RE: [PATCH 1/4] spi: add support for octal I/O data transfer

[Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx>]

Hi Boris,

> -----Original Message-----
> From: Yogesh Narayan Gaur
> Sent: Thursday, October 4, 2018 2:56 PM
> To: 'Boris Brezillon' <boris.brezillon@xxxxxxxxxxx>
> Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx; marek.vasut@xxxxxxxxx; vigneshr@xxxxxx;
> linux-spi@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; robh@xxxxxxxxxx;
> mark.rutland@xxxxxxx; shawnguo@xxxxxxxxxx; linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx; computersforpeace@xxxxxxxxx;
> frieder.schrempf@xxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
> Subject: RE: [PATCH 1/4] spi: add support for octal I/O data transfer
> 
> Hi Boris,
> 
> > -----Original Message-----
> > From: Boris Brezillon [mailto:boris.brezillon@xxxxxxxxxxx]
> > Sent: Thursday, October 4, 2018 2:50 PM
> > To: Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx>
> > Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx; marek.vasut@xxxxxxxxx;
> > vigneshr@xxxxxx; linux-spi@xxxxxxxxxxxxxxx;
> > devicetree@xxxxxxxxxxxxxxx; robh@xxxxxxxxxx; mark.rutland@xxxxxxx;
> > shawnguo@xxxxxxxxxx; linux-arm- kernel@xxxxxxxxxxxxxxxxxxx;
> > computersforpeace@xxxxxxxxx; frieder.schrempf@xxxxxxxxx;
> > linux-kernel@xxxxxxxxxxxxxxx
> > Subject: Re: [PATCH 1/4] spi: add support for octal I/O data transfer
> >
> > On Thu, 4 Oct 2018 09:14:36 +0000
> > Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx> wrote:
> >
> > > Hi Boris,
> > >
> > > > -----Original Message-----
> > > > From: Boris Brezillon [mailto:boris.brezillon@xxxxxxxxxxx]
> > > > Sent: Thursday, October 4, 2018 2:35 PM
> > > > To: Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx>
> > > > Cc: linux-mtd@xxxxxxxxxxxxxxxxxxx; marek.vasut@xxxxxxxxx;
> > > > vigneshr@xxxxxx; linux-spi@xxxxxxxxxxxxxxx;
> > > > devicetree@xxxxxxxxxxxxxxx; robh@xxxxxxxxxx; mark.rutland@xxxxxxx;
> > > > shawnguo@xxxxxxxxxx; linux-arm- kernel@xxxxxxxxxxxxxxxxxxx;
> > > > computersforpeace@xxxxxxxxx; frieder.schrempf@xxxxxxxxx;
> > > > linux-kernel@xxxxxxxxxxxxxxx Subject: Re: [PATCH 1/4] spi: add
> > > > support for octal I/O data transfer
> > > >
> > > > Hi Yogesh,
> > > >
[...]
> > > > > +#define	SPI_RX_OCTAL
> > > > > 0x2000			/* receive with 8 wires
> > > > */
> > > > >  	int			irq;
> > > > >  	void			*controller_state;
> > > > >  	void			*controller_data;
> > > >
> > > > You're still not updating spi-mem.c to check those flags and
> > > > SPI_MEM_MAX_BUSWIDTH is not updated to match the new limit (8
> > > > instead of 4).
> > > >
> > > Yes and its strange that my octal mode communication is working fine
> > > without adding support in spi-mem.c and that's why this has been
> > > missed from me.
> >
> > Are you based on top of spi-next?
> 
> Ok, that might be the reason. I have rebased few days back.
> Would rebase with current tip and add support in spi-mem interface too.

I have rebased spi-next and currently on top but still my octal command support is working fine without any issue with current shared patch series, performed data sanity.

=>  git log  --pretty=oneline -3
	496c415717b8bb7d37181127fcfad0ba450eb10d mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
	2336d3a7b125683c9e8b25d6efa6064310d19dbe mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
	e55841874471282d32eec595997afce43a5f55c0 mtd: spi-nor: Support controllers with limited TX FIFO size

GIT Repo - 	git://git.infradead.org/linux-mtd.git
Branch -	remotes/origin/spi-nor/next

Also, I am not able to find string SPI_MEM_MAX_BUSWIDTH in current source code, can you share the GIT details where these changes are pushed.
--
Regards
Yogesh Gaur.

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/