The DLL(Delay Line) is newly added to assist in sampling read data.
The DLL provides the ability to programmatically select a quantized
delay (in fractions of the clock period) regardless of on-chip variations
such as process, voltage and temperature (PVT).
This patch adds a user interface to set slave delay line via device tree.
It's usually used in high speed mode like mmc DDR mode when the signal
quality is not good caused by board design, e.g. the signal path is too long.
User can manual set delay line to find a suitable data sampling window
for card to work properly.
Signed-off-by: Dong Aisheng <b29396@xxxxxxxxxxxxx>
Acked-by: Shawn Guo <shawn.guo@xxxxxxxxxx>
---
.../devicetree/bindings/mmc/fsl-imx-esdhc.txt | 5 +++++
drivers/mmc/host/sdhci-esdhc-imx.c | 18 ++++++++++++++++++
include/linux/platform_data/mmc-esdhc-imx.h | 1 +
3 files changed, 24 insertions(+), 0 deletions(-)
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
index 1dd6225..9046ba06 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
@@ -12,6 +12,11 @@ Required properties:
Optional properties:
- fsl,cd-controller : Indicate to use controller internal card detection
- fsl,wp-controller : Indicate to use controller internal write protection
+- fsl,delay-line : Specify the number of delay cells for override mode.
+ This is used to set the clock delay for DLL(Delay Line) on override mode
+ to select a proper data sampling window in case the clock quality is not good
+ due to signal path is too long on the board. Please refer to eSDHC/uSDHC
+ chapter, DLL (Delay Line) section in RM for details.
Examples:
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 915fa68..260a81f 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -46,6 +46,11 @@
/* Bits 3 and 6 are not SDHCI standard definitions */
#define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
+/* dll control register */
+#define ESDHC_DLL_CTRL 0x60
+#define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9
+#define ESDHC_DLL_OVERRIDE_EN_SHIFT 8
+
/* tune control register */
#define ESDHC_TUNE_CTRL_STATUS 0x68
#define ESDHC_TUNE_CTRL_STEP 1
@@ -817,6 +822,7 @@ static int esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = pltfm_host->priv;
+ struct esdhc_platform_data *boarddata = &imx_data->boarddata;
switch (uhs) {
case MMC_TIMING_UHS_SDR12:
@@ -837,6 +843,15 @@ static int esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
ESDHC_MIX_CTRL_DDREN,
host->ioaddr + ESDHC_MIX_CTRL);
imx_data->is_ddr = 1;
+ if (boarddata->delay_line) {
+ u32 v;
+ v = boarddata->delay_line <<
+ ESDHC_DLL_OVERRIDE_VAL_SHIFT |
+ (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
+ if (is_imx53_esdhc(imx_data))
+ v <<= 1;
+ writel(v, host->ioaddr + ESDHC_DLL_CTRL);
+ }
break;
}
@@ -901,6 +916,9 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
else
boarddata->support_vsel = true;
+ if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
+ boarddata->delay_line = 0;
+
return 0;
}
#else
diff --git a/include/linux/platform_data/mmc-esdhc-imx.h b/include/linux/platform_data/mmc-esdhc-imx.h
index a0f5a8f..75f70f6 100644
--- a/include/linux/platform_data/mmc-esdhc-imx.h
+++ b/include/linux/platform_data/mmc-esdhc-imx.h
@@ -45,5 +45,6 @@ struct esdhc_platform_data {
int max_bus_width;
unsigned int f_max;
bool support_vsel;
+ unsigned int delay_line;
};
#endif /* __ASM_ARCH_IMX_ESDHC_H */
--
1.7.2.rc3
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
