Hello Ulf and Adrian, This patch is going to support enhanced strobe function for emmc version 5.1+ introduced by JEDEC recently. Enchanced strobe is a optional function, so we add a new cap* for drivers to decide whether to use it. When introduing hs400 mode, JEDEC asks controllers to use data strobe line to latch the data from emmc devives. But for cmd-reponse, not mentioned yet. Since emmc version 5.1 published, JEDEC adds enhanced strobe function to deal with cmd-response the same way as data-read. This feature is optional. >From the spec(section 6.6.2.3), the standard scenario to select HS400 enhanced strobe mode illustrated like this: (1) set HS_TIMIMG (Highspeed) (2) Host change freq to <= 52Mhz (3) set the bus width to Enhanced strobe and DDR8Bit(CMD6), EXT_CSD[183] = 0x86 instead of 0x80 (4) set HS_TIMING to 0x3 (HS400) (5) Host change freq to <= 200Mhz (6) Host select HS400 enhanced strobe complete I can't find a upstreamed controller claimed to support it, as well as the mmc stack. But my "arasan,sdhci-5.1" actually supports this function. So I decide to work for this part. By looking into the SDHCI spec, I find there isn't any registers to enable the enhanced strobe function. But from my "arasan,sdhci-5.1" databook, it describes a register called VENDOR_REGISTER(0x78) to trigger this mode. So I guess other sdhci variant drivers may also need s vendor specific register to deal with it. If we are sure that our controller supports enhanced strobe mode, just add mmc-hs400-enhanced-strobe in DT. Once emmc devices claims to support this mode, we enable it automatically. Of course, other sdhci*/non-sdhci drivers should implement/overwrite the prepare_enhanced_strobe by themselves. I believe all of the platforms which need to support this mode should do some basic preparation for their controllers. Currently I just limit the callback within ths scope of arasan,sdhci-5.1, but I prone to believe arasan will use VENDOR_REGISTER to tirgger this mode from now on because I do believe vendor will consider the registers' compatibility. With this patchset applied, we can successfully run in HS400 enhanced strobe mode on RK3399 platform with Samsung eMMC KLMBG2JENB-B041(v5.1, 16GB). mmc1: new HS400 Enhanced strobe MMC card at address 0001 mmcblk0: mmc1:0001 AJNB4R 14.6 GiB mmcblk0boot0: mmc1:0001 AJNB4R partition 1 4.00 MiB mmcblk0boot1: mmc1:0001 AJNB4R partition 2 4.00 MiB mmcblk0rpmb: mmc1:0001 AJNB4R partition 3 4.00 MiB Also I check this patchset with removing some caps to make sure all the init sequences for hs400/hs200/DDR52/HighSpeed is correct. Changes in v3: - remove helper function and shorten cap2 to MMC_CAP2_HS400_ES - rename callback to hs400_enhanced_strobe and make it return void - add enhanced_strobe in mmc_ios and pass it to hs400_enhanced_strobe - disable host's enhanced strobe in mmc_set_initial_state - remove bus checking after switching hs400es - add new function for hs400es timing selection - fix wrong judgement of mmc_card_hs400es Changes in v2: - switch to HS400ES from Highspeed mode directly Shawn Lin (5): Documentation: mmc: add mmc-hs400-enhanced-strobe mmc: core: add mmc-hs400-enhanced-strobe support mmc: core: implement enhanced strobe support mmc: debugfs: add HS400 enhanced strobe description mmc: sdhci-of-arasan: implement enhanced strobe callback Documentation/devicetree/bindings/mmc/mmc.txt | 1 + drivers/mmc/core/bus.c | 3 +- drivers/mmc/core/core.c | 8 +++ drivers/mmc/core/debugfs.c | 4 +- drivers/mmc/core/host.c | 2 + drivers/mmc/core/mmc.c | 79 ++++++++++++++++++++++++++- drivers/mmc/host/sdhci-of-arasan.c | 20 +++++++ include/linux/mmc/card.h | 1 + include/linux/mmc/host.h | 12 ++++ include/linux/mmc/mmc.h | 3 + 10 files changed, 129 insertions(+), 4 deletions(-) -- 2.3.7 -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
