> -----Original Message----- > From: linux-mmc-owner@xxxxxxxxxxxxxxx [mailto:linux-mmc- > owner@xxxxxxxxxxxxxxx] On Behalf Of Nath, Arindam > Sent: Thursday, March 10, 2011 4:15 PM > To: subhashj@xxxxxxxxxxxxxx; cjb@xxxxxxxxxx > Cc: zhangfei.gao@xxxxxxxxx; prakity@xxxxxxxxxxx; linux- > mmc@xxxxxxxxxxxxxxx; Su, Henry; Lu, Aaron; anath.amd@xxxxxxxxx > Subject: RE: [PATCH v2 04/12] mmc: sd: add support for driver type > selection > > Hi Subhash, > > > > -----Original Message----- > > From: subhashj@xxxxxxxxxxxxxx [mailto:subhashj@xxxxxxxxxxxxxx] > > Sent: Thursday, March 10, 2011 3:58 PM > > To: Nath, Arindam; cjb@xxxxxxxxxx > > Cc: zhangfei.gao@xxxxxxxxx; prakity@xxxxxxxxxxx; linux- > > mmc@xxxxxxxxxxxxxxx; Su, Henry; Lu, Aaron; anath.amd@xxxxxxxxx > > Subject: RE: [PATCH v2 04/12] mmc: sd: add support for driver type > > selection > > > > > > > > > -----Original Message----- > > > From: linux-mmc-owner@xxxxxxxxxxxxxxx [mailto:linux-mmc- > > > owner@xxxxxxxxxxxxxxx] On Behalf Of Nath, Arindam > > > Sent: Thursday, March 10, 2011 2:02 PM > > > To: subhashj@xxxxxxxxxxxxxx; cjb@xxxxxxxxxx > > > Cc: zhangfei.gao@xxxxxxxxx; prakity@xxxxxxxxxxx; linux- > > > mmc@xxxxxxxxxxxxxxx; Su, Henry; Lu, Aaron; anath.amd@xxxxxxxxx > > > Subject: RE: [PATCH v2 04/12] mmc: sd: add support for driver type > > > selection > > > > > > Hi Subhash, > > > > > > > > > > -----Original Message----- > > > > From: subhashj@xxxxxxxxxxxxxx [mailto:subhashj@xxxxxxxxxxxxxx] > > > > Sent: Thursday, March 10, 2011 12:27 PM > > > > To: Nath, Arindam; cjb@xxxxxxxxxx > > > > Cc: zhangfei.gao@xxxxxxxxx; prakity@xxxxxxxxxxx; linux- > > > > mmc@xxxxxxxxxxxxxxx; Su, Henry; Lu, Aaron; anath.amd@xxxxxxxxx > > > > Subject: RE: [PATCH v2 04/12] mmc: sd: add support for driver > type > > > > selection > > > > > > > > > > > > > > > > > -----Original Message----- > > > > > From: linux-mmc-owner@xxxxxxxxxxxxxxx [mailto:linux-mmc- > > > > > owner@xxxxxxxxxxxxxxx] On Behalf Of Arindam Nath > > > > > Sent: Friday, March 04, 2011 5:03 PM > > > > > To: cjb@xxxxxxxxxx > > > > > Cc: zhangfei.gao@xxxxxxxxx; prakity@xxxxxxxxxxx; > > > > > subhashj@xxxxxxxxxxxxxx; linux-mmc@xxxxxxxxxxxxxxx; > > > henry.su@xxxxxxx; > > > > > aaron.lu@xxxxxxx; anath.amd@xxxxxxxxx; Arindam Nath > > > > > Subject: [PATCH v2 04/12] mmc: sd: add support for driver type > > > > > selection > > > > > > > > > > This patch adds support for setting driver strength during UHS- > I > > > > > initialization prcedure. Since UHS-I cards set S18A (bit 24) in > > > > > response to ACMD41, we use this as a base for UHS-I > > initialization. > > > > > We modify the parameter list of mmc_sd_get_cid() so that we can > > > > > save the ROCR from ACMD41 to check whether bit 24 is set. > > > > > > > > > > We decide whether the Host Controller supports A, C, or D > driver > > > > > type depending on the Capabilities register. We then set the > > > > > appropriate driver type for the card using CMD6 mode 1. As per > > > > > Host Controller spec v3.00, we set driver type for the host > only > > > > > if Preset Value Enable in the Host Control2 register is not > set. > > > > > SDHCI_HOST_CONTROL has been renamed to SDHCI_HOST_CONTROL1 to > > > > > conform to the spec. > > > > > > > > > > Signed-off-by: Arindam Nath <arindam.nath@xxxxxxx> > > > > > --- > > > > > drivers/mmc/core/core.c | 9 +++ > > > > > drivers/mmc/core/core.h | 1 + > > > > > drivers/mmc/core/sd.c | 140 > > > > +++++++++++++++++++++++++++++++++++++- > > > > > -------- > > > > > drivers/mmc/core/sd.h | 3 +- > > > > > drivers/mmc/core/sdio.c | 3 +- > > > > > drivers/mmc/host/sdhci.c | 48 ++++++++++++---- > > > > > drivers/mmc/host/sdhci.h | 10 +++- > > > > > include/linux/mmc/card.h | 4 + > > > > > include/linux/mmc/host.h | 8 +++ > > > > > 9 files changed, 186 insertions(+), 40 deletions(-) > > > > > > > > > > diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c > > > > > index 6625c05..daa535a 100644 > > > > > --- a/drivers/mmc/core/core.c > > > > > +++ b/drivers/mmc/core/core.c > > > > > @@ -947,6 +947,15 @@ void mmc_set_timing(struct mmc_host *host, > > > > > unsigned int timing) > > > > > } > > > > > > > > > > /* > > > > > + * Select appropriate driver type for host. > > > > > + */ > > > > > +void mmc_set_driver_type(struct mmc_host *host, unsigned int > > > > drv_type) > > > > > +{ > > > > > + host->ios.drv_type = drv_type; > > > > > + mmc_set_ios(host); > > > > > +} > > > > > + > > > > > +/* > > > > > * Apply power to the MMC stack. This is a two-stage process. > > > > > * First, we enable power to the card without the clock > running. > > > > > * We then wait a bit for the power to stabilise. Finally, > > > > > diff --git a/drivers/mmc/core/core.h b/drivers/mmc/core/core.h > > > > > index ca1fdde..6114ca5 100644 > > > > > --- a/drivers/mmc/core/core.h > > > > > +++ b/drivers/mmc/core/core.h > > > > > @@ -42,6 +42,7 @@ void mmc_set_bus_width_ddr(struct mmc_host > > *host, > > > > > unsigned int width, > > > > > unsigned int ddr); > > > > > u32 mmc_select_voltage(struct mmc_host *host, u32 ocr); > > > > > void mmc_set_timing(struct mmc_host *host, unsigned int > timing); > > > > > +void mmc_set_driver_type(struct mmc_host *host, unsigned int > > > > > drv_type); > > > > > > > > > > static inline void mmc_delay(unsigned int ms) > > > > > { > > > > > diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c > > > > > index a63956b..f6a4fab 100644 > > > > > --- a/drivers/mmc/core/sd.c > > > > > +++ b/drivers/mmc/core/sd.c > > > > > @@ -426,6 +426,86 @@ out: > > > > > return err; > > > > > } > > > > > > > > > > +static int sd_select_driver_type(struct mmc_card *card, u8 > > > *status) > > > > > +{ > > > > > + int host_set_drv_type, card_set_drv_type; > > > > > > > > Why you need to use *set* in name? Just host_drv_type & > > card_drv_type > > > > is not > > > > enough? > > > > > > I wanted to emphasize on the fact that we are setting the values > for > > > host and card both. I don't have issues removing the *set* part. > > > > I don't think you need to use *set*. > > Okay with me. I will remove *set*. > > > > > > > > > > > > > > > + int err; > > > > > + > > > > > + /* > > > > > + * If the host doesn't support any of the Driver Types A,C > or > > > D, > > > > > + * default Driver Type B is used. > > > > > + */ > > > > > + if (!(card->host->caps & (MMC_CAP_DRIVER_TYPE_A | > > > > > MMC_CAP_DRIVER_TYPE_C > > > > > + | MMC_CAP_DRIVER_TYPE_D))) > > > > > + return 0; > > > > > + > > > > > + if (card->host->caps & MMC_CAP_DRIVER_TYPE_A) { > > > > > + host_set_drv_type = MMC_SET_DRIVER_TYPE_A; > > > > > + if (card->sw_caps.uhs_drv_type & SD_DRIVER_TYPE_A) > > > > > + card_set_drv_type = MMC_SET_DRIVER_TYPE_A; > > > > > + else if (card->sw_caps.uhs_drv_type & > > SD_DRIVER_TYPE_C) > > > > > + card_set_drv_type = MMC_SET_DRIVER_TYPE_C; > > > > > > > > Why you are combining TYPE_C under CAP_*_TYPE_A? > > > > > > Both the host and card can support multiple driver types, so we > need > > to > > > decide the appropriate setting for them based on their > capabilities. > > > > Agreed but here you are first checking that host is capable of TYPE_A > > or > > not. Then if it's capable of TYPE_A that doesn't guarantee that host > is > > capable of TYPE_C as well even if card supports both TYPE_A and > TYPE_C. > > Please refer to section 6.7.1.2 of the Physical Layer spec v3.01. As > per the description, it seemed to me like, since Driver Type C is > weaker than Driver Type A, a host with Type A can still drive a card of > Type C. I might have misunderstood the spec, so please correct me if > wrong. So this is what you are assuming: A > B > C > D. with above check you are ignoring TYPE_B then. Let's say you check host CAP TYPE_A and if it supports then you check if card supports TYPE_A or not. If it's not then you are directly jumping to TYPE_C. but according to spec TYPE_B is stronger than TYPE_C. Please check the section: 6.7.1.5 in spec. it says this: "whenever a stronger driver than type B is needed, driver type A can be selected and whenever a weaker driver than type B is needed, driver type C can be selected " > > > > > > > > > > > > > > > + } else if (card->host->caps & MMC_CAP_DRIVER_TYPE_C) { > > > > > + host_set_drv_type = MMC_SET_DRIVER_TYPE_C; > > > > > + if (card->sw_caps.uhs_drv_type & SD_DRIVER_TYPE_C) > > > > > + card_set_drv_type = MMC_SET_DRIVER_TYPE_C; > > > > > + } > > > > > > > > Again TYPE_C checking here? Also why are you skiping TYPE_D here? > > > > > > TYPE_C checking for the same reason as above. I could not find a > > > scenario where I can put TYPE_D into, so there is not checking. > > > Probably you can suggest something? > > > > Will following simple check is not enough? > > > > if (card->host->caps & MMC_CAP_DRIVER_TYPE_A) { > > host_set_drv_type = MMC_SET_DRIVER_TYPE_A; > > if (card->sw_caps.uhs_drv_type & SD_DRIVER_TYPE_A) > > card_set_drv_type = MMC_SET_DRIVER_TYPE_A; > > } else if (card->host->caps & MMC_CAP_DRIVER_TYPE_C) { > > host_set_drv_type = MMC_SET_DRIVER_TYPE_C; > > if (card->sw_caps.uhs_drv_type & SD_DRIVER_TYPE_C) > > card_set_drv_type = MMC_SET_DRIVER_TYPE_C; > > } else if (card->host->caps & MMC_CAP_DRIVER_TYPE_D) { > > host_set_drv_type = MMC_SET_DRIVER_TYPE_D; > > if (card->sw_caps.uhs_drv_type & SD_DRIVER_TYPE_D) > > card_set_drv_type = MMC_SET_DRIVER_TYPE_D; > > } else { > > return 0; /* default = TYPE_B */ > > } > > > > > > > > > > > > > > > > > > + > > > > > + err = mmc_sd_switch(card, 1, 2, card_set_drv_type, status); > > > > > + if (err) > > > > > + return err; > > > > > + > > > > > + if ((status[15] & 0xF) != card_set_drv_type) > > > > > + printk(KERN_WARNING "%s: Problem setting driver > > > > > strength!\n", > > > > > + mmc_hostname(card->host)); > > > > > + else > > > > > + mmc_set_driver_type(card->host, host_set_drv_type); > > > > > + > > > > > + return 0; > > > > > +} > > > > > + > > > > > +/* > > > > > + * UHS-I specific initialization procedure > > > > > + */ > > > > > +static int mmc_sd_init_uhs_card(struct mmc_card *card) > > > > > +{ > > > > > + int err; > > > > > + u8 *status; > > > > > + > > > > > + if (!card->scr.sda_spec3) > > > > > + return 0; > > > > > + > > > > > + if (!(card->csd.cmdclass & CCC_SWITCH)) > > > > > + return 0; > > > > > > > > We can combine both these check under single "if" checking. > > > > > > The code snippet is a replica of the code already present in > > > mmc_sd_switch_hs() and mmc_read_switch(), so I too followed the > same > > > checking. I can combine them into a single condition if you want. > > > > Ok. it's up to you in this case. If it looks by having 2 different > > statements then it's fine. > > > > > > > > > > > > > > + > > > > > + err = -EIO; > > > > > > > > Is this really required? I don't think initializing "err" is > needed > > > > here. > > > > > > Again a replica of the functions mentioned above. Let me know if > you > > > want this removed. > > > > This is not needed here. You can remove it. > > Will remove it then. Thanks. > > > > > > > > > > > > > > > + > > > > > + status = kmalloc(64, GFP_KERNEL); > > > > > + if (!status) { > > > > > + printk(KERN_ERR "%s: could not allocate a buffer > for > > " > > > > > + "switch capabilities.\n", > mmc_hostname(card- > > > >host)); > > > > > + return -ENOMEM; > > > > > + } > > > > > > > > You may want to allocate memory only after bus width setting is > > > > successful. > > > > > > Yes, good suggestion. I will incorporate this change. > > > > > > > > > > > > + > > > > > + /* Set 4-bit bus width */ > > > > > + if ((card->host->caps & MMC_CAP_4_BIT_DATA) && > > > > > + (card->scr.bus_widths & SD_SCR_BUS_WIDTH_4)) { > > > > > + err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4); > > > > > + if (err) > > > > > + goto out; > > > > > + > > > > > + mmc_set_bus_width(card->host, MMC_BUS_WIDTH_4); > > > > > + } > > > > > + > > > > > + /* Set the driver strength for the card */ > > > > > + err = sd_select_driver_type(card, status); > > > > > > > > Actually why are you allocating memory for "status" response in > > > > mmc_sd_init_uhs_card() function. You need "status" only in > > > > sd_select_driver_type() function. So you should be allocating > > memory > > > in > > > > sd_select_driver_type() function only. here you just say " > > > > sd_select_driver_type(card);" > > > > > > Please check the later patches. "status" is used to store return > > > statuses from *bus_speed_mode() and *current_limit() as well. So I > > > think it makes sense to allocate memory for "status" at the > beginning > > > of the function, and use it later. > > > > Sorry. I had not checked the later patches. Yes, allocating here is > > proper. > > As same status is being used for other switch settings as well. > > > > > > > > > > > > > > > > + > > > > > +out: > > > > > + kfree(status); > > > > > + > > > > > + return err; > > > > > +} > > > > > + > > > > > MMC_DEV_ATTR(cid, "%08x%08x%08x%08x\n", card->raw_cid[0], > card- > > > > > >raw_cid[1], > > > > > card->raw_cid[2], card->raw_cid[3]); > > > > > MMC_DEV_ATTR(csd, "%08x%08x%08x%08x\n", card->raw_csd[0], > card- > > > > > >raw_csd[1], > > > > > @@ -474,10 +554,10 @@ struct device_type sd_type = { > > > > > /* > > > > > * Fetch CID from card. > > > > > */ > > > > > -int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid) > > > > > +int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, > > > > > + u32 *rocr) > > > > > { > > > > > int err; > > > > > - u32 rocr; > > > > > > > > > > /* > > > > > * Since we're changing the OCR value, we seem to > > > > > @@ -502,7 +582,7 @@ int mmc_sd_get_cid(struct mmc_host *host, > u32 > > > > ocr, > > > > > u32 *cid) > > > > > MMC_CAP_SET_XPC_180)) > > > > > ocr |= 1 << 28; > > > > > > > > > > - err = mmc_send_app_op_cond(host, ocr, &rocr); > > > > > + err = mmc_send_app_op_cond(host, ocr, rocr); > > > > > if (err) > > > > > return err; > > > > > > > > > > @@ -510,7 +590,7 @@ int mmc_sd_get_cid(struct mmc_host *host, > u32 > > > > ocr, > > > > > u32 *cid) > > > > > * In case CCS and S18A in the response is set, start > Signal > > > > > Voltage > > > > > * Switch procedure. SPI mode doesn't support CMD11. > > > > > */ > > > > > - if (!mmc_host_is_spi(host) && (rocr & 0x41000000)) { > > > > > + if (!mmc_host_is_spi(host) && rocr && (*rocr & 0x41000000)) > { > > > > > > > > You are not doing NULL check for "rocr" in mmc_send_app_op_cond() > > but > > > > you > > > > are doing it here. Is it needed? If "rocr" is NULL then > > > > mmc_send_app_op_cond() itself will fail. > > > > > > I am actually checking rocr for NULL before returning from > > > mmc_send_app_op_cond(). Can you please check the function again to > > make > > > sure? > > Yes. It's fine. ignore this. > > > > > > > > > > > Also, you may need to check b31 (busy bit) of rocr because spec > > says > > > > this: > > > > "Section:4.2.3.1 CCS (Bit 30) and S18A (Bit 24) are valid when > Busy > > > > (Bit 31) > > > > is set to 1." > > > > > > The busy bit (bit 31) checking is already performed inside > > > mmc_send_app_op_cond(), cmd.resp[0] & MMC_CARD_BUSY. > > > > Ok. fine. > > > > > > > > > > > > > > err = mmc_start_voltage_switch(host); > > > > > if (err) > > > > > return err; > > > > > @@ -643,11 +723,12 @@ static int mmc_sd_init_card(struct > mmc_host > > > > > *host, u32 ocr, > > > > > struct mmc_card *card; > > > > > int err; > > > > > u32 cid[4]; > > > > > + u32 rocr; > > > > > > > > > > BUG_ON(!host); > > > > > WARN_ON(!host->claimed); > > > > > > > > > > - err = mmc_sd_get_cid(host, ocr, cid); > > > > > + err = mmc_sd_get_cid(host, ocr, cid, &rocr); > > > > > if (err) > > > > > return err; > > > > > > > > > > @@ -700,30 +781,37 @@ static int mmc_sd_init_card(struct > mmc_host > > > > > *host, u32 ocr, > > > > > if (err) > > > > > goto free_card; > > > > > > > > > > - /* > > > > > - * Attempt to change to high-speed (if supported) > > > > > - */ > > > > > - err = mmc_sd_switch_hs(card); > > > > > - if (err > 0) > > > > > - mmc_sd_go_highspeed(card); > > > > > - else if (err) > > > > > - goto free_card; > > > > > - > > > > > - /* > > > > > - * Set bus speed. > > > > > - */ > > > > > - mmc_set_clock(host, mmc_sd_get_max_clock(card)); > > > > > - > > > > > - /* > > > > > - * Switch to wider bus (if supported). > > > > > - */ > > > > > - if ((host->caps & MMC_CAP_4_BIT_DATA) && > > > > > - (card->scr.bus_widths & SD_SCR_BUS_WIDTH_4)) { > > > > > - err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4); > > > > > + /* Initialization sequence for UHS-I cards */ > > > > > + if (rocr & 0x01000000) { > > > > > > > > Instead of 0x01000000, you can use (1 << 24) to be more readable. > > > > > > I am okay with your suggestion. Will change it. > > > > > > Thanks, > > > Arindam > > > > > > > > > > > > + err = mmc_sd_init_uhs_card(card); > > > > > if (err) > > > > > goto free_card; > > > > > + } else { > > > > > + /* > > > > > + * Attempt to change to high-speed (if supported) > > > > > + */ > > > > > + err = mmc_sd_switch_hs(card); > > > > > + if (err > 0) > > > > > + mmc_sd_go_highspeed(card); > > > > > + else if (err) > > > > > + goto free_card; > > > > > + > > > > > + /* > > > > > + * Set bus speed. > > > > > + */ > > > > > + mmc_set_clock(host, mmc_sd_get_max_clock(card)); > > > > > > > > > > - mmc_set_bus_width(host, MMC_BUS_WIDTH_4); > > > > > + /* > > > > > + * Switch to wider bus (if supported). > > > > > + */ > > > > > + if ((host->caps & MMC_CAP_4_BIT_DATA) && > > > > > + (card->scr.bus_widths & > SD_SCR_BUS_WIDTH_4)) > > { > > > > > + err = mmc_app_set_bus_width(card, > > > MMC_BUS_WIDTH_4); > > > > > + if (err) > > > > > + goto free_card; > > > > > + > > > > > + mmc_set_bus_width(host, MMC_BUS_WIDTH_4); > > > > > + } > > > > > } > > > > > > > > > > host->card = card; > > > > > diff --git a/drivers/mmc/core/sd.h b/drivers/mmc/core/sd.h > > > > > index 3d8800f..5106b44 100644 > > > > > --- a/drivers/mmc/core/sd.h > > > > > +++ b/drivers/mmc/core/sd.h > > > > > @@ -5,7 +5,8 @@ > > > > > > > > > > extern struct device_type sd_type; > > > > > > > > > > -int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid); > > > > > +int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, > > > > > + u32 *rocr); > > > > > int mmc_sd_get_csd(struct mmc_host *host, struct mmc_card > > *card); > > > > > void mmc_decode_cid(struct mmc_card *card); > > > > > int mmc_sd_setup_card(struct mmc_host *host, struct mmc_card > > > *card, > > > > > diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c > > > > > index 5c4a54d..6d16684 100644 > > > > > --- a/drivers/mmc/core/sdio.c > > > > > +++ b/drivers/mmc/core/sdio.c > > > > > @@ -364,7 +364,8 @@ static int mmc_sdio_init_card(struct > mmc_host > > > > > *host, u32 ocr, > > > > > } > > > > > > > > > > if (ocr & R4_MEMORY_PRESENT > > > > > - && mmc_sd_get_cid(host, host->ocr & ocr, card->raw_cid) > > == > > > 0) > > > > > { > > > > > + && mmc_sd_get_cid(host, host->ocr & ocr, card->raw_cid, > > > > > + NULL) == 0) { > > > > > card->type = MMC_TYPE_SD_COMBO; > > > > > > > > > > if (oldcard && (oldcard->type != MMC_TYPE_SD_COMBO > || > > > > > diff --git a/drivers/mmc/host/sdhci.c > b/drivers/mmc/host/sdhci.c > > > > > index 5487a0b..1645687 100644 > > > > > --- a/drivers/mmc/host/sdhci.c > > > > > +++ b/drivers/mmc/host/sdhci.c > > > > > @@ -63,7 +63,7 @@ static void sdhci_dumpregs(struct sdhci_host > > > *host) > > > > > sdhci_readw(host, SDHCI_TRANSFER_MODE)); > > > > > printk(KERN_DEBUG DRIVER_NAME ": Present: 0x%08x | Host > ctl: > > > > > 0x%08x\n", > > > > > sdhci_readl(host, SDHCI_PRESENT_STATE), > > > > > - sdhci_readb(host, SDHCI_HOST_CONTROL)); > > > > > + sdhci_readb(host, SDHCI_HOST_CONTROL1)); > > > > > printk(KERN_DEBUG DRIVER_NAME ": Power: 0x%08x | Blk > gap: > > > > > 0x%08x\n", > > > > > sdhci_readb(host, SDHCI_POWER_CONTROL), > > > > > sdhci_readb(host, SDHCI_BLOCK_GAP_CONTROL)); > > > > > @@ -216,18 +216,18 @@ static void sdhci_activate_led(struct > > > > sdhci_host > > > > > *host) > > > > > { > > > > > u8 ctrl; > > > > > > > > > > - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL); > > > > > + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1); > > > > > ctrl |= SDHCI_CTRL_LED; > > > > > - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL); > > > > > + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1); > > > > > } > > > > > > > > > > static void sdhci_deactivate_led(struct sdhci_host *host) > > > > > { > > > > > u8 ctrl; > > > > > > > > > > - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL); > > > > > + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1); > > > > > ctrl &= ~SDHCI_CTRL_LED; > > > > > - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL); > > > > > + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1); > > > > > } > > > > > > > > > > #ifdef SDHCI_USE_LEDS_CLASS > > > > > @@ -786,14 +786,14 @@ static void sdhci_prepare_data(struct > > > > sdhci_host > > > > > *host, struct mmc_data *data) > > > > > * is ADMA. > > > > > */ > > > > > if (host->version >= SDHCI_SPEC_200) { > > > > > - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL); > > > > > + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1); > > > > > ctrl &= ~SDHCI_CTRL_DMA_MASK; > > > > > if ((host->flags & SDHCI_REQ_USE_DMA) && > > > > > (host->flags & SDHCI_USE_ADMA)) > > > > > ctrl |= SDHCI_CTRL_ADMA32; > > > > > else > > > > > ctrl |= SDHCI_CTRL_SDMA; > > > > > - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL); > > > > > + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1); > > > > > } > > > > > > > > > > if (!(host->flags & SDHCI_REQ_USE_DMA)) { > > > > > @@ -1252,7 +1252,7 @@ static void sdhci_set_ios(struct mmc_host > > > *mmc, > > > > > struct mmc_ios *ios) > > > > > if (host->ops->platform_8bit_width) > > > > > host->ops->platform_8bit_width(host, ios- > >bus_width); > > > > > else { > > > > > - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL); > > > > > + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1); > > > > > if (ios->bus_width == MMC_BUS_WIDTH_8) { > > > > > ctrl &= ~SDHCI_CTRL_4BITBUS; > > > > > if (host->version >= SDHCI_SPEC_300) > > > > > @@ -1265,10 +1265,10 @@ static void sdhci_set_ios(struct > mmc_host > > > > *mmc, > > > > > struct mmc_ios *ios) > > > > > else > > > > > ctrl &= ~SDHCI_CTRL_4BITBUS; > > > > > } > > > > > - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL); > > > > > + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1); > > > > > } > > > > > > > > > > - ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL); > > > > > + ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL1); > > > > > > > > > > if ((ios->timing == MMC_TIMING_SD_HS || > > > > > ios->timing == MMC_TIMING_MMC_HS) > > > > > @@ -1277,7 +1277,25 @@ static void sdhci_set_ios(struct > mmc_host > > > > *mmc, > > > > > struct mmc_ios *ios) > > > > > else > > > > > ctrl &= ~SDHCI_CTRL_HISPD; > > > > > > > > > > - sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL); > > > > > + sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL1); > > > > > + > > > > > + if (host->version >= SDHCI_SPEC_300) { > > > > > + u16 ctrl_2; > > > > > + > > > > > + ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); > > > > > + if (!(ctrl_2 & SDHCI_CTRL_PRESET_VAL_ENABLE)) { > > > > > + /* > > > > > + * We only need to set Driver Strength if > the > > > > > + * preset value enable is not set. > > > > > + */ > > > > > + if (ios->drv_type == MMC_SET_DRIVER_TYPE_A) > > > > > + ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A; > > > > > + else if (ios->drv_type == > > > MMC_SET_DRIVER_TYPE_C) > > > > > + ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C; > > > > > + > > > > > + sdhci_writew(host, ctrl_2, > > > SDHCI_HOST_CONTROL2); > > > > > + } > > > > > + } > > > > > > > > > > /* > > > > > * Some (ENE) controllers go apeshit on some ios operation, > > > > > @@ -2037,6 +2055,14 @@ int sdhci_add_host(struct sdhci_host > > *host) > > > > > if (caps[1] & SDHCI_SUPPORT_DDR50) > > > > > mmc->caps |= MMC_CAP_UHS_DDR50; > > > > > > > > > > + /* Driver Type(s) (A, C, D) supported by the host */ > > > > > + if (caps[1] & SDHCI_DRIVER_TYPE_A) > > > > > + mmc->caps |= MMC_CAP_DRIVER_TYPE_A; > > > > > + if (caps[1] & SDHCI_DRIVER_TYPE_C) > > > > > + mmc->caps |= MMC_CAP_DRIVER_TYPE_C; > > > > > + if (caps[1] & SDHCI_DRIVER_TYPE_D) > > > > > + mmc->caps |= MMC_CAP_DRIVER_TYPE_D; > > > > > + > > > > > ocr_avail = 0; > > > > > /* > > > > > * According to SD Host Controller spec v3.00, if the Host > > > System > > > > > diff --git a/drivers/mmc/host/sdhci.h > b/drivers/mmc/host/sdhci.h > > > > > index 95d70e6..a407b5b 100644 > > > > > --- a/drivers/mmc/host/sdhci.h > > > > > +++ b/drivers/mmc/host/sdhci.h > > > > > @@ -72,7 +72,7 @@ > > > > > #define SDHCI_DATA_LVL_MASK 0x00F00000 > > > > > #define SDHCI_DATA_LVL_SHIFT 20 > > > > > > > > > > -#define SDHCI_HOST_CONTROL 0x28 > > > > > +#define SDHCI_HOST_CONTROL1 0x28 > > > > > #define SDHCI_CTRL_LED 0x01 > > > > > #define SDHCI_CTRL_4BITBUS 0x02 > > > > > #define SDHCI_CTRL_HISPD 0x04 > > > > > @@ -151,6 +151,11 @@ > > > > > > > > > > #define SDHCI_HOST_CONTROL2 0x3E > > > > > #define SDHCI_CTRL_VDD_180 0x0008 > > > > > +#define SDHCI_CTRL_DRV_TYPE_B 0x0000 > > > > > +#define SDHCI_CTRL_DRV_TYPE_A 0x0010 > > > > > +#define SDHCI_CTRL_DRV_TYPE_C 0x0020 > > > > > +#define SDHCI_CTRL_DRV_TYPE_D 0x0030 > > > > > +#define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000 > > > > > > > > > > #define SDHCI_CAPABILITIES 0x40 > > > > > #define SDHCI_TIMEOUT_CLK_MASK 0x0000003F > > > > > @@ -174,6 +179,9 @@ > > > > > #define SDHCI_SUPPORT_SDR50 0x00000001 > > > > > #define SDHCI_SUPPORT_SDR104 0x00000002 > > > > > #define SDHCI_SUPPORT_DDR50 0x00000004 > > > > > +#define SDHCI_DRIVER_TYPE_A 0x00000010 > > > > > +#define SDHCI_DRIVER_TYPE_C 0x00000020 > > > > > +#define SDHCI_DRIVER_TYPE_D 0x00000040 > > > > > > > > > > #define SDHCI_CAPABILITIES_1 0x44 > > > > > > > > > > diff --git a/include/linux/mmc/card.h > b/include/linux/mmc/card.h > > > > > index 7080f22..2d7f7a3 100644 > > > > > --- a/include/linux/mmc/card.h > > > > > +++ b/include/linux/mmc/card.h > > > > > @@ -77,6 +77,10 @@ struct sd_switch_caps { > > > > > unsigned int hs_max_dtr; > > > > > unsigned int uhs_bus_mode; > > > > > unsigned int uhs_drv_type; > > > > > +#define SD_DRIVER_TYPE_B 0x01 > > > > > +#define SD_DRIVER_TYPE_A 0x02 > > > > > +#define SD_DRIVER_TYPE_C 0x04 > > > > > +#define SD_DRIVER_TYPE_D 0x08 > > > > > unsigned int uhs_curr_limit; > > > > > }; > > > > > > > > > > diff --git a/include/linux/mmc/host.h > b/include/linux/mmc/host.h > > > > > index ad7daa3..bc2121e 100644 > > > > > --- a/include/linux/mmc/host.h > > > > > +++ b/include/linux/mmc/host.h > > > > > @@ -56,6 +56,11 @@ struct mmc_ios { > > > > > #define MMC_SDR_MODE 0 > > > > > #define MMC_1_2V_DDR_MODE 1 > > > > > #define MMC_1_8V_DDR_MODE 2 > > > > > + > > > > > + unsigned char drv_type; /* driver type (A, > C, > > > D) */ > > > > > + > > > > > +#define MMC_SET_DRIVER_TYPE_A 1 > > > > > +#define MMC_SET_DRIVER_TYPE_C 2 > > > > > > > > *SET* is not required in name. again why are we ignoring TYPE D > > here? > > > > > > > > > }; > > > > > > > > > > struct mmc_host_ops { > > > > > @@ -183,6 +188,9 @@ struct mmc_host { > > > > > #define MMC_CAP_SET_XPC_330 (1 << 20) /* Host > > > supports >150mA > > > > > current at 3.3V */ > > > > > #define MMC_CAP_SET_XPC_300 (1 << 21) /* Host > > > supports >150mA > > > > > current at 3.0V */ > > > > > #define MMC_CAP_SET_XPC_180 (1 << 22) /* Host > > > supports >150mA > > > > > current at 1.8V */ > > > > > +#define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host > > > supports > > > > Driver > > > > > Type A */ > > > > > +#define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host > > > supports > > > > Driver > > > > > Type C */ > > > > > +#define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host > > > supports > > > > Driver > > > > > Type D */ > > > > > > > > > > mmc_pm_flag_t pm_caps; /* supported pm > > > features */ > > > > > > > > > > -- > > > > > 1.7.1 > > > > > > > > > > -- > > > > > To unsubscribe from this list: send the line "unsubscribe > linux- > > > mmc" > > > > in > > > > > the body of a message to majordomo@xxxxxxxxxxxxxxx > > > > > More majordomo info at http://vger.kernel.org/majordomo- > > info.html > > > > > > > > > > > > > -- > > > To unsubscribe from this list: send the line "unsubscribe linux- > mmc" > > in > > > the body of a message to majordomo@xxxxxxxxxxxxxxx > > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-mmc" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-mmc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
