On Wed, Jan 04, 2023 at 09:59:35PM +0200, Bitterblue Smith wrote: > On 04/01/2023 01:01, Chris Morgan wrote: > > On Wed, Dec 28, 2022 at 12:30:20AM +0100, Martin Blumenstingl wrote: > >> Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as > >> well as the existing RTL8821C chipset code. > >> > > > > Unfortunately, this doesn't work for me. I applied it on top of 6.2-rc2 > > master and I get errors during probe (it appears the firmware never > > loads). > > > > Relevant dmesg logs are as follows: > > > > [ 0.989545] mmc2: new high speed SDIO card at address 0001 > > [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 > > [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 > > [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 > > [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 > > [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 > > [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 > > [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 > > [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 > > > > The error of "sdio read32 failed (0x1700): -110" then repeats several > > hundred times, then I get this: > > > > [ 1.066294] rtw_8821cs mmc2:0001:1: failed to download firmware > > [ 1.066367] rtw_8821cs mmc2:0001:1: sdio read16 failed (0x80): -110 > > [ 1.066417] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x100): -110 > > [ 1.066697] rtw_8821cs mmc2:0001:1: failed to setup chip efuse info > > [ 1.066703] rtw_8821cs mmc2:0001:1: failed to setup chip information > > [ 1.066839] rtw_8821cs: probe of mmc2:0001:1 failed with error -16 > > > > The hardware I am using is an rtl8821cs that I can confirm was working > > with a previous driver. > > > > Thank you. > > > The USB-based RTL8811CU also doesn't work, with suspiciously similar > errors: > > Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0: Firmware version 24.11.0, H2C version 12 > Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0 wlp0s20f0u2: renamed from wlan0 > Dec 25 21:43:40 home kernel: rtw_8821cu 1-2:1.0: read register 0x5 failed with -110 Is this the very first register access or are there other register accesses before that actually do work? Sascha -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
