On 5/5/2010 3:05 PM, Viresh KUMAR wrote:
> This patch adds glue layer for support of sdhci driver on ST SPEAr platform.
>
> Signed-off-by: Viresh Kumar <viresh.kumar@xxxxxx>
> ---
> MAINTAINERS | 6 +
> drivers/mmc/host/Kconfig | 12 ++
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/sdhci-spear.c | 300 +++++++++++++++++++++++++++++++++++++++
> include/linux/mmc/sdhci-spear.h | 42 ++++++
> 5 files changed, 361 insertions(+), 0 deletions(-)
> create mode 100644 drivers/mmc/host/sdhci-spear.c
> create mode 100644 include/linux/mmc/sdhci-spear.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 0369b22..bbff70a 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -4938,6 +4938,12 @@ L: linux-mmc@xxxxxxxxxxxxxxx
> S: Maintained
> F: drivers/mmc/host/sdhci-s3c.c
>
> +SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) ST SPEAR DRIVER
> +M: Viresh Kumar <viresh.kumar@xxxxxx>
> +L: linux-mmc@xxxxxxxxxxxxxxx
> +S: Maintained
> +F: drivers/mmc/host/sdhci-spear.c
> +
> SECURITY SUBSYSTEM
> M: James Morris <jmorris@xxxxxxxxx>
> L: linux-security-module@xxxxxxxxxxxxxxx (suggested Cc:)
> diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
> index 2e13b94..40eae7e 100644
> --- a/drivers/mmc/host/Kconfig
> +++ b/drivers/mmc/host/Kconfig
> @@ -136,6 +136,18 @@ config MMC_SDHCI_S3C
>
> If unsure, say N.
>
> +config MMC_SDHCI_SPEAR
> + tristate "SDHCI support on ST SPEAr platform"
> + depends on MMC_SDHCI && PLAT_SPEAR
> + help
> + This selects the Secure Digital Host Controller Interface (SDHCI)
> + often referrered to as the HSMMC block in some of the ST SPEAR range
> + of SoC
> +
> + If you have a controller with this interface, say Y or M here.
> +
> + If unsure, say N.
> +
> config MMC_SDHCI_S3C_DMA
> bool "DMA support on S3C SDHCI"
> depends on MMC_SDHCI_S3C && EXPERIMENTAL
> diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
> index f480397..d00a9fa 100644
> --- a/drivers/mmc/host/Makefile
> +++ b/drivers/mmc/host/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_MMC_SDHCI) += sdhci.o
> obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
> obj-$(CONFIG_MMC_SDHCI_PLTFM) += sdhci-pltfm.o
> obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c.o
> +obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o
> obj-$(CONFIG_MMC_WBSD) += wbsd.o
> obj-$(CONFIG_MMC_AU1X) += au1xmmc.o
> obj-$(CONFIG_MMC_OMAP) += omap.o
> diff --git a/drivers/mmc/host/sdhci-spear.c b/drivers/mmc/host/sdhci-spear.c
> new file mode 100644
> index 0000000..6d3f740
> --- /dev/null
> +++ b/drivers/mmc/host/sdhci-spear.c
> @@ -0,0 +1,300 @@
> +/*
> + * drivers/mmc/host/sdhci-spear.c
> + *
> + * Support of SDHCI platform devices for spear soc family
> + *
> + * Copyright (C) 2010 ST Microelectronics
> + * Viresh Kumar<viresh.kumar@xxxxxx>
> + *
> + * Inspired by sdhci-pltfm.c
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/gpio.h>
> +#include <linux/highmem.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/mmc/host.h>
> +#include <linux/mmc/sdhci-spear.h>
> +#include <linux/io.h>
> +#include "sdhci.h"
> +
> +struct spear_sdhci {
> + struct clk *clk;
> + struct sdhci_plat_data *data;
> +};
> +
> +/* sdhci ops */
> +static struct sdhci_ops sdhci_pltfm_ops = {
> + /* Nothing to do for now. */
> +};
> +
> +/* gpio card detection interrupt handler */
> +static irqreturn_t sdhci_gpio_irq(int irq, void *dev_id)
> +{
> + struct platform_device *pdev = dev_id;
> + struct sdhci_host *host = platform_get_drvdata(pdev);
> + struct spear_sdhci *sdhci =
> + (struct spear_sdhci *)(pdev->dev.platform_data);
> + unsigned long gpio_irq_type;
> + int val;
> +
> + val = gpio_get_value(sdhci->data->card_int_gpio);
> +
> + /* val == 1 -> card removed, val == 0 -> card inserted */
> + /* if card removed - set irq for low level, else vice versa */
> + gpio_irq_type = val ? IRQF_TRIGGER_LOW : IRQF_TRIGGER_HIGH;
> + set_irq_type(irq, gpio_irq_type);
> +
> + if (sdhci->data->card_power_gpio >= 0) {
> + if (!sdhci->data->power_always_enb) {
> + /* if card inserted, give power, otherwise remove it */
> + val = sdhci->data->power_active_high ? !val : val ;
> + gpio_set_value(sdhci->data->card_power_gpio, val);
> + }
> + }
> +
> + /* inform sdhci driver about card insertion/removal */
> + tasklet_schedule(&host->card_tasklet);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int __devinit sdhci_probe(struct platform_device *pdev)
> +{
> + struct sdhci_host *host;
> + struct resource *iomem;
> + struct spear_sdhci *sdhci;
> + int ret;
> +
> + BUG_ON(pdev == NULL);
> +
> + iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!iomem) {
> + ret = -ENOMEM;
> + dev_dbg(&pdev->dev, "memory resource not defined\n");
> + goto err;
> + }
> +
> + if (!request_mem_region(iomem->start, resource_size(iomem),
> + "spear-sdhci")) {
> + ret = -EBUSY;
> + dev_dbg(&pdev->dev, "cannot request region\n");
> + goto err;
> + }
> +
> + sdhci = kzalloc(sizeof(*sdhci), GFP_KERNEL);
> + if (!sdhci) {
> + ret = -ENOMEM;
> + dev_dbg(&pdev->dev, "cannot allocate memory for sdhci\n");
> + goto err_kzalloc;
> + }
> +
> + /* clk enable */
> + sdhci->clk = clk_get(&pdev->dev, NULL);
> + if (IS_ERR(sdhci->clk)) {
> + ret = PTR_ERR(sdhci->clk);
> + dev_dbg(&pdev->dev, "Error getting clock\n");
> + goto err_clk_get;
> + }
> +
> + ret = clk_enable(sdhci->clk);
> + if (ret) {
> + dev_dbg(&pdev->dev, "Error enabling clock\n");
> + goto err_clk_enb;
> + }
> +
> + /* overwrite platform_data */
> + sdhci->data = (struct sdhci_plat_data *)(pdev->dev.platform_data);
> + pdev->dev.platform_data = sdhci;
> +
> + if (pdev->dev.parent)
> + host = sdhci_alloc_host(pdev->dev.parent, 0);
> + else
> + host = sdhci_alloc_host(&pdev->dev, 0);
> +
> + if (IS_ERR(host)) {
> + ret = PTR_ERR(host);
> + dev_dbg(&pdev->dev, "error allocating host\n");
> + goto err_alloc_host;
> + }
> +
> + host->hw_name = "sdhci";
> + host->ops = &sdhci_pltfm_ops;
> + host->irq = platform_get_irq(pdev, 0);
> + host->quirks = SDHCI_QUIRK_BROKEN_ADMA;
> +
> + host->ioaddr = ioremap(iomem->start, resource_size(iomem));
> + if (!host->ioaddr) {
> + ret = -ENOMEM;
> + dev_dbg(&pdev->dev, "failed to remap registers\n");
> + goto err_ioremap;
> + }
> +
> + ret = sdhci_add_host(host);
> + if (ret) {
> + dev_dbg(&pdev->dev, "error adding host\n");
> + goto err_add_host;
> + }
> +
> + platform_set_drvdata(pdev, host);
> +
> + /*
> + * It is optional to use GPIOs for sdhci Power control & sdhci card
> + * interrupt detection. If sdhci->data is NULL, then use original sdhci
> + * lines otherwise GPIO lines.
> + * If GPIO is selected for power control, then power should be disabled
> + * after card removal and should be enabled when card insertion
> + * interrupt occurs
> + */
> + if (!sdhci->data)
> + return 0;
> +
> + if (sdhci->data->card_power_gpio >= 0) {
> + int val = 0;
> +
> + ret = gpio_request(sdhci->data->card_power_gpio, "sdhci");
> + if (ret < 0) {
> + dev_dbg(&pdev->dev, "gpio request fail: %d\n",
> + sdhci->data->card_power_gpio);
> + goto err_pgpio_request;
> + }
> +
> + if (sdhci->data->power_always_enb)
> + val = sdhci->data->power_active_high;
> + else
> + val = !sdhci->data->power_active_high;
> +
> + ret = gpio_direction_output(sdhci->data->card_power_gpio, val);
> + if (ret) {
> + dev_dbg(&pdev->dev, "gpio set direction fail: %d\n",
> + sdhci->data->card_power_gpio);
> + goto err_pgpio_direction;
> + }
> +
> + gpio_set_value(sdhci->data->card_power_gpio, 1);
> + }
> +
> + if (sdhci->data->card_int_gpio >= 0) {
> + ret = gpio_request(sdhci->data->card_int_gpio, "sdhci");
> + if (ret < 0) {
> + dev_dbg(&pdev->dev, "gpio request fail: %d\n",
> + sdhci->data->card_int_gpio);
> + goto err_igpio_request;
> + }
> +
> + ret = gpio_direction_input(sdhci->data->card_int_gpio);
> + if (ret) {
> + dev_dbg(&pdev->dev, "gpio set direction fail: %d\n",
> + sdhci->data->card_int_gpio);
> + goto err_igpio_direction;
> + }
> + ret = request_irq(gpio_to_irq(sdhci->data->card_int_gpio),
> + sdhci_gpio_irq, IRQF_TRIGGER_LOW,
> + mmc_hostname(host->mmc), pdev);
> + if (ret) {
> + dev_dbg(&pdev->dev, "gpio request irq fail: %d\n",
> + sdhci->data->card_int_gpio);
> + goto err_igpio_request_irq;
> + }
> +
> + }
> +
> + return 0;
> +
> +err_igpio_request_irq:
> +err_igpio_direction:
> + if (sdhci->data->card_int_gpio >= 0)
> + gpio_free(sdhci->data->card_int_gpio);
> +err_igpio_request:
> +err_pgpio_direction:
> + if (sdhci->data->card_power_gpio >= 0)
> + gpio_free(sdhci->data->card_power_gpio);
> +err_pgpio_request:
> + platform_set_drvdata(pdev, NULL);
> + sdhci_remove_host(host, 1);
> +err_add_host:
> + iounmap(host->ioaddr);
> +err_ioremap:
> + sdhci_free_host(host);
> +err_alloc_host:
> + clk_disable(sdhci->clk);
> +err_clk_enb:
> + clk_put(sdhci->clk);
> +err_clk_get:
> + kfree(sdhci);
> +err_kzalloc:
> + release_mem_region(iomem->start, resource_size(iomem));
> +err:
> + dev_err(&pdev->dev, "spear-sdhci probe failed: %d\n", ret);
> + return ret;
> +}
> +
> +static int __devexit sdhci_remove(struct platform_device *pdev)
> +{
> + struct sdhci_host *host = platform_get_drvdata(pdev);
> + struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + struct spear_sdhci *sdhci =
> + (struct spear_sdhci *)(pdev->dev.platform_data);
> + int dead;
> + u32 scratch;
> +
> + if (sdhci->data) {
> + if (sdhci->data->card_int_gpio >= 0) {
> + free_irq(gpio_to_irq(sdhci->data->card_int_gpio), pdev);
> + gpio_free(sdhci->data->card_int_gpio);
> + }
> +
> + if (sdhci->data->card_power_gpio >= 0)
> + gpio_free(sdhci->data->card_power_gpio);
> + }
> +
> + platform_set_drvdata(pdev, NULL);
> + dead = 0;
> + scratch = readl(host->ioaddr + SDHCI_INT_STATUS);
> + if (scratch == (u32)-1)
> + dead = 1;
> +
> + sdhci_remove_host(host, dead);
> + iounmap(host->ioaddr);
> + sdhci_free_host(host);
> + clk_disable(sdhci->clk);
> + clk_put(sdhci->clk);
> + kfree(sdhci);
> + if (iomem)
> + release_mem_region(iomem->start, resource_size(iomem));
> +
> + return 0;
> +}
> +
> +static struct platform_driver sdhci_driver = {
> + .driver = {
> + .name = "sdhci",
> + .owner = THIS_MODULE,
> + },
> + .probe = sdhci_probe,
> + .remove = __devexit_p(sdhci_remove),
> +};
> +
> +static int __init sdhci_init(void)
> +{
> + return platform_driver_register(&sdhci_driver);
> +}
> +module_init(sdhci_init);
> +
> +static void __exit sdhci_exit(void)
> +{
> + platform_driver_unregister(&sdhci_driver);
> +}
> +module_exit(sdhci_exit);
> +
> +MODULE_DESCRIPTION("SPEAr Secure Digital Host Controller Interface driver");
> +MODULE_AUTHOR("Viresh Kumar <viresh.kumar@xxxxxx>");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mmc/sdhci-spear.h b/include/linux/mmc/sdhci-spear.h
> new file mode 100644
> index 0000000..9188c97
> --- /dev/null
> +++ b/include/linux/mmc/sdhci-spear.h
> @@ -0,0 +1,42 @@
> +/*
> + * include/linux/mmc/sdhci-spear.h
> + *
> + * SDHCI declarations specific to ST SPEAr platform
> + *
> + * Copyright (C) 2010 ST Microelectronics
> + * Viresh Kumar<viresh.kumar@xxxxxx>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#ifndef MMC_SDHCI_SPEAR_H
> +#define MMC_SDHCI_SPEAR_H
> +
> +#include <linux/platform_device.h>
> +/*
> + * struct sdhci_plat_data: spear sdhci platform data structure
> + *
> + * @card_power_gpio: gpio pin for enabling/disabling power to sdhci socket
> + * @power_active_high: if set, enable power to sdhci socket by setting
> + * card_power_gpio
> + * @power_always_enb: If set, then enable power on probe, otherwise enable only
> + * on card insertion and disable on card removal.
> + * card_int_gpio: gpio pin used for card detection
> + */
> +struct sdhci_plat_data {
> + int card_power_gpio;
> + int power_active_high;
> + int power_always_enb;
> + int card_int_gpio;
> +};
> +
> +/* This function is used to set platform_data field of pdev->dev */
> +static inline void
> +sdhci_set_plat_data(struct platform_device *pdev, struct sdhci_plat_data *data)
> +{
> + pdev->dev.platform_data = data;
> +}
> +
> +#endif /* MMC_SDHCI_SPEAR_H */
Pierre,
Is this patch fine? Or do i need to do some modifications?
regards,
viresh kumar.
--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
