On Mon, December 16, 2013, Zhangfei Gao wrote:
> On 12/16/2013 03:29 PM, Seungwon Jeon wrote:
> > On Mon, December 16, 2013, Zhangfei Gao wrote:
> >> Dear Seungwon
> >>
> >> On 12/16/2013 11:50 AM, Seungwon Jeon wrote:
> >>> On Sat, December 14, 2013, Zhangfei Gao wrote:
> >>
> >>>> + /* SoC portion */
> >>>> + dwmmc_0: dwmmc0@fcd03000 {
> >>>> + compatible = "hisilicon,hi4511-dw-mshc";
> >>>> + reg = <0xfcd03000 0x1000>;
> >>>> + interrupts = <0 16 4>;
> >>>> + #address-cells = <1>;
> >>>> + #size-cells = <0>;
> >>>> + clocks = <&mmc_clock HI3620_SD_CIUCLK>, <&clock HI3620_DDRC_PER_CLK>;
> >>>> + clock-names = "ciu", "biu";
> >>>> + clock-freq-table =
> >>>> + <25000000 0 50000000 25000000 50000000 100000000 0 50000000>;
> >>> I think it could be solved with mmc->f_min and mmc->f_max(from clock-freq-min-max property)
> >>> if there is no limitation per each speed mode. As seeing described table, it looks that.
> >>
> >> Have tried them before, but unfortunately, they are different.
> >>
> >> The controller can not generate clock itself, while depending on the
> >> outside clock generator, which may require to change clock source in
> >> differnt mode.
> >>
> >> The value we want is set the capacibility of the clock input and the max
> >> clock freq where mmc works stable in that mode, which may be different
> >> in different mode.
> >>
> >> clock-freq-min-max will set the value for set_ios.
> >> For example, we use 25M as clock capability when init, which can not be
> >> set as freq-min, and used as set_ios, where 400K should be used,
> >> otherwise init definitely fail.
> > Can you check 'f_init' within 'drivers/mmc/core/core.c' file?
> > If you set 'f_min = 25000000' for init-sequence, mmc_set_ios() will pass that rate through
> 'ios.clock'
> > Then, dw_mmc-k3 can do clk_set_rate() with 25MHz at dw_mci_k3_set_ios().
>
> This means controller directly use 25M init emmc and sd card, it will fail.
> We still need 400K init freq, while the input clock source is 25M,
> divided by the controller.
>
> > And other required speeds for each mode seem not specific compared with standard spec.
> > Also clk_set_rate() would be possible with 'ios.clock' instead of specific table.
> > I just referred your example's clock-freq-table above.
> There also some controller limitation currently.
> In some mode, the controller only works well in the limited freq.
> For example UHS_SDR104_MAX_DTR 208000000 can not be used, only half may
> be reached, at least currently
Ok. I see your condition. I misunderstood a little bit.
I wonder whether limitation is only max frequency(SDR104 or HS200) except for init-freq.
How about other mode? Working is fine with normal clock rate(from clock-freq-table)?
Thanks,
Seungwon Jeon
>
> >
> >>
> >>>> +static int dw_mci_k3_suspend(struct device *dev)
> >>>> +{
> >>>> + struct dw_mci *host = dev_get_drvdata(dev);
> >>>> +
> >>>> + if (!IS_ERR(host->ciu_clk))
> >>>> + clk_disable_unprepare(host->ciu_clk);
> >>>> +
> >>>> + return dw_mci_suspend(host);
> >>> If k3 needs clk_disable here, dw_mci_suspend()is expected to be called prior to
> >> clk_disable_unprepare()?
> >>> Of course, it's ok at present though.
> >>>
> >>
> >> Sure, it can be switched, though dw_mci_suspend does nothing related
> >> with clock now.
> > Yes, but if some works with ciu_clk is added in dw_mci_suspend(), it will affect.
> >
> Sorry for the misunderstood, I mean it make sense and will change.
> Thanks the advice.
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
