On 04/01/2023 01:01, Chris Morgan wrote: > On Wed, Dec 28, 2022 at 12:30:20AM +0100, Martin Blumenstingl wrote: >> Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as >> well as the existing RTL8821C chipset code. >> > > Unfortunately, this doesn't work for me. I applied it on top of 6.2-rc2 > master and I get errors during probe (it appears the firmware never > loads). > > Relevant dmesg logs are as follows: > > [ 0.989545] mmc2: new high speed SDIO card at address 0001 > [ 0.989993] rtw_8821cs mmc2:0001:1: Firmware version 24.8.0, H2C version 12 > [ 1.005684] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x14): -110 > [ 1.005737] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1080): -110 > [ 1.005789] rtw_8821cs mmc2:0001:1: sdio write32 failed (0x11080): -110 > [ 1.005840] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x3): -110 > [ 1.005920] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x1103): -110 > [ 1.005998] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x80): -110 > [ 1.006078] rtw_8821cs mmc2:0001:1: sdio read32 failed (0x1700): -110 > > The error of "sdio read32 failed (0x1700): -110" then repeats several > hundred times, then I get this: > > [ 1.066294] rtw_8821cs mmc2:0001:1: failed to download firmware > [ 1.066367] rtw_8821cs mmc2:0001:1: sdio read16 failed (0x80): -110 > [ 1.066417] rtw_8821cs mmc2:0001:1: sdio read8 failed (0x100): -110 > [ 1.066697] rtw_8821cs mmc2:0001:1: failed to setup chip efuse info > [ 1.066703] rtw_8821cs mmc2:0001:1: failed to setup chip information > [ 1.066839] rtw_8821cs: probe of mmc2:0001:1 failed with error -16 > > The hardware I am using is an rtl8821cs that I can confirm was working > with a previous driver. > > Thank you. > The USB-based RTL8811CU also doesn't work, with suspiciously similar errors: Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0: Firmware version 24.11.0, H2C version 12 Dec 25 21:43:37 home kernel: rtw_8821cu 1-2:1.0 wlp0s20f0u2: renamed from wlan0 Dec 25 21:43:40 home kernel: rtw_8821cu 1-2:1.0: read register 0x5 failed with -110 Dec 25 21:43:41 home kernel: rtw_8821cu 1-2:1.0: read register 0x20 failed with -110 Dec 25 21:44:11 home kernel: rtw_8821cu 1-2:1.0: write register 0x20 failed with -110 Dec 25 21:44:12 home kernel: rtw_8821cu 1-2:1.0: read register 0x7c failed with -110 Dec 25 21:44:43 home kernel: rtw_8821cu 1-2:1.0: write register 0x7c failed with -110 Dec 25 21:44:44 home kernel: rtw_8821cu 1-2:1.0: read register 0x1080 failed with -110 Dec 25 21:45:16 home kernel: rtw_8821cu 1-2:1.0: write register 0x1080 failed with -110 Dec 25 21:46:47 home kernel: rtw_8821cu 1-3:1.0: Firmware version 24.11.0, H2C version 12 Dec 25 21:46:47 home kernel: rtw_8821cu 1-3:1.0 wlp0s20f0u3: renamed from wlan0 Dec 25 21:46:55 home kernel: rtw_8821cu 1-3:1.0: failed to poll offset=0x5 mask=0x1 value=0x0 Dec 25 21:46:55 home kernel: rtw_8821cu 1-3:1.0: mac power on failed Dec 25 21:46:55 home kernel: rtw_8821cu 1-3:1.0: failed to power on mac I tested with https://github.com/lwfinger/rtw88/ which should have the same code as wireless-next currently.
