs + HW_BCH_CTRL_CLR);
+}
+
+/* Returns the Ready/Busy status of the given chip. */
+static int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip)
+{
+ struct resources *r = &this->resources;
+ uint32_t mask = 0;
+ uint32_t reg = 0;
+
+ if (GPMI_IS_MX23(this)) {
+ mask = MX23_BM_GPMI_DEBUG_READY0 << chip;
+ reg = readl(r->gpmi_regs + HW_GPMI_DEBUG);
+ } else if (GPMI_IS_MX28(this) || GPMI_IS_MX6(this)) {
+ /*
+ * In the imx6, all the ready/busy pins are bound
+ * together. So we only need to check chip 0.
+ */
+ if (GPMI_IS_MX6(this))
+ chip = 0;
+
+ /* MX28 shares the same R/B register as MX6Q. */
+ mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip);
+ reg = readl(r->gpmi_regs + HW_GPMI_STAT);
+ } else
+ dev_err(this->dev, "unknown arch.\n");
+ return reg & mask;
+}
+
+static struct dma_chan *get_dma_chan(struct gpmi_nand_data *this)
+{
+ /* We use the DMA channel 0 to access all the nand chips. */
+ return this->dma_chans[0];
+}
+
+/* This will be called after the DMA operation is finished. */
+static void dma_irq_callback(void *param)
+{
+ struct gpmi_nand_data *this = param;
+ struct completion *dma_c = &this->dma_done;
+
+ complete(dma_c);
+}
+
+static int start_dma_without_bch_irq(struct gpmi_nand_data *this,
+ struct dma_async_tx_descriptor *desc)
+{
+ struct completion *dma_c = &this->dma_done;
+ unsigned long timeout;
+
+ init_completion(dma_c);
+
+ desc->callback = dma_irq_callback;
+ desc->callback_param = this;
+ dmaengine_submit(desc);
+ dma_async_issue_pending(get_dma_chan(this));
+
+ /* Wait for the interrupt from the DMA block. */
+ timeout = wait_for_completion_timeout(dma_c, msecs_to_jiffies(1000));
+ if (!timeout) {
+ dev_err(this->dev, "DMA timeout, last DMA\n");
+ gpmi_dump_info(this);
+ return -ETIMEDOUT;
+ }
+ return 0;
+}
+
+static irqreturn_t bch_irq(int irq, void *cookie)
+{
+ struct gpmi_nand_data *this = cookie;
+
+ gpmi_clear_bch(this);
+ complete(&this->bch_done);
+ return IRQ_HANDLED;
+}
+
+/*
+ * This function is used in BCH reading or BCH writing pages.
+ * It will wait for the BCH interrupt as long as ONE second.
+ * Actually, we must wait for two interrupts :
+ * [1] firstly the DMA interrupt and
+ * [2] secondly the BCH interrupt.
+ */
+static int start_dma_with_bch_irq(struct gpmi_nand_data *this,
+ struct dma_async_tx_descriptor *desc)
+{
+ struct completion *bch_c = &this->bch_done;
unsigned long timeout;
/* Prepare to receive an interrupt from the BCH block. */
@@ -526,6 +909,544 @@ int start_dma_with_bch_irq(struct gpmi_nand_data *this,
return 0;
}
+static int gpmi_send_command(struct gpmi_nand_data *this)
+{
+ struct dma_chan *channel = get_dma_chan(this);
+ struct dma_async_tx_descriptor *desc;
+ struct scatterlist *sgl;
+ int chip = this->current_chip;
+ int ret;
+ u32 pio[3];
+
+ /* [1] send out the PIO words */
+ pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__WRITE)
+ | BM_GPMI_CTRL0_WORD_LENGTH
+ | BF_GPMI_CTRL0_CS(chip, this)
+ | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+ | BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_CLE)
+ | BM_GPMI_CTRL0_ADDRESS_INCREMENT
+ | BF_GPMI_CTRL0_XFER_COUNT(this->command_length);
+ pio[1] = pio[2] = 0;
+ desc = dmaengine_prep_slave_sg(channel,
+ (struct scatterlist *)pio,
+ ARRAY_SIZE(pio), DMA_TRANS_NONE, 0);
+ if (!desc)
+ return -EINVAL;
+
+ /* [2] send out the COMMAND + ADDRESS string stored in @buffer */
+ sgl = &this->cmd_sgl;
+
+ sg_init_one(sgl, this->cmd_buffer, this->command_length);
+ dma_map_sg(this->dev, sgl, 1, DMA_TO_DEVICE);
+ desc = dmaengine_prep_slave_sg(channel,
+ sgl, 1, DMA_MEM_TO_DEV,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc)
+ return -EINVAL;
+
+ /* [3] submit the DMA */
+ ret = start_dma_without_bch_irq(this, desc);
+
+ dma_unmap_sg(this->dev, sgl, 1, DMA_TO_DEVICE);
+
+ return ret;
+}
+
+/* Can we use the upper's buffer directly for DMA? */
+static bool prepare_data_dma(struct gpmi_nand_data *this, const void *buf,
+ int len, enum dma_data_direction dr)
+{
+ struct scatterlist *sgl = &this->data_sgl;
+ int ret;
+
+ /* first try to map the upper buffer directly */
+ if (virt_addr_valid(buf) && !object_is_on_stack(buf)) {
+ sg_init_one(sgl, buf, len);
+ ret = dma_map_sg(this->dev, sgl, 1, dr);
+ if (ret == 0)
+ goto map_fail;
+
+ return true;
+ }
+
+map_fail:
+ /* We have to use our own DMA buffer. */
+ sg_init_one(sgl, this->data_buffer_dma, len);
+
+ if (dr == DMA_TO_DEVICE)
+ memcpy(this->data_buffer_dma, buf, len);
+
+ dma_map_sg(this->dev, sgl, 1, dr);
+
+ return false;
+}
+
+static int gpmi_send_data(struct gpmi_nand_data *this, const void *buf, int len)
+{
+ struct dma_async_tx_descriptor *desc;
+ struct dma_chan *channel = get_dma_chan(this);
+ int chip = this->current_chip;
+ int ret;
+ uint32_t command_mode;
+ uint32_t address;
+ u32 pio[2];
+
+ /* [1] PIO */
+ command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE;
+ address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+
+ pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+ | BM_GPMI_CTRL0_WORD_LENGTH
+ | BF_GPMI_CTRL0_CS(chip, this)
+ | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+ | BF_GPMI_CTRL0_ADDRESS(address)
+ | BF_GPMI_CTRL0_XFER_COUNT(len);
+ pio[1] = 0;
+ desc = dmaengine_prep_slave_sg(channel, (struct scatterlist *)pio,
+ ARRAY_SIZE(pio), DMA_TRANS_NONE, 0);
+ if (!desc)
+ return -EINVAL;
+
+ /* [2] send DMA request */
+ prepare_data_dma(this, buf, len, DMA_TO_DEVICE);
+ desc = dmaengine_prep_slave_sg(channel, &this->data_sgl,
+ 1, DMA_MEM_TO_DEV,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc)
+ return -EINVAL;
+
+ /* [3] submit the DMA */
+ ret = start_dma_without_bch_irq(this, desc);
+
+ dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_TO_DEVICE);
+
+ return ret;
+}
+
+static int gpmi_read_data(struct gpmi_nand_data *this, void *buf, int len)
+{
+ struct dma_async_tx_descriptor *desc;
+ struct dma_chan *channel = get_dma_chan(this);
+ int chip = this->current_chip;
+ int ret;
+ u32 pio[2];
+ bool direct;
+
+ /* [1] : send PIO */
+ pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(BV_GPMI_CTRL0_COMMAND_MODE__READ)
+ | BM_GPMI_CTRL0_WORD_LENGTH
+ | BF_GPMI_CTRL0_CS(chip, this)
+ | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+ | BF_GPMI_CTRL0_ADDRESS(BV_GPMI_CTRL0_ADDRESS__NAND_DATA)
+ | BF_GPMI_CTRL0_XFER_COUNT(len);
+ pio[1] = 0;
+ desc = dmaengine_prep_slave_sg(channel,
+ (struct scatterlist *)pio,
+ ARRAY_SIZE(pio), DMA_TRANS_NONE, 0);
+ if (!desc)
+ return -EINVAL;
+
+ /* [2] : send DMA request */
+ direct = prepare_data_dma(this, buf, len, DMA_FROM_DEVICE);
+ desc = dmaengine_prep_slave_sg(channel, &this->data_sgl,
+ 1, DMA_DEV_TO_MEM,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc)
+ return -EINVAL;
+
+ /* [3] : submit the DMA */
+
+ ret = start_dma_without_bch_irq(this, desc);
+
+ dma_unmap_sg(this->dev, &this->data_sgl, 1, DMA_FROM_DEVICE);
+ if (!direct)
+ memcpy(buf, this->data_buffer_dma, len);
+
+ return ret;
+}
+
+static int gpmi_send_page(struct gpmi_nand_data *this, dma_addr_t payload,
+ dma_addr_t auxiliary)
+{
+ struct bch_geometry *geo = &this->bch_geometry;
+ uint32_t command_mode;
+ uint32_t address;
+ uint32_t ecc_command;
+ uint32_t buffer_mask;
+ struct dma_async_tx_descriptor *desc;
+ struct dma_chan *channel = get_dma_chan(this);
+ int chip = this->current_chip;
+ u32 pio[6];
+
+ /* A DMA descriptor that does an ECC page read. */
+ command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WRITE;
+ address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+ ecc_command = BV_GPMI_ECCCTRL_ECC_CMD__BCH_ENCODE;
+ buffer_mask = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE |
+ BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY;
+
+ pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+ | BM_GPMI_CTRL0_WORD_LENGTH
+ | BF_GPMI_CTRL0_CS(chip, this)
+ | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+ | BF_GPMI_CTRL0_ADDRESS(address)
+ | BF_GPMI_CTRL0_XFER_COUNT(0);
+ pio[1] = 0;
+ pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC
+ | BF_GPMI_ECCCTRL_ECC_CMD(ecc_command)
+ | BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask);
+ pio[3] = geo->page_size;
+ pio[4] = payload;
+ pio[5] = auxiliary;
+
+ desc = dmaengine_prep_slave_sg(channel,
+ (struct scatterlist *)pio,
+ ARRAY_SIZE(pio), DMA_TRANS_NONE,
+ DMA_CTRL_ACK);
+ if (!desc)
+ return -EINVAL;
+
+ return start_dma_with_bch_irq(this, desc);
+}
+
+static int gpmi_read_page(struct gpmi_nand_data *this, dma_addr_t payload,
+ dma_addr_t auxiliary)
+{
+ struct bch_geometry *geo = &this->bch_geometry;
+ uint32_t command_mode;
+ uint32_t address;
+ uint32_t ecc_command;
+ uint32_t buffer_mask;
+ struct dma_async_tx_descriptor *desc;
+ struct dma_chan *channel = get_dma_chan(this);
+ int chip = this->current_chip;
+ u32 pio[6];
+
+ /* [1] Wait for the chip to report ready. */
+ command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY;
+ address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+
+ pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+ | BM_GPMI_CTRL0_WORD_LENGTH
+ | BF_GPMI_CTRL0_CS(chip, this)
+ | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+ | BF_GPMI_CTRL0_ADDRESS(address)
+ | BF_GPMI_CTRL0_XFER_COUNT(0);
+ pio[1] = 0;
+ desc = dmaengine_prep_slave_sg(channel,
+ (struct scatterlist *)pio, 2,
+ DMA_TRANS_NONE, 0);
+ if (!desc)
+ return -EINVAL;
+
+ /* [2] Enable the BCH block and read. */
+ command_mode = BV_GPMI_CTRL0_COMMAND_MODE__READ;
+ address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+ ecc_command = BV_GPMI_ECCCTRL_ECC_CMD__BCH_DECODE;
+ buffer_mask = BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_PAGE
+ | BV_GPMI_ECCCTRL_BUFFER_MASK__BCH_AUXONLY;
+
+ pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+ | BM_GPMI_CTRL0_WORD_LENGTH
+ | BF_GPMI_CTRL0_CS(chip, this)
+ | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+ | BF_GPMI_CTRL0_ADDRESS(address)
+ | BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
+
+ pio[1] = 0;
+ pio[2] = BM_GPMI_ECCCTRL_ENABLE_ECC
+ | BF_GPMI_ECCCTRL_ECC_CMD(ecc_command)
+ | BF_GPMI_ECCCTRL_BUFFER_MASK(buffer_mask);
+ pio[3] = geo->page_size;
+ pio[4] = payload;
+ pio[5] = auxiliary;
+ desc = dmaengine_prep_slave_sg(channel,
+ (struct scatterlist *)pio,
+ ARRAY_SIZE(pio), DMA_TRANS_NONE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc)
+ return -EINVAL;
+
+ /* [3] Disable the BCH block */
+ command_mode = BV_GPMI_CTRL0_COMMAND_MODE__WAIT_FOR_READY;
+ address = BV_GPMI_CTRL0_ADDRESS__NAND_DATA;
+
+ pio[0] = BF_GPMI_CTRL0_COMMAND_MODE(command_mode)
+ | BM_GPMI_CTRL0_WORD_LENGTH
+ | BF_GPMI_CTRL0_CS(chip, this)
+ | BF_GPMI_CTRL0_LOCK_CS(LOCK_CS_ENABLE, this)
+ | BF_GPMI_CTRL0_ADDRESS(address)
+ | BF_GPMI_CTRL0_XFER_COUNT(geo->page_size);
+ pio[1] = 0;
+ pio[2] = 0; /* clear GPMI_HW_GPMI_ECCCTRL, disable the BCH. */
+ desc = dmaengine_prep_slave_sg(channel,
+ (struct scatterlist *)pio, 3,
+ DMA_TRANS_NONE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc)
+ return -EINVAL;
+
+ /* [4] submit the DMA */
+ return start_dma_with_bch_irq(this, desc);
+}
+
+/**
+ * gpmi_copy_bits - copy bits from one memory region to another
+ * @dst: destination buffer
+ * @dst_bit_off: bit offset we're starting to write at
+ * @src: source buffer
+ * @src_bit_off: bit offset we're starting to read from
+ * @nbits: number of bits to copy
+ *
+ * This functions copies bits from one memory region to another, and is used by
+ * the GPMI driver to copy ECC sections which are not guaranteed to be byte
+ * aligned.
+ *
+ * src and dst should not overlap.
+ *
+ */
+static void gpmi_copy_bits(u8 *dst, size_t dst_bit_off, const u8 *src,
+ size_t src_bit_off, size_t nbits)
+{
+ size_t i;
+ size_t nbytes;
+ u32 src_buffer = 0;
+ size_t bits_in_src_buffer = 0;
+
+ if (!nbits)
+ return;
+
+ /*
+ * Move src and dst pointers to the closest byte pointer and store bit
+ * offsets within a byte.
+ */
+ src += src_bit_off / 8;
+ src_bit_off %= 8;
+
+ dst += dst_bit_off / 8;
+ dst_bit_off %= 8;
+
+ /*
+ * Initialize the src_buffer value with bits available in the first
+ * byte of data so that we end up with a byte aligned src pointer.
+ */
+ if (src_bit_off) {
+ src_buffer = src[0] >> src_bit_off;
+ if (nbits >= (8 - src_bit_off)) {
+ bits_in_src_buffer += 8 - src_bit_off;
+ } else {
+ src_buffer &= GENMASK(nbits - 1, 0);
+ bits_in_src_buffer += nbits;
+ }
+ nbits -= bits_in_src_buffer;
+ src++;
+ }
+
+ /* Calculate the number of bytes that can be copied from src to dst. */
+ nbytes = nbits / 8;
+
+ /* Try to align dst to a byte boundary. */
+ if (dst_bit_off) {
+ if (bits_in_src_buffer < (8 - dst_bit_off) && nbytes) {
+ src_buffer |= src[0] << bits_in_src_buffer;
+ bits_in_src_buffer += 8;
+ src++;
+ nbytes--;
+ }
+
+ if (bits_in_src_buffer >= (8 - dst_bit_off)) {
+ dst[0] &= GENMASK(dst_bit_off - 1, 0);
+ dst[0] |= src_buffer << dst_bit_off;
+ src_buffer >>= (8 - dst_bit_off);
+ bits_in_src_buffer -= (8 - dst_bit_off);
+ dst_bit_off = 0;
+ dst++;
+ if (bits_in_src_buffer > 7) {
+ bits_in_src_buffer -= 8;
+ dst[0] = src_buffer;
+ dst++;
+ src_buffer >>= 8;
+ }
+ }
+ }
+
+ if (!bits_in_src_buffer && !dst_bit_off) {
+ /*
+ * Both src and dst pointers are byte aligned, thus we can
+ * just use the optimized memcpy function.
+ */
+ if (nbytes)
+ memcpy(dst, src, nbytes);
+ } else {
+ /*
+ * src buffer is not byte aligned, hence we have to copy each
+ * src byte to the src_buffer variable before extracting a byte
+ * to store in dst.
+ */
+ for (i = 0; i < nbytes; i++) {
+ src_buffer |= src[i] << bits_in_src_buffer;
+ dst[i] = src_buffer;
+ src_buffer >>= 8;
+ }
+ }
+ /* Update dst and src pointers */
+ dst += nbytes;
+ src += nbytes;
+
+ /*
+ * nbits is the number of remaining bits. It should not exceed 8 as
+ * we've already copied as much bytes as possible.
+ */
+ nbits %= 8;
+
+ /*
+ * If there's no more bits to copy to the destination and src buffer
+ * was already byte aligned, then we're done.
+ */
+ if (!nbits && !bits_in_src_buffer)
+ return;
+
+ /* Copy the remaining bits to src_buffer */
+ if (nbits)
+ src_buffer |= (*src & GENMASK(nbits - 1, 0)) <<
+ bits_in_src_buffer;
+ bits_in_src_buffer += nbits;
+
+ /*
+ * In case there were not enough bits to get a byte aligned dst buffer
+ * prepare the src_buffer variable to match the dst organization (shift
+ * src_buffer by dst_bit_off and retrieve the least significant bits
+ * from dst).
+ */
+ if (dst_bit_off)
+ src_buffer = (src_buffer << dst_bit_off) |
+ (*dst & GENMASK(dst_bit_off - 1, 0));
+ bits_in_src_buffer += dst_bit_off;
+
+ /*
+ * Keep most significant bits from dst if we end up with an unaligned
+ * number of bits.
+ */
+ nbytes = bits_in_src_buffer / 8;
+ if (bits_in_src_buffer % 8) {
+ src_buffer |= (dst[nbytes] &
+ GENMASK(7, bits_in_src_buffer % 8)) <<
+ (nbytes * 8);
+ nbytes++;
+ }
+
+ /* Copy the remaining bytes to dst */
+ for (i = 0; i < nbytes; i++) {
+ dst[i] = src_buffer;
+ src_buffer >>= 8;
+ }
+}
+
+/* add our owner bbt descriptor */
+static uint8_t scan_ff_pattern[] = { 0xff };
+static struct nand_bbt_descr gpmi_bbt_descr = {
+ .options = 0,
+ .offs = 0,
+ .len = 1,
+ .pattern = scan_ff_pattern
+};
+
+/*
+ * We may change the layout if we can get the ECC info from the datasheet,
+ * else we will use all the (page + OOB).
+ */
+static int gpmi_ooblayout_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct gpmi_nand_data *this = nand_get_controller_data(chip);
+ struct bch_geometry *geo = &this->bch_geometry;
+
+ if (section)
+ return -ERANGE;
+
+ oobregion->offset = 0;
+ oobregion->length = geo->page_size - mtd->writesize;
+
+ return 0;
+}
+
+static int gpmi_ooblayout_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct gpmi_nand_data *this = nand_get_controller_data(chip);
+ struct bch_geometry *geo = &this->bch_geometry;
+
+ if (section)
+ return -ERANGE;
+
+ /* The available oob size we have. */
+ if (geo->page_size < mtd->writesize + mtd->oobsize) {
+ oobregion->offset = geo->page_size - mtd->writesize;
+ oobregion->length = mtd->oobsize - oobregion->offset;
+ }
+
+ return 0;
+}
+
+static const char * const gpmi_clks_for_mx2x[] = {
+ "gpmi_io",
+};
+
+static const struct mtd_ooblayout_ops gpmi_ooblayout_ops = {
+ .ecc = gpmi_ooblayout_ecc,
+ .free = gpmi_ooblayout_free,
+};
+
+static const struct gpmi_devdata gpmi_devdata_imx23 = {
+ .type = IS_MX23,
+ .bch_max_ecc_strength = 20,
+ .max_chain_delay = 16000,
+ .clks = gpmi_clks_for_mx2x,
+ .clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
+};
+
+static const struct gpmi_devdata gpmi_devdata_imx28 = {
+ .type = IS_MX28,
+ .bch_max_ecc_strength = 20,
+ .max_chain_delay = 16000,
+ .clks = gpmi_clks_for_mx2x,
+ .clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
+};
+
+static const char * const gpmi_clks_for_mx6[] = {
+ "gpmi_io", "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch",
+};
+
+static const struct gpmi_devdata gpmi_devdata_imx6q = {
+ .type = IS_MX6Q,
+ .bch_max_ecc_strength = 40,
+ .max_chain_delay = 12000,
+ .clks = gpmi_clks_for_mx6,
+ .clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
+};
+
+static const struct gpmi_devdata gpmi_devdata_imx6sx = {
+ .type = IS_MX6SX,
+ .bch_max_ecc_strength = 62,
+ .max_chain_delay = 12000,
+ .clks = gpmi_clks_for_mx6,
+ .clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
+};
+
+static const char * const gpmi_clks_for_mx7d[] = {
+ "gpmi_io", "gpmi_bch_apb",
+};
+
+static const struct gpmi_devdata gpmi_devdata_imx7d = {
+ .type = IS_MX7D,
+ .bch_max_ecc_strength = 62,
+ .max_chain_delay = 12000,
+ .clks = gpmi_clks_for_mx7d,
+ .clks_count = ARRAY_SIZE(gpmi_clks_for_mx7d),
+};
+
static int acquire_register_block(struct gpmi_nand_data *this,
const char *res_name)
{
diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
index a804a4a5bd46..e001c84b75fa 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
@@ -159,40 +159,6 @@ struct gpmi_nand_data {
void *private;
};
-/* Common Services */
-int common_nfc_set_geometry(struct gpmi_nand_data *);
-struct dma_chan *get_dma_chan(struct gpmi_nand_data *);
-bool prepare_data_dma(struct gpmi_nand_data *, const void *buf, int len,
- enum dma_data_direction dr);
-int start_dma_without_bch_irq(struct gpmi_nand_data *,
- struct dma_async_tx_descriptor *);
-int start_dma_with_bch_irq(struct gpmi_nand_data *,
- struct dma_async_tx_descriptor *);
-
-/* GPMI-NAND helper function library */
-int gpmi_init(struct gpmi_nand_data *);
-void gpmi_clear_bch(struct gpmi_nand_data *);
-void gpmi_dump_info(struct gpmi_nand_data *);
-int bch_set_geometry(struct gpmi_nand_data *);
-int gpmi_is_ready(struct gpmi_nand_data *, unsigned chip);
-int gpmi_send_command(struct gpmi_nand_data *);
-int gpmi_enable_clk(struct gpmi_nand_data *this);
-int gpmi_disable_clk(struct gpmi_nand_data *this);
-int gpmi_setup_data_interface(struct nand_chip *chip, int chipnr,
- const struct nand_data_interface *conf);
-void gpmi_nfc_apply_timings(struct gpmi_nand_data *this);
-int gpmi_read_data(struct gpmi_nand_data *, void *buf, int len);
-int gpmi_send_data(struct gpmi_nand_data *, const void *buf, int len);
-
-int gpmi_send_page(struct gpmi_nand_data *,
- dma_addr_t payload, dma_addr_t auxiliary);
-int gpmi_read_page(struct gpmi_nand_data *,
- dma_addr_t payload, dma_addr_t auxiliary);
-
-void gpmi_copy_bits(u8 *dst, size_t dst_bit_off,
- const u8 *src, size_t src_bit_off,
- size_t nbits);
-
/* BCH : Status Block Completion Codes */
#define STATUS_GOOD 0x00
#define STATUS_ERASED 0xff
--
2.20.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
[PATCH 03/14] mtd: rawnand: gpmi: move all driver code into single file
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: [PATCH 03/14] mtd: rawnand: gpmi: move all driver code into single file
- From: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
- Date: Tue, 21 May 2019 09:06:32 +0200
- Cc: kernel@xxxxxxxxxxxxxx, Richard Weinberger <richard@xxxxxx>, Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>, Vinod Koul <vkoul@xxxxxxxxxx>, NXP Linux Team <linux-imx@xxxxxxx>, Fabio Estevam <festevam@xxxxxxxxx>, Miquel Raynal <miquel.raynal@xxxxxxxxxxx>, Han Xu <han.xu@xxxxxxx>, Shawn Guo <shawnguo@xxxxxxxxxx>
- In-reply-to: <20190521070643.6244-1-s.hauer@pengutronix.de>
- References: <20190521070643.6244-1-s.hauer@pengutronix.de>
- Follow-Ups:
- Re: [PATCH 03/14] mtd: rawnand: gpmi: move all driver code into single file
- From: Miquel Raynal
- Re: [PATCH 03/14] mtd: rawnand: gpmi: move all driver code into single file
- From: Sascha Hauer
- Re: [PATCH 03/14] mtd: rawnand: gpmi: move all driver code into single file
- References:
- [PATCH v4 00/14] Implement exec_op for GPMI nand driver
- From: Sascha Hauer
- [PATCH v4 00/14] Implement exec_op for GPMI nand driver
- Prev by Date: [PATCH 09/14] mtd: rawnand: gpmi: use runtime PM to manage clocks
- Next by Date: [PATCH 04/14] mtd: rawnand: gpmi: remove unused variable
- Previous by thread: Re: [PATCH 09/14] mtd: rawnand: gpmi: use runtime PM to manage clocks
- Next by thread: Re: [PATCH 03/14] mtd: rawnand: gpmi: move all driver code into single file
- Index(es):
 |