[PATCH v2 01/10] mtd: cfi_cmdset_0002: Change do_write_oneword() to use chip_good()

[Tokunori Ikegami <ikegami@xxxxxxxxxxxxxxxxxxxx>]

This is required for OpenWrt Project to result the flash write issue as
below patche.
<https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=ddc11c3932c7b7b7df7d5fbd48f207e77619eaa7>

Also the original patch in OpenWRT is below.
<https://github.com/openwrt/openwrt/blob/v18.06.0/target/linux/ar71xx/patches-4.9/403-mtd_fix_cfi_cmdset_0002_status_check.patch>

So change to use chip_good() instead of chip_ready().

The reason to use chip_good() is that just actually fix the issue.
And also in the past I had fixed the erase function also as same way by the
patch below.
  <https://patchwork.ozlabs.org/patch/922656/>
    Note: The reason for the patch for erase is same.

In my understanding the chip_ready() is just checked the value twice from
flash.
So I think that sometimes incorrect value is read twice and it is depended
on the flash device behavior but not sure..

So change to use chip_good() instead of chip_ready().

Signed-off-by: Tokunori Ikegami <ikegami@xxxxxxxxxxxxxxxxxxxx>
Signed-off-by: Hauke Mehrtens <hauke@xxxxxxxxxx>
Signed-off-by: Koen Vandeputte <koen.vandeputte@xxxxxxxxxxxx>
Signed-off-by: Fabio Bettoni <fbettoni@xxxxxxxxx>
Co-Developed-by: Hauke Mehrtens <hauke@xxxxxxxxxx>
Co-Developed-by: Koen Vandeputte <koen.vandeputte@xxxxxxxxxxxx>
Co-Developed-by: Fabio Bettoni <fbettoni@xxxxxxxxx>
Reported-by: Fabio Bettoni <fbettoni@xxxxxxxxx>
Cc: Chris Packham <chris.packham@xxxxxxxxxxxxxxxxxxx>
Cc: Joakim Tjernlund <Joakim.Tjernlund@xxxxxxxxxxxx>
Cc: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx
Cc: stable@xxxxxxxxxxxxxxx
---
Changes since v1:
- Just update the commit message.

 drivers/mtd/chips/cfi_cmdset_0002.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

diff --git a/drivers/mtd/chips/cfi_cmdset_0002.c b/drivers/mtd/chips/cfi_cmdset_0002.c
index 72428b6bfc47..251c9e1675bd 100644
--- a/drivers/mtd/chips/cfi_cmdset_0002.c
+++ b/drivers/mtd/chips/cfi_cmdset_0002.c
@@ -1627,31 +1627,37 @@ static int __xipram do_write_oneword(struct map_info *map, struct flchip *chip,
 			continue;
 		}
 
-		if (time_after(jiffies, timeo) && !chip_ready(map, adr)){
+		if (chip_good(map, adr, datum))
+			break;
+
+		if (time_after(jiffies, timeo)){
 			xip_enable(map, chip, adr);
 			printk(KERN_WARNING "MTD %s(): software timeout\n", __func__);
 			xip_disable(map, chip, adr);
+			ret = -EIO;
 			break;
 		}
 
-		if (chip_ready(map, adr))
-			break;
-
 		/* Latency issues. Drop the lock, wait a while and retry */
 		UDELAY(map, chip, adr, 1);
 	}
+
 	/* Did we succeed? */
-	if (!chip_good(map, adr, datum)) {
+	if (ret) {
 		/* reset on all failures. */
 		map_write(map, CMD(0xF0), chip->start);
 		/* FIXME - should have reset delay before continuing */
 
-		if (++retry_cnt <= MAX_RETRIES)
+		if (++retry_cnt <= MAX_RETRIES) {
+			ret = 0;
 			goto retry;
+		}
 
 		ret = -EIO;
 	}
+
 	xip_enable(map, chip, adr);
+
  op_done:
 	if (mode == FL_OTP_WRITE)
 		otp_exit(map, chip, adr, map_bankwidth(map));
-- 
2.18.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/