Re: [LINUX PATCH v10 2/2] mtd: rawnand: arasan: Add support for Arasan NAND Flash Controller

[Boris Brezillon <boris.brezillon@xxxxxxxxxxx>]

Hi Naga,

On Fri, 17 Aug 2018 18:49:24 +0530
Naga Sureshkumar Relli <naga.sureshkumar.relli@xxxxxxxxxx> wrote:

> +static int anfc_exec_op_cmd(struct nand_chip *chip,
> +				   const struct nand_subop *subop)
> +{
> +	const struct nand_op_instr *instr;
> +	struct anfc_op nfc_op = {};
> +	struct anfc_nand_chip *achip = to_anfc_nand(chip);
> +	struct anfc_nand_controller *nfc = to_anfc(chip->controller);
> +	struct mtd_info *mtd = nand_to_mtd(chip);
> +	u32 addrcycles;
> +	unsigned int op_id, len = 0;
> +	bool reading;
> +
> +	anfc_parse_instructions(chip, subop, &nfc_op);
> +	instr = nfc_op.data_instr;
> +	op_id = nfc_op.data_instr_idx;
> +	if (nfc_op.data_instr)
> +		len = nand_subop_get_data_len(subop, op_id);
> +
> +	/*
> +	 * The switch case is to prepare a command and to set page/column
> +	 * address. Arasan NAND controller has program register(Off: 0x10)),
> +	 * which needs to be set for every command.
> +	 * Ex: When NAND_CMD_RESET is issued, then we need to set reset bit
> +	 * in program_register. etc..
> +	 */
> +	switch (nfc_op.cmnds[0]) {
> +	case NAND_CMD_SEQIN:
> +		addrcycles = achip->raddr_cycles + achip->caddr_cycles;
> +
> +		anfc_prepare_cmd(nfc, nfc_op.cmnds[0], NAND_CMD_PAGEPROG, 1,
> +				 mtd->writesize, addrcycles);
> +		anfc_setpagecoladdr(nfc, nfc_op.row, nfc_op.col);
> +		break;
> +	case NAND_CMD_READOOB:
> +		nfc_op.col += mtd->writesize;
> +	case NAND_CMD_READ0:
> +	case NAND_CMD_READ1:
> +		addrcycles = achip->raddr_cycles + achip->caddr_cycles;
> +		anfc_prepare_cmd(nfc, NAND_CMD_READ0, NAND_CMD_READSTART, 1,
> +				 mtd->writesize, addrcycles);
> +		anfc_setpagecoladdr(nfc, nfc_op.row, nfc_op.col);
> +		if (!nfc_op.data_instr)
> +			return 0;
> +
> +		anfc_read_data_op(mtd, instr->ctx.data.buf.in, len);
> +		break;
> +	case NAND_CMD_RNDOUT:
> +		anfc_prepare_cmd(nfc, nfc_op.cmnds[0], NAND_CMD_RNDOUTSTART, 1,
> +				 mtd->writesize, 2);
> +		anfc_setpagecoladdr(nfc, nfc_op.row, nfc_op.col);
> +		nfc->prog = PROG_PGRD;
> +		break;
> +	case NAND_CMD_PARAM:
> +		anfc_prepare_cmd(nfc, nfc_op.cmnds[0], 0, 0, 0, 1);
> +		anfc_setpagecoladdr(nfc, nfc_op.row, nfc_op.col);
> +		nfc->prog = PROG_RDPARAM;
> +		break;
> +	case NAND_CMD_READID:
> +		anfc_prepare_cmd(nfc, nfc_op.cmnds[0], 0, 0, 0, 1);
> +		anfc_setpagecoladdr(nfc, nfc_op.row, nfc_op.col);
> +		nfc->prog = PROG_RDID;
> +		break;
> +	case NAND_CMD_GET_FEATURES:
> +		anfc_prepare_cmd(nfc, nfc_op.cmnds[0], 0, 0, 0, 1);
> +		anfc_setpagecoladdr(nfc, nfc_op.row, nfc_op.col);
> +		nfc->prog = PROG_GET_FEATURE;
> +		break;
> +	case NAND_CMD_SET_FEATURES:
> +		anfc_prepare_cmd(nfc, nfc_op.cmnds[0], 0, 0, 0, 1);
> +		anfc_setpagecoladdr(nfc, nfc_op.row, nfc_op.col);
> +		nfc->prog = PROG_SET_FEATURE;
> +		break;
> +	case NAND_CMD_ERASE1:
> +		anfc_erase_function(chip, nfc_op);
> +		break;
> +	default:
> +		break;
> +	}

Looks like you have one of these smart controllers where everything is
hardcoded and new commands (like vendor specific commands) can't be
supported, and we're back to abusing ->exec_op(), just like ->cmdfunc()
was abused.

Don't you have a way to send raw CMD/ADDR/DATA cycles? If not, then
we'll have to consider other options, because I don't want to go back
to the situation we are in with ->cmdfunc().

Maybe I already asked, but is there a public spec for this IP?

Thanks,

Boris

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/