Hi, On 28.03.2016 15:50, Marek Vasut wrote: > On 03/28/2016 12:34 PM, Jaehoon Chung wrote: >> Hi, > > Hi, > > [...] > >>>>>>>>> That said, I would rather prefer to see "snps,dw-mshc" prefix on description >>>>>>>>> of an MMC controller found on SoCFPGA series, "altr,socfpga-dw-mshc" seems >>>>>>>>> to be redundant. >> >> Yes..it's redundant..i should be combined to "snps,dw-mshc". > > Should the compat string be > compatible = "altr,socfpga-dw-mshc", "snps,dw-mshc"; > or just > compatible = "snps,dw-mshc"; > ? > > I am under the impression that a soc-specific identifier in addition to > a generic one (used by the driver compat table) is a good idea, because > it can help discerning the IP block from a generic one if needed at some > future point in time. It will also not break the DT for systems > which may depend on the non-generic compat, like *BSDs and such. > > What do you think ? (btw this is very much my question in this thread) IMO just 'compatible = "snps,dw-mshc"' is good enough, if it completely describes the IP block on SoCFGPA --- and from what I get it is the case. You can add a SoC-specific compatible if it is needed later on, and to my taste only if SoC specific features can not be covered by properties. The same sole "snps,dw-mshc" compatible is specified for NXP LPC18xx/43xx, ZTE ZX and HiSilicon ARM SoCs. Another similar example is ARM PrimeCell PLxxx IP blocks, as far as I know there is no SoC-specific compatibles/aliases for PrimeCell IP blocks. Rob, please correct me. >>>>>>>> According to drivers/mmc/host/dw_mmc-pltfm.c , the Altera SoCFPGA one >>>>>>>> "altr,socfpga-dw-mshc" and also Imagination Technology Pistacio one >>>>>>>> "img,pistachio-dw-mshc" need specialty bit (SDMMC_CMD_USE_HOLD_REG), >>>>>>>> while the stock one "snps,dw-mshc" does not. I am not sure if the ARC >>>>>>>> one needs it as well, but most likely yes. >>>>>>>> >>>>>>>> I wonder if that bit is needed on some particular version of the DWMMC >>>>>>>> core. In that case, should we have "snps,dw-mshc" and "snps,dw-mshc-vN" >>>>>>>> binding ? Or should we use DT property to discern the need for this bit ? >>>>>>>> >>>>>>> That's the most common way to take into account peculiarities, add >>>>>>> a property and handle it from the driver. >>>>>> And by "that" you mean which of those two I listed , the >>>>>> "snps,dw-mshc-vN" or adding new DT prop ? >>>>>> >>>>> I meant to add a new property, not a new compatible, but that's just >>>>> my experience. >>>>> >>>>> Let me say it __might__ happen that a particular change you need is >>>>> specific to a particular version of the DWMMC IP (query Synopsys >>>>> by the way), but more probably it might be e.g. the same IP version with >>>>> a different reduced or extended configuration or a minor fix/improvement >>>>> to the IP block without resulting version number bump. >>>>> >>>>> For example I don't remember that errata fixes in IP blocks result in >>>>> a new compatible, instead there are quite common optional "quirk" >>>>> properties for broken IPs -- e.g. check bindings/usb/dwc3.txt :) >>>> Right, this very much matches how I see it as well. Thanks for confirming. >>>> >>>> Alexey, can you tell us if the requirement for setting >>>> SDMMC_CMD_USE_HOLD_REG came with some new revision of the core or >>>> disappeared with some revision OR if this is some configuration >>>> option of the core during synthesis ? >>> >>> Sorry for not following that discussion during my weekend but I'll try >>> to address all questions now. >> >> SDMMC_CMD_USE_HOLD_REG didn't come with new revision..It's using continuously. >> But it's difficult to use the generic feature..because it's considered the below things. >> >> If Card is SDR50/SDR104/DDR50 mode.. >> 1) and phase shift of cclk_in_drv is 0 then SDMMC_CMD_USE_HOLD_REG bit is set to 0, >> 2) and phase shift of cclk_in_drv > 0 then SDMMC_CMD_USE_HOLD_REG bit is set to 1, >> If Card is SDR12/SDR25 mode, then this bit is set to 1. >> >> We need to check phase shift scheme..but as i knew, each SoC have been implemented differently for phase shift. >> (Phase shift have dependency to SoC.) >> >> And it have to check HCON register..there is IMPLEMENT_HOLD_REG(bit[22]). >> (It described whether IP have hold register or not) >> >> I didn't read this thread entirely. >> I'm not sure what you have discussed..but my understanding is right..i recommend to use "snps,dw-mshc" for ARC compat string. >> Otherwise it need to add "dw_mmc-<SoC>.c". dw_mmc-pltfm.c should provide the basic dw-mmc controller functionality. >> >> After read this thread entirely, i will check more detailed what you discussed. >> If i missed something, let me know, plz. > > Thanks for the clarification, linux-next indeed contains changes which > make snps,dw-mshc and altr,socfpga-dw-mshc equal. > >> Best Regards, >> Jaehoon Chung >> >>> >>> DW Mobile Storage databook says: >>> --------------------->8----------------------- >>> To meet the relatively high Input Hold Time requirement for SDR12, SDR25, >>> and other MMC speed modes, you should program bit[29]use_hold_Reg of the >>> CMD register to 1'b1. >>> --------------------->8----------------------- >>> >>> So I'd say this specific setting has nothing to do with a particular IP block >>> but instead it is related to card's mode of operation. More precisely bus clock. >>> SDR12 stands for 12.5 MByte/s, SDR25 stands for 25 MByte/s. I.e. we probably need >>> so set that bit just for certain cases and regardless board that uses DW MMC. >>> >>> I'm adding DW MMC maintainer as well as linux-mmc mailing list so people who >>> understands that stuff better may comment here as well. >>> >>> -Alexey-- >>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in >>> the body of a message to majordomo@xxxxxxxxxxxxxxx >>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>> >>> >> > > -- With best wishes, Vladimir -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
