Dear, All.
Do you have any other comment for this patchset?
I have tested with exynos4/5 board. it's working fine.(eMMC/SD)
If it needs to change more, let me know, plz.
Best Regards,
Jaehoon Chung
On 03/03/2014 11:36 AM, Jaehoon Chung wrote:
> mmc_of_parse() have been already parsed the general capability.
> Didn't need to use the local parser.
>
> Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
> ---
> Changelog V4:
> - None
> Changelog V3:
> - Remove the caps2-mmc-hs-1_8v/1_2v into synopsys-dw-mshc.txt
> Changelog V2:
> - None
> .../devicetree/bindings/mmc/synopsys-dw-mshc.txt | 5 --
> drivers/mmc/host/dw_mmc.c | 49 +-------------------
> 2 files changed, 1 insertion(+), 53 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> index 8f3f133..2d4a725 100644
> --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
> @@ -69,10 +69,6 @@ Optional properties:
>
> * supports-highspeed: Enables support for high speed cards (up to 50MHz)
>
> -* caps2-mmc-hs200-1_8v: Supports mmc HS200 SDR 1.8V mode
> -
> -* caps2-mmc-hs200-1_2v: Supports mmc HS200 SDR 1.2V mode
> -
> * broken-cd: as documented in mmc core bindings.
>
> * vmmc-supply: The phandle to the regulator to use for vmmc. If this is
> @@ -103,7 +99,6 @@ board specific portions as listed below.
> clock-freq-min-max = <400000 200000000>;
> num-slots = <1>;
> supports-highspeed;
> - caps2-mmc-hs200-1_8v;
> broken-cd;
> fifo-depth = <0x80>;
> card-detect-delay = <200>;
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index 55cd110..8193e21 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -2046,21 +2046,6 @@ static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
> return quirks;
> }
>
> -/* find out bus-width for a given slot */
> -static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
> -{
> - struct device_node *np = dw_mci_of_find_slot_node(dev, slot);
> - u32 bus_wd = 1;
> -
> - if (!np)
> - return 1;
> -
> - if (of_property_read_u32(np, "bus-width", &bus_wd))
> - dev_err(dev, "bus-width property not found, assuming width"
> - " as 1\n");
> - return bus_wd;
> -}
> -
> /* find the write protect gpio for a given slot; or -1 if none specified */
> static int dw_mci_of_get_wp_gpio(struct device *dev, u8 slot)
> {
> @@ -2108,10 +2093,6 @@ static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
> {
> return 0;
> }
> -static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
> -{
> - return 1;
> -}
> static struct device_node *dw_mci_of_find_slot_node(struct device *dev, u8 slot)
> {
> return NULL;
> @@ -2134,7 +2115,6 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
> const struct dw_mci_drv_data *drv_data = host->drv_data;
> int ctrl_id, ret;
> u32 freq[2];
> - u8 bus_width;
>
> mmc = mmc_alloc_host(sizeof(struct dw_mci_slot), host->dev);
> if (!mmc)
> @@ -2189,19 +2169,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
> if (host->pdata->caps2)
> mmc->caps2 = host->pdata->caps2;
>
> - if (host->pdata->get_bus_wd)
> - bus_width = host->pdata->get_bus_wd(slot->id);
> - else if (host->dev->of_node)
> - bus_width = dw_mci_of_get_bus_wd(host->dev, slot->id);
> - else
> - bus_width = 1;
> -
> - switch (bus_width) {
> - case 8:
> - mmc->caps |= MMC_CAP_8_BIT_DATA;
> - case 4:
> - mmc->caps |= MMC_CAP_4_BIT_DATA;
> - }
> + mmc_of_parse(mmc);
>
> if (host->pdata->blk_settings) {
> mmc->max_segs = host->pdata->blk_settings->max_segs;
> @@ -2399,24 +2367,9 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
> return ERR_PTR(ret);
> }
>
> - if (of_find_property(np, "keep-power-in-suspend", NULL))
> - pdata->pm_caps |= MMC_PM_KEEP_POWER;
> -
> - if (of_find_property(np, "enable-sdio-wakeup", NULL))
> - pdata->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
> -
> if (of_find_property(np, "supports-highspeed", NULL))
> pdata->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
>
> - if (of_find_property(np, "caps2-mmc-hs200-1_8v", NULL))
> - pdata->caps2 |= MMC_CAP2_HS200_1_8V_SDR;
> -
> - if (of_find_property(np, "caps2-mmc-hs200-1_2v", NULL))
> - pdata->caps2 |= MMC_CAP2_HS200_1_2V_SDR;
> -
> - if (of_get_property(np, "cd-inverted", NULL))
> - pdata->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
> -
> return pdata;
> }
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
