[PATCH v4 1/7] mmc: dw_mmc: use the mmc_of_parse() instead of local parser

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



mmc_of_parse() have been already parsed the general capability.
Didn't need to use the local parser.

Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
---
Changelog V4:
	- None
Changelog V3:
	- Remove the caps2-mmc-hs-1_8v/1_2v into synopsys-dw-mshc.txt
Changelog V2:
	- None
 .../devicetree/bindings/mmc/synopsys-dw-mshc.txt   |    5 --
 drivers/mmc/host/dw_mmc.c                          |   49 +-------------------
 2 files changed, 1 insertion(+), 53 deletions(-)

diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
index 8f3f133..2d4a725 100644
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
@@ -69,10 +69,6 @@ Optional properties:
 
 * supports-highspeed: Enables support for high speed cards (up to 50MHz)
 
-* caps2-mmc-hs200-1_8v: Supports mmc HS200 SDR 1.8V mode
-
-* caps2-mmc-hs200-1_2v: Supports mmc HS200 SDR 1.2V mode
-
 * broken-cd: as documented in mmc core bindings.
 
 * vmmc-supply: The phandle to the regulator to use for vmmc.  If this is
@@ -103,7 +99,6 @@ board specific portions as listed below.
 		clock-freq-min-max = <400000 200000000>;
 		num-slots = <1>;
 		supports-highspeed;
-		caps2-mmc-hs200-1_8v;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 55cd110..8193e21 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -2046,21 +2046,6 @@ static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
 	return quirks;
 }
 
-/* find out bus-width for a given slot */
-static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
-{
-	struct device_node *np = dw_mci_of_find_slot_node(dev, slot);
-	u32 bus_wd = 1;
-
-	if (!np)
-		return 1;
-
-	if (of_property_read_u32(np, "bus-width", &bus_wd))
-		dev_err(dev, "bus-width property not found, assuming width"
-			       " as 1\n");
-	return bus_wd;
-}
-
 /* find the write protect gpio for a given slot; or -1 if none specified */
 static int dw_mci_of_get_wp_gpio(struct device *dev, u8 slot)
 {
@@ -2108,10 +2093,6 @@ static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
 {
 	return 0;
 }
-static u32 dw_mci_of_get_bus_wd(struct device *dev, u8 slot)
-{
-	return 1;
-}
 static struct device_node *dw_mci_of_find_slot_node(struct device *dev, u8 slot)
 {
 	return NULL;
@@ -2134,7 +2115,6 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 	const struct dw_mci_drv_data *drv_data = host->drv_data;
 	int ctrl_id, ret;
 	u32 freq[2];
-	u8 bus_width;
 
 	mmc = mmc_alloc_host(sizeof(struct dw_mci_slot), host->dev);
 	if (!mmc)
@@ -2189,19 +2169,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
 	if (host->pdata->caps2)
 		mmc->caps2 = host->pdata->caps2;
 
-	if (host->pdata->get_bus_wd)
-		bus_width = host->pdata->get_bus_wd(slot->id);
-	else if (host->dev->of_node)
-		bus_width = dw_mci_of_get_bus_wd(host->dev, slot->id);
-	else
-		bus_width = 1;
-
-	switch (bus_width) {
-	case 8:
-		mmc->caps |= MMC_CAP_8_BIT_DATA;
-	case 4:
-		mmc->caps |= MMC_CAP_4_BIT_DATA;
-	}
+	mmc_of_parse(mmc);
 
 	if (host->pdata->blk_settings) {
 		mmc->max_segs = host->pdata->blk_settings->max_segs;
@@ -2399,24 +2367,9 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
 			return ERR_PTR(ret);
 	}
 
-	if (of_find_property(np, "keep-power-in-suspend", NULL))
-		pdata->pm_caps |= MMC_PM_KEEP_POWER;
-
-	if (of_find_property(np, "enable-sdio-wakeup", NULL))
-		pdata->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
-
 	if (of_find_property(np, "supports-highspeed", NULL))
 		pdata->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
 
-	if (of_find_property(np, "caps2-mmc-hs200-1_8v", NULL))
-		pdata->caps2 |= MMC_CAP2_HS200_1_8V_SDR;
-
-	if (of_find_property(np, "caps2-mmc-hs200-1_2v", NULL))
-		pdata->caps2 |= MMC_CAP2_HS200_1_2V_SDR;
-
-	if (of_get_property(np, "cd-inverted", NULL))
-		pdata->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
-
 	return pdata;
 }
 
-- 
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux