On Thu, Jun 26, 2014 at 07:23:30AM +0100, Vincent Yang wrote:
> This patch adds new host controller driver for
> Fujitsu SDHCI controller f_sdh30.
>
> Signed-off-by: Vincent Yang <Vincent.Yang@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/mmc/sdhci-fujitsu.txt | 35 +++
> drivers/mmc/host/Kconfig | 7 +
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/sdhci_f_sdh30.c | 346 +++++++++++++++++++++
> drivers/mmc/host/sdhci_f_sdh30.h | 40 +++
> 5 files changed, 429 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> create mode 100644 drivers/mmc/host/sdhci_f_sdh30.c
> create mode 100644 drivers/mmc/host/sdhci_f_sdh30.h
>
> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> new file mode 100644
> index 0000000..40add438
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/sdhci-fujitsu.txt
> @@ -0,0 +1,35 @@
> +* Fujitsu SDHCI controller
> +
> +This file documents differences between the core properties in mmc.txt
> +and the properties used by the sdhci_f_sdh30 driver.
> +
> +Required properties:
> +- compatible: "fujitsu,f_sdh30"
Please use '-' rather than '_' in compatible strings.
This seems to be the name of the driver. What is the precise name of the
IP block?
> +- voltage-ranges : two cells are required, first cell specifies minimum
> + slot voltage (mV), second cell specifies maximum slot voltage (mV).
> + Several ranges could be specified.
Describe this as a list of pairs, it's confusing otherwise.
I'm not sure I follow what having multiple pairs implies.
> +Optional properties:
> +- gpios: This is one optional gpio for controlling a power mux which
> + switches between two power supplies. 3.3V is selected when gpio is high,
> + and 1.8V is selected when gpio is low. This voltage is used for signal
> + level.
Give this a more descriptive name, like power-mux-gpios. That will match
up with the style of cd-gpios and wp-gpios.
> +- clocks: Must contain an entry for each entry in clock-names. It is a
> + list of phandles and clock-specifier pairs.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Should contain the following two entries:
> + "sd_sd4clk" - clock primarily used for tuning process
> + "sd_bclk" - base clock for sdhci controller
> +
> +Example:
> +
> + sdhci1: sdio@36600000 {
> + compatible = "fujitsu,f_sdh30";
> + reg = <0 0x36600000 0x1000>;
> + interrupts = <0 172 0x4>,
> + <0 173 0x4>;
> + voltage-ranges = <1800 1800 3300 3300>;
Place brackets around each pair to make this clearer:
voltage-ranges = <1800 1800>, <3300 3300>;
[...]
> + if (!of_property_read_u32(pdev->dev.of_node, "vendor-hs200",
> + &priv->vendor_hs200))
> + dev_info(dev, "Applying vendor-hs200 setting\n");
> + else
> + priv->vendor_hs200 = 0;
This wasn't in the binding document, and a grep for "vendor-hs200" in a
v3.16-rc2 tree found me nothing.
Please document this.
> +
> + if (!of_property_read_u32(pdev->dev.of_node, "bus-width", &bus_width)) {
> + if (bus_width == 8) {
> + dev_info(dev, "Applying 8 bit bus width\n");
> + host->mmc->caps |= MMC_CAP_8_BIT_DATA;
> + }
> + }
What if bus-width is not 8, or is not present?
> +
> + ret = mmc_of_parse_voltage(pdev->dev.of_node, &host->ocr_mask);
> + if (ret) {
> + dev_err(dev, "%s: parse voltage error\n", __func__);
> + goto err_voltage;
> + }
> +
> + host->hw_name = DRIVER_NAME;
> + host->ops = &sdhci_f_sdh30_ops;
> + host->irq = irq;
> +
> + host->ioaddr = of_iomap(pdev->dev.of_node, 0);
> + if (!host->ioaddr) {
> + dev_err(dev, "%s: failed to remap registers\n", __func__);
> + ret = -ENXIO;
> + goto err_remap;
> + }
> +
> + priv->clk_sd4 = of_clk_get(pdev->dev.of_node, 0);
> + if (!IS_ERR(priv->clk_sd4)) {
> + ret = clk_prepare_enable(priv->clk_sd4);
> + if (ret < 0) {
> + dev_err(dev, "Failed to enable sd4 clock: %d\n", ret);
> + goto err_clk1;
> + }
> + }
> + priv->clk_b = of_clk_get(pdev->dev.of_node, 1);
> + if (!IS_ERR(priv->clk_b)) {
> + ret = clk_prepare_enable(priv->clk_b);
> + if (ret < 0) {
> + dev_err(dev, "Failed to enable clk_b clock: %d\n", ret);
> + goto err_clk2;
> + }
> + }
Given you gave these names, get these by name rather than index. It's
less surprising and more flexible.
Thanks,
Mark.
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
