On Fri, July 04, 2014, Seungwon Jeon wrote:
> On Tue, July 01, 2014. Yuvaraj Kumar wrote:
> > On Fri, Jun 27, 2014 at 4:48 PM, Seungwon Jeon <tgih.jun@xxxxxxxxxxx> wrote:
> > > Hi Yuvaraj,
> > >
> > > On Fri, June 27, 2014, Yuvaraj Kumar wrote:
> > >> On Thu, Jun 26, 2014 at 10:20 PM, Doug Anderson <dianders@xxxxxxxxxxxx> wrote:
> > >> > Seungwon,
> > >> >
> > >> > On Thu, Jun 26, 2014 at 3:41 AM, Seungwon Jeon <tgih.jun@xxxxxxxxxxx> wrote:
> > >> >> On Thu, June 26, 2014, Doug Anderson wrote:
> > >> >>> Seungwon,
> > >> >>>
> > >> >>> On Wed, Jun 25, 2014 at 6:08 AM, Seungwon Jeon <tgih.jun@xxxxxxxxxxx> wrote:
> > >> >>> > On Mon, June 23, 2014, Yuvaraj Kumar C D wrote:
> > >> >>> >> Subject: [PATCH 3/3] mmc: dw_mmc: Support voltage changes
> > >> >>> >>
> > >> >>> >> From: Doug Anderson <dianders@xxxxxxxxxxxx>
> > >> >>> >>
> > >> >>> >> For UHS cards we need the ability to switch voltages from 3.3V to
> > >> >>> >> 1.8V. Add support to the dw_mmc driver to handle this. Note that
> > >> >>> >> dw_mmc needs a little bit of extra code since the interface needs a
> > >> >>> >> special bit programmed to the CMD register while CMD11 is progressing.
> > >> >>> >> This means adding a few extra states to the state machine to track.
> > >> >>> >
> > >> >>> > Overall new additional states makes it complicated.
> > >> >>> > Can we do that in other way?
> > >> >>>
> > >> >>> That was the best I was able to figure out when I thought this
> > >> >>> through. If you have ideas for doing it another way I'd imagine that
> > >> >>> Yuvaraj would be happy to take your feedback.
> > >> >> Let's clean up SDMMC_CMD_VOLT_SWITCH.
> > >> >> In turn, we may remove state-handling simply.
> > >> >>
> > >> >>>
> > >> >>>
> > >> >>> >> Signed-off-by: Doug Anderson <dianders@xxxxxxxxxxxx>
> > >> >>> >> Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@xxxxxxxxxxx>
> > >> >>> >>
> > >> >>> >> ---
> > >> >>> >> drivers/mmc/host/dw_mmc.c | 145 +++++++++++++++++++++++++++++++++++++++++---
> > >> >>> >> drivers/mmc/host/dw_mmc.h | 5 +-
> > >> >>> >> include/linux/mmc/dw_mmc.h | 2 +
> > >> >>> >> 3 files changed, 142 insertions(+), 10 deletions(-)
> > >> >>> >>
> > >> >>> >> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> > >> >>> >> index e034bce..38eb548 100644
> > >> >>> >> --- a/drivers/mmc/host/dw_mmc.c
> > >> >>> >> +++ b/drivers/mmc/host/dw_mmc.c
> > >> >>> >> @@ -29,6 +29,7 @@
> > >> >>> >> #include <linux/irq.h>
> > >> >>> >> #include <linux/mmc/host.h>
> > >> >>> >> #include <linux/mmc/mmc.h>
> > >> >>> >> +#include <linux/mmc/sd.h>
> > >> >>> >> #include <linux/mmc/sdio.h>
> > >> >>> >> #include <linux/mmc/dw_mmc.h>
> > >> >>> >> #include <linux/bitops.h>
> > >> >>> >> @@ -235,10 +236,13 @@ err:
> > >> >>> >> }
> > >> >>> >> #endif /* defined(CONFIG_DEBUG_FS) */
> > >> >>> >>
> > >> >>> >> +static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg);
> > >> >>> >> +
> > >> >>> >> static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
> > >> >>> >> {
> > >> >>> >> struct mmc_data *data;
> > >> >>> >> struct dw_mci_slot *slot = mmc_priv(mmc);
> > >> >>> >> + struct dw_mci *host = slot->host;
> > >> >>> >> const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
> > >> >>> >> u32 cmdr;
> > >> >>> >> cmd->error = -EINPROGRESS;
> > >> >>> >> @@ -254,6 +258,32 @@ static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct
> > mmc_command
> > >> >>> *cmd)
> > >> >>> >> else if (cmd->opcode != MMC_SEND_STATUS && cmd->data)
> > >> >>> >> cmdr |= SDMMC_CMD_PRV_DAT_WAIT;
> > >> >>> >>
> > >> >>> >> + if (cmd->opcode == SD_SWITCH_VOLTAGE) {
> > >> >>> >> + u32 clk_en_a;
> > >> >>> >> +
> > >> >>> >> + /* Special bit makes CMD11 not die */
> > >> >>> >> + cmdr |= SDMMC_CMD_VOLT_SWITCH;
> > >> >>> >> +
> > >> >>> >> + /* Change state to continue to handle CMD11 weirdness */
> > >> >>> >> + WARN_ON(slot->host->state != STATE_SENDING_CMD);
> > >> >>> >> + slot->host->state = STATE_SENDING_CMD11;
> > >> >>> >> +
> > >> >>> >> + /*
> > >> >>> >> + * We need to disable clock stop while doing voltage switch
> > >> >>> >> + * according to 7.4.1.2 Voltage Switch Normal Scenario.
> > >> >>> >> + *
> > >> >>> >> + * It's assumed that by the next time the CLKENA is updated
> > >> >>> >> + * (when we set the clock next) that the voltage change will
> > >> >>> >> + * be over, so we don't bother setting any bits to synchronize
> > >> >>> >> + * with dw_mci_setup_bus().
> > >> >>> >> + */
> > >> >>> >> + clk_en_a = mci_readl(host, CLKENA);
> > >> >>> >> + clk_en_a &= ~(SDMMC_CLKEN_LOW_PWR << slot->id);
> > >> >>> >> + mci_writel(host, CLKENA, clk_en_a);
> > >> >>> >> + mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
> > >> >>> >> + SDMMC_CMD_PRV_DAT_WAIT, 0);
> > >> >>> > dw_mci_disable_low_power() can be used here.
> > >> >>>
> > >> >>> Ah. I guess we don't have that locally anymore. Locally we have variants on:
> > >> >> I'm checking on cjb/mmc branch.
> > >> >>
> > >> >>> * https://patchwork.kernel.org/patch/3070311/
> > >> >>> * https://patchwork.kernel.org/patch/3070251/
> > >> >>> * https://patchwork.kernel.org/patch/3070221/
> > >> >>>
> > >> >>> ...which removed that function. ...but I guess upstream never picked
> > >> >>> up those patches, huh? Looking back it looks like you had some
> > >> >>> feedback and it needed another spin but somehow fell off my plate. :(
> > >> >>>
> > >> >>> Maybe this is something Yuvaraj would like to pick up?
> > >> >> It's long ago. I remember that there is no progress since my last comment.
> > >> >> In case of patch "3070221", I want to pick up for next Kernel.
> > >> >
> > >> > Sounds like Yuvaraj has agreed to look at addressing your comments. Thanks!
> > >> >
> > >> >
> > >> >>> >> + }
> > >> >>> >> +
> > >> >>> >> if (cmd->flags & MMC_RSP_PRESENT) {
> > >> >>> >> /* We expect a response, so set this bit */
> > >> >>> >> cmdr |= SDMMC_CMD_RESP_EXP;
> > >> >>> >> @@ -776,11 +806,15 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool
> > force_clkinit)
> > >> >>> >> unsigned int clock = slot->clock;
> > >> >>> >> u32 div;
> > >> >>> >> u32 clk_en_a;
> > >> >>> >> + u32 sdmmc_cmd_bits = SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT;
> > >> >>> >> +
> > >> >>> >> + /* We must continue to set bit 28 in CMD until the change is complete */
> > >> >>> >> + if (host->state == STATE_WAITING_CMD11_DONE)
> > >> >>> >> + sdmmc_cmd_bits |= SDMMC_CMD_VOLT_SWITCH;
> > >> >>> > I didn't get the reason SDMMC_CMD_VOLT_SWITCH is needed during clock update(enable/disable)
> > >> >>> > Can you explain it in details?
> > >> >>>
> > >> >>> Simply put: if I didn't do this then the system hung during voltage
> > >> >>> switch. It was not documented in the version of the IP manual that I
> > >> >>> had access to and it took me a bunch of digging / trial and error to
> > >> >>> figure this out. Whatever this bit does internally it's important to
> > >> >>> set it while the voltage change is happening. Note that this need was
> > >> >>> the whole reason for adding the extra state to the state machine.
> > >> >>>
> > >> >>> Perhaps Yuvaraj can try without it and I'd assume he'll report the
> > >> >>> same freeze.
> > >> >> Clarify the necessity of SDMMC_CMD_VOLT_SWITCH.
> > >> >> As far as I experience, we didn't apply this bit for several projects.
> > >> >
> > >> > I just tried this locally on our ChromeOS 3.8 kernel (which has quite
> > >> > a few backports and matches dw_mmc upstream pretty closely). When I
> > >> > take out "sdmmc_cmd_bits |= SDMMC_CMD_VOLT_SWITCH" and bootup it fails
> > >> > to bringup WiFi chip. It prints messages like:
> > >> >
> > >> > [ 4.400842] mmc_host mmc1: Timeout sending command (cmd 0x202000
> > >> > arg 0x0 status 0x80202000)
> > >> >
> > >> > I will let Yuvaraj comment about his testing too.
> > >> To make it simple and verify, i have just enabled eMMC and SD channels
> > >> on 3.16-rc1 and tested.
> > >> Without "sdmmc_cmd_bits |= SDMMC_CMD_VOLT_SWITCH" bootup fails.
> > >> [ 3.015971] mmc_host mmc1: Timeout sending command (cmd 0x202000
> > >> arg 0x0 status 0x80202000)
> > >> [ 3.530974] mmc_host mmc1: Timeout sending command (cmd 0x202000
> > >> arg 0x0 status 0x80202000)
> > > Thank you for test.
> > > Hmm, it failed during clock update, right?.
> > > Can you check HLE interrupt at this time?
> > > I'll investigate for this.
> > Yes, it failed during clock update.I am dumping the register contents
> > just before the dev_err statement.I can observe that 1st timeout does
> > not have HLE interrupt.But once we set bit 0 of UHS_REG subsequent
> > timeout's have HLE bit set.I am attaching the complete log.
>
> Before disabling the clocks, we ensure that the card is not busy.(It's from Synopsys's databook)
> I guess SDMMC_CMD_VOLT_SWITCH flag seems to affect to avoid this limitation if you have no problem.
> But, I met the following log with HEL when I apply and test this patch .
>
> "mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)"
> I need to look into it more deeply.
I confirmed that SDMMC_CMD_VOLT_SWITCH is needed during clock-off/on in voltage switching sequence
even though there is no description for this in Synopsys's databook.
And the above-mentioned message("mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x80202000)")
is happened on mmc_power_cycle(), which should be done because of busy status of DAT[3:0].
It indicates clock-off/on sequence fails when executing mmc_power_cycle().
>
> > >
> > >> >
> > >> >
> > >> >>> >> +static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
> > >> >>> >> +{
> > >> >>> >> + struct dw_mci_slot *slot = mmc_priv(mmc);
> > >> >>> >> + struct dw_mci *host = slot->host;
> > >> >>> >> + u32 uhs;
> > >> >>> >> + u32 v18 = SDMMC_UHS_18V << slot->id;
> > >> >>> >> + int min_uv, max_uv;
> > >> >>> >> + int ret;
> > >> >>> >> +
> > >> >>> >> + /*
> > >> >>> >> + * Program the voltage. Note that some instances of dw_mmc may use
> > >> >>> >> + * the UHS_REG for this. For other instances (like exynos) the UHS_REG
> > >> >>> >> + * does no harm but you need to set the regulator directly. Try both.
> > >> >>> >> + */
> > >> >>> >> + uhs = mci_readl(host, UHS_REG);
> > >> >>> >> + if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
> > >> >>> >> + min_uv = 2700000;
> > >> >>> >> + max_uv = 3600000;
> > >> >>> >> + uhs &= ~v18;
> > >> >>> >> + } else {
> > >> >>> >> + min_uv = 1700000;
> > >> >>> >> + max_uv = 1950000;
> > >> >>> >> + uhs |= v18;
> > >> >>> >> + }
> > >> >>> >> + if (!IS_ERR(mmc->supply.vqmmc)) {
> > >> >>> >> + ret = regulator_set_voltage(mmc->supply.vqmmc, min_uv, max_uv);
> > >> >>> >> +
> > >> >>> >> + /*
> > >> >>> >> + * Only complain if regulator claims that it's not in the 1.8V
> > >> >>> >> + * range. This avoids a bunch of errors in the case that
> > >> >>> >> + * we've got a fixed 1.8V regulator but the core SD code still
> > >> >>> >> + * thinks it ought to try to switch to 3.3 and then back to 1.8
> > >> >>> >> + */
> > >> >>> >> + if (ret) {
> > >> >>> > I think if ret is error, printing message and returning error is good.
> > >> >>> > Currently, just returning '0' though it fails.
> > >> >> Any feedback?
> > >> >
> > >> > Whoops, right. I think you're right that in the case it warns it
> > >> > should also return the error code. In the case it doesn't warn it
> > >> > shouldn't. Also: possibly we should use a trick like the mmc core
> > >> > does and use "regulator_count_voltages" to figure out if we're going
> > >> > to be able to switch voltages...
> > >> >
> > >> >>> > Artificially adding SDMMC_INT_CMD_DONE to pending is needed to complete cmd handling?
> > >> >>> > Is there any reason?
> > >> >>>
> > >> >>> I don't remember this for sure since I wrote this a long time ago.
> > >> >>> Maybe it's not needed? I may have just been modeling on other
> > >> >>> interrupts.
> > >> >> If there is no specific reason, please remove it.
> > >> >
> > >> > OK, we'll see how Yuvaraj's testing goes without it. My incredibly
> > >> > brief testing in our local Chrome OS 3.8 tree shows that the WiFi is
> > >> > not detected properly if I comment out the line:
> > >> > dw_mci_cmd_interrupt(host,
> > >> > pending | SDMMC_INT_CMD_DONE);
> > >> >
> > >> > It may be sufficient to simply schedule the tasklet or to do some
> > >> > other subset of dw_mci_cmd_interrupt(). Yuvaraj can confirm on the
> > >> > latest kernel and also investigate further.
> > > How about completing CMD without SDMMC_INT_CMD_DONE?
> > Without this tuning fails.
> > [ 2.525284] mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot
> > req 200000000Hz, actual 200000000HZ div = 0)
> > [ 198.556573] random: nonblocking pool is initialized
> > [ 240.226044] INFO: task kworker/u8:0:6 blocked for more than 120 seconds.
> > [ 240.231276] Not tainted 3.16.0-rc1-00010-g2f7a756-dirty #55
> > [ 240.237359] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs"
> > disables this message.
> > [ 240.245150] kworker/u8:0 D c03a58a0 0 6 2 0x00000000
> > [ 240.251487] Workqueue: kmmcd mmc_rescan
> > [ 240.255297] [<c03a58a0>] (__schedule) from [<c03a5330>]
> > (schedule_timeout+0x130/0x170)
> > [ 240.263201] [<c03a5330>] (schedule_timeout) from [<c03a6540>]
> > (wait_for_common+0xbc/0x14c)
> > [ 240.271441] [<c03a6540>] (wait_for_common) from [<c02ca6e4>]
> > (mmc_wait_for_req_done+0x6c/0xf0)
> > [ 240.280031] [<c02ca6e4>] (mmc_wait_for_req_done) from [<c02e3f10>]
> > (dw_mci_exynos_execute_tuning+0x1d4/0x2c4)
> > [ 240.289919] [<c02e3f10>] (dw_mci_exynos_execute_tuning) from
> > [<c02e0198>] (dw_mci_execute_tuning+0x54/0xb4)
> > [ 240.299635] [<c02e0198>] (dw_mci_execute_tuning) from [<c02cf47c>]
> > (mmc_init_card+0xeec/0x14ac)
> > [ 240.308309] [<c02cf47c>] (mmc_init_card) from [<c02cfc34>]
> > (mmc_attach_mmc+0x8c/0x160)
> > [ 240.316202] [<c02cfc34>] (mmc_attach_mmc) from [<c02cca0c>]
> > (mmc_rescan+0x2b0/0x308)
> > [ 240.323924] [<c02cca0c>] (mmc_rescan) from [<c0032f60>]
> > (process_one_work+0xf8/0x364)
> > [ 240.331732] [<c0032f60>] (process_one_work) from [<c0033800>]
> > (worker_thread+0x50/0x5a0)
> > [ 240.339799] [<c0033800>] (worker_thread) from [<c0038e7c>]
> > (kthread+0xd8/0xf0)
> > [ 240.346999] [<c0038e7c>] (kthread) from [<c000e438>]
> > (ret_from_fork+0x14/0x3c)
>
> Thank you for test.
> I want to clear it why CMD_DONE is related to tuning.
In my case, SDMMC_INT_CMD_DONE doesn't affect.
And do you check VOLT_SWITCH interrupt occurs twice during voltage-switching.
For last one, if-statement in dw_mci_interrupt() disturbs clearing interrupt.
if ((host->state == STATE_SENDING_CMD11) &&
In addition, I suggest adding another flag instead of using host's state.
Can you consider it?
Thanks,
Seungwon Jeon
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
