The following changes are quite small, therefore I combined them in
one patch.
- ret doesn't need to be initialized with 0
- use standard !clk_rate notation to check for a zero value
- If clk_rate is zero we return here. Therefore all further checks
in this function for clk_rate != 0 are not needed.
- switch from dev_warn to dev_err if the clock can't be set
- If due to clock source and available divider values the requested
frequency isn't matched exactly (always the case if requested
frequency is 52 MHz), then just print the differing values as
debug message and not as warning.
- Also remove ret from the message as it is always 0.
- In the case of actual frequency not exactly matching the requested
one set mmc->actual_clock to the requested frequency.
So far mmc->actual_clock wasn't set at all in this case.
Signed-off-by: Heiner Kallweit <hkallweit1@xxxxxxxxx>
---
drivers/mmc/host/meson-gx-mmc.c | 36 +++++++++++++++++++-----------------
1 file changed, 19 insertions(+), 17 deletions(-)
diff --git a/drivers/mmc/host/meson-gx-mmc.c b/drivers/mmc/host/meson-gx-mmc.c
index 38edc60d..529a4f22 100644
--- a/drivers/mmc/host/meson-gx-mmc.c
+++ b/drivers/mmc/host/meson-gx-mmc.c
@@ -179,7 +179,7 @@ struct sd_emmc_desc {
static int meson_mmc_clk_set(struct meson_host *host, unsigned long clk_rate)
{
struct mmc_host *mmc = host->mmc;
- int ret = 0;
+ int ret;
u32 cfg;
if (clk_rate) {
@@ -202,29 +202,31 @@ static int meson_mmc_clk_set(struct meson_host *host, unsigned long clk_rate)
dev_dbg(host->dev, "change clock rate %u -> %lu\n",
mmc->actual_clock, clk_rate);
- if (clk_rate == 0) {
+ if (!clk_rate) {
mmc->actual_clock = 0;
return 0;
}
ret = clk_set_rate(host->cfg_div_clk, clk_rate);
- if (ret)
- dev_warn(host->dev, "Unable to set cfg_div_clk to %lu. ret=%d\n",
- clk_rate, ret);
- else if (clk_rate && clk_rate != clk_get_rate(host->cfg_div_clk))
- dev_warn(host->dev, "divider requested rate %lu != actual rate %lu: ret=%d\n",
- clk_rate, clk_get_rate(host->cfg_div_clk), ret);
- else
- mmc->actual_clock = clk_rate;
-
- /* (re)start clock, if non-zero */
- if (!ret && clk_rate) {
- cfg = readl(host->regs + SD_EMMC_CFG);
- cfg &= ~CFG_STOP_CLOCK;
- writel(cfg, host->regs + SD_EMMC_CFG);
+ if (ret) {
+ dev_err(host->dev, "Unable to set cfg_div_clk to %lu. ret=%d\n",
+ clk_rate, ret);
+ return ret;
}
- return ret;
+ if (clk_rate != clk_get_rate(host->cfg_div_clk))
+ dev_dbg(host->dev,
+ "divider requested rate %lu != actual rate %lu\n",
+ clk_rate, clk_get_rate(host->cfg_div_clk));
+
+ mmc->actual_clock = clk_rate;
+
+ /* (re)start clock */
+ cfg = readl(host->regs + SD_EMMC_CFG);
+ cfg &= ~CFG_STOP_CLOCK;
+ writel(cfg, host->regs + SD_EMMC_CFG);
+
+ return 0;
}
/*
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
