On 09/07/18 06:19, Chunyan Zhang wrote:
> As SD Host Controller Specification v4.10 documents:
> Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
> Selection of Auto CMD depends on setting of CMD23 Enable in the Host
> Control 2 register which indicates whether card supports CMD23. If CMD23
> Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
> used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
> recommended rather than use of Auto CMD12 Enable or Auto CMD23
> Enable.
>
> This patch add this new mode support.
>
> Signed-off-by: Chunyan Zhang <zhang.chunyan@xxxxxxxxxx>
> ---
> drivers/mmc/host/sdhci.c | 39 ++++++++++++++++++++++++++++-----------
> drivers/mmc/host/sdhci.h | 2 ++
> 2 files changed, 30 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> index f64e766..1ca3871 100644
> --- a/drivers/mmc/host/sdhci.c
> +++ b/drivers/mmc/host/sdhci.c
> @@ -1033,6 +1033,33 @@ static inline bool sdhci_auto_cmd12(struct sdhci_host *host,
> !mrq->cap_cmd_during_tfr;
> }
>
> +static inline void sdhci_auto_cmd_enable(struct sdhci_host *host,
> + struct mmc_command *cmd,
> + u16 *mode)
> +{
> + /*
> + * In case of Version 4.10 or later, use of 'Auto CMD Auto
> + * Select' is recommended rather than use of 'Auto CMD12
> + * Enable' or 'Auto CMD23 Enable'.
> + */
> + if (host->version >= SDHCI_SPEC_410) {
> + *mode |= SDHCI_TRNS_AUTO_SEL;
The rules for selecting auto commands still need to be applied. In effect:
if (sdhci_auto_cmd12(host, cmd->mrq) &&
(cmd->opcode != SD_IO_RW_EXTENDED)) {
*mode |= SDHCI_TRNS_AUTO_SEL;
} else if (cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
*mode |= SDHCI_TRNS_AUTO_SEL;
sdhci_writel(host, cmd->mrq->sbc->arg, SDHCI_ARGUMENT2);
}
Also the selection of Host Control 2 register CMD23 Enable should be done by
SDHCI (if supported by the card) not the Spreadtrum driver.
> + return;
> + }
> +
> + /*
> + * If we are sending CMD23, CMD12 never gets sent
> + * on successful completion (so no Auto-CMD12).
> + */
> + if (sdhci_auto_cmd12(host, cmd->mrq) &&
> + (cmd->opcode != SD_IO_RW_EXTENDED)) {
> + *mode |= SDHCI_TRNS_AUTO_CMD12;
> + } else if (cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
> + *mode |= SDHCI_TRNS_AUTO_CMD23;
> + sdhci_writel(host, cmd->mrq->sbc->arg, SDHCI_ARGUMENT2);
> + }
> +}
> +
> static void sdhci_set_transfer_mode(struct sdhci_host *host,
> struct mmc_command *cmd)
> {
> @@ -1059,17 +1086,7 @@ static void sdhci_set_transfer_mode(struct sdhci_host *host,
>
> if (mmc_op_multi(cmd->opcode) || data->blocks > 1) {
> mode = SDHCI_TRNS_BLK_CNT_EN | SDHCI_TRNS_MULTI;
> - /*
> - * If we are sending CMD23, CMD12 never gets sent
> - * on successful completion (so no Auto-CMD12).
> - */
> - if (sdhci_auto_cmd12(host, cmd->mrq) &&
> - (cmd->opcode != SD_IO_RW_EXTENDED))
> - mode |= SDHCI_TRNS_AUTO_CMD12;
> - else if (cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
> - mode |= SDHCI_TRNS_AUTO_CMD23;
> - sdhci_writel(host, cmd->mrq->sbc->arg, SDHCI_ARGUMENT2);
> - }
> + sdhci_auto_cmd_enable(host, cmd, &mode);
> }
>
> if (data->flags & MMC_DATA_READ)
> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> index 889e48b..8263ac6 100644
> --- a/drivers/mmc/host/sdhci.h
> +++ b/drivers/mmc/host/sdhci.h
> @@ -42,6 +42,7 @@
> #define SDHCI_TRNS_BLK_CNT_EN 0x02
> #define SDHCI_TRNS_AUTO_CMD12 0x04
> #define SDHCI_TRNS_AUTO_CMD23 0x08
> +#define SDHCI_TRNS_AUTO_SEL 0x0C
> #define SDHCI_TRNS_READ 0x10
> #define SDHCI_TRNS_MULTI 0x20
>
> @@ -185,6 +186,7 @@
> #define SDHCI_CTRL_DRV_TYPE_D 0x0030
> #define SDHCI_CTRL_EXEC_TUNING 0x0040
> #define SDHCI_CTRL_TUNED_CLK 0x0080
> +#define SDHCI_CMD23_ENABLE 0x0800
> #define SDHCI_CTRL_V4_MODE 0x1000
> #define SDHCI_CTRL_64BIT_ADDR 0x2000
> #define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
